FORCE 2022 Helmet For Cyclists Instruction Manual
- June 6, 2024
- FORCE
Table of Contents
FORCE 2022 Helmet For Cyclists
Product Specifications
- Origin : Wenling City, Zhejiang, China
Product Usage Instructions
Correct Fit of the Helmet:
- Look upwards to make sure you can only see the edge of the helmet.
- The side straps should be attached just below the ears, in the shape of a ‘Y’.
- When you fasten the strap and open your mouth wide, you should feel the helmet pulling down.
Helmet Positioning:
The buyer must try different sizes and choose a helmet that fits securely and
comfortably on their head. The helmet should be positioned correctly on the
head, not too far back, to protect the front of the head. The chin strap, once
adjusted correctly, should fit snuglyand comfortably under the chin (away from
the jaw) so that the helmet stays on the head in case of a fall. The straps
and buckle must be adjusted comfortably and securely. The original components
of the helmet should not be removed or modified under any circumstances. Do
not wear the helmet too far back; it should fit to protect the front of the
head.
Helmet Maintenance:
If the helmet has undergone a strong impact, the damaged piece must be
replaced and disposed of. Choose the correct helmet size based on head
circumference in cm. The helmet should conform to Regulation (EU) 2016/425 of
the European Parliament and Council dated March 9, 2016, on personal
protective equipment.
Additional Information:
For further details and evaluation, visit
www.force.bike in the Downloads section for the
specific product.
Importer : Technology Development District, Guangzhou, China.
INSTRUCTIONS FOR USE
This is a helmet for cyclists providing protection for the top of the user’s head. Suitable for cycling or scooter riding. This product is personal protective equipment whose primary function is to protect the top of the user’s head from hazards that may arise during cycling and scooter riding activities. The device protects the head from impacts where part of the impact energy is absorbed by the helmet, thereby reducing the impact energy to which the head is exposed. The protection provided by the helmet depends on the circumstances surrounding the injury and cannot always protect against injury. The helmet only protects if it is well seated on the head. The buyer must try on different sizes and choose a helmet that fits his or her head securely and comfortably. With the help of spare padding (not applicable for integral helmets), the internal size can be adjusted to the optimum shape. The helmet must be adapted to the user. Correct routing of the strap under the chin without covering the ears is essential. The buckle, when properly adjusted, should fit snugly and comfortably under the chin (away from the jaw) so that the helmet stays on the head in the event of a fall. The straps and buckle must be comfortably and firmly adjusted. The helmet must not be worn too far back and must fit so as to protect the front of the head. Original helmet components must not be removed or altered under any circumstances. Do not expose the helmet to temperatures exceeding 60°C, do not clean with synthetic agents (lukewarm water is sufficient). Helmets damaged by a fall must no longer be used! The helmet must not be used for activities other than those for which it is intended (do not use when riding a motorcycle)! Warning! This helmet is not to be used by children when climbing and other activities in which there is a risk of strangulation/hanging by the helmet in the event of a child falling! Never pull over the stop when adjusting the wheel! If the helmet has been subjected to a severe impact the damaged piece must be replaced and disposed of. Select the correct helmet size according to the head circumference in cm. The above also applies to integral cycle helmets with regard to their construction and specification. We declare that this cycle helmet complies with Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment. Notified Body involved in the conformity assessment of PPE; SGS, 198 Kezhu Road, Scientech Park Guangzhou Economic and Technology Development District, Guangzhou, China;
TR : GZHL2309031292HM-1. The current Declaration of Conformity can be found on the website www.force.bike in the “Documents to download” section for the product concerned.
Importer : KCK Cyklosport-Mode s.r.o., Bartošova 348, 765 02 Otrokovice- Kvítkovice, Czech Republic
The correct fit of the helmet (points 1 and 2 do not apply to integral helmets):
- Look upwards to make sure you can only see the edge of the helmet.
- The side straps should be attached just below the ears, in the shape of a ‘Y’.
- When you fasten the strap and open your mouth wide, you should feel the helmet pulling down.
FAQ
Q: How do I determine the correct size for my helmet?
A: Choose the correct helmet size based on your head circumference in
centimetres.
Q: What should I do if my helmet has been involved in a strong impact?
A: If your helmet has undergone a strong impact, replace the damaged piece and
dispose of it properly.