EDiMAX GP-101ST Gigabit PoE+ Splitter with Adjustable 5V DC Installation Guide

: June 3, 2024
: EDIMAX

Table of Contents

EDiMAX GP-101ST Gigabit PoE+ Splitter with Adjustable 5V DC
Product Information
Federal Communication Commission Interference Statement
EU Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EDiMAX GP-101ST Gigabit PoE+ Splitter with Adjustable 5V DC

Product Information

Package Contents

Hardware Overview & LED Status

Code	Name	Indication / Function

Hardware Overview

A

| ****

DATA OUT

| Supports 10/100/1000 base Ethernet. Connect to the Ethernet device with standard Ethernet cable to transmit data.

B

| ****

DC OUT

| Connect to the power port of the Ethernet device with the provided power cable to supply the power of 5V, 9V,or 12V.

C

| ****

PWR+DATA IN

| Supports 10/100/1000 PoE over Ethernet. Connect to the PSE or PoE Injector with a standard Ethernet cable.

D

| ****

DC OUT Switch

| Choose the DC output of 5V, 9V or 12V by adjusting the slide switch to the left or right.

Please make sure that the DC output power is correct, a different voltage may destroy the device.

LED Status
1| POWER LED| For Adjustable 5VDC / 9VDC / 12VDC

Connections
Connect the splitter as shown below: EDiMAX-GP-101ST-Gigabit-PoE+-Splitter-
with-Adjustable-5V-DC-FIG3

Use a standard Ethernet cable to connect a PoE port of the PSE (e.g. PoE Switch) to the POWER+DATA IN port.
Choose the appropriate DC output by the Power-mode switch, Please make sure that the output is correct, a different voltage may destroy the device.
Connect the LAN OUT port to the Ethernet device with standard Ethernet cable for data transmitting.
Connect the DC OUT port to the power port of the same Ethernet device with the provided power cable.

COPYRIGHT
Copyright C Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revisions or changes. The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio technician for help.

FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate the equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 2.5cm (1 inch) during normal operation.
Federal Communications Commission (FCC) RF Exposure Requirements
SAR compliance has been established in the laptop computer(s) configurations with PCMCIA slot on the side near the center, as tested in the application for certification, and can be used in laptop computer(s) with substantially similar physical dimensions, construction, and electrical and RF characteristics. Use in other devices such as PDAs or lap pads is not authorized. This transmitter is restricted for use with the specific antenna tested in the application for certification. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
R &TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not Intended for Use
None

EU Declaration of Conformity

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU.

WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal.

Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives.

Equipment: 1-port Giga Ethernet PoE Splitter
Model No.: GP-101ST

The following European standards for essential requirements have been followed:
Directives 2014/30/EU
EMC: EN 55032:2015
EN 55024:2010
Directives 2014/35/EU
Safety (LVD) : IEC 62368-1:2014 (2nd Edition) and/or EN 62368-1:2014+A11:2017

Edimax Technology Europe B.V. Fijenhof 2, 5652 AE Eindhoven,
The Netherlands a company of Edimax Technology Co., Ltd. No. 278, Xinhu 1st Rd., Neihu Dist., Taipei City, Taiwan
Printed Name: David Huang
Title: Director
Edimax Technology Europe B.V.

Edimax Technology Co., Ltd.
No. 278, Xinhu 1st Rd., Neihu Dist., Taipei City, Taiwan
Email: support@edimax.com.tw

EDiMAX-GP-101ST-Gigabit-PoE+-Splitter-with-Adjustable-5V-DC-
FIG4