EDiMAX EW-7822ULC Wi-Fi Dongle USB 2.0 1.2 GBit Installation Guide

EDiMAX EW-7822ULC Wi-Fi Dongle USB 2.0 1.2 GBit

Product Information

Package Contents

EW-7822ULC or EW-7822UTC

QIG or CD

System Requirements

• Windows 7/8/8.1~
• Mac OS X 10.7~
• Linux
• USB 2.0 Port
• Hard Disk: 100MB
• CD-ROM Drive

Safety

In order to ensure the safe operation of the device and its users please read and act in accordance with the following safety instructions.
The wireless adapter is designed for indoor use only do not place the wireless adapter outdoors.

1. Do not place the wireless adapter in or near hot humid places  such as a kitchen or bathroom.
2. The wireless adapter contains small parts which are a danger to small children under 3 years old. Please keep the wireless adapter out of reach of children.
3. There are no user-serviceable parts inside the wireless adapter. If you experience problems with the wireless adapter, please contact your dealer of purchase and ask for help.
4. The wireless adapter is an electrical device and as such, if it becomes wet for any reason, stop using it immediately. Contact an experienced electrical technician for further help.

Installation

1. Switch on your computer and insert the USB adapter into an available USB port of your computer.
   Never use force to insert the USB adapter.

2. Insert the included CD-ROM into the CD drive of your computer.

3. The setup wizard is also available for download from the Edimax website.

4. For Windows users the setup wizard will open. For Mac users the CD’s Mac folder will open

5. If the CD doesn’t auto-run or if you downloaded the setup wizard, please browse to the “Autorun” or “Mac” folder of the CD for Windows or Mac users respectively

Windows

Driver Installation
If the CD didn’t auto-run, please open the Autorun.exe file to start the setup wizard.

Click the wireless USB adapter to continue.Click Install Driver to continue.

Click Next to continue.

Please wait while the driver is installing.

You need to restart your computer before using the wireless adapter.

Choose whether to restart your computer now or later, and click Finish.

Click Exit to close the setup wizard.

The multi language QIG is also included on the CD-ROM. To open it click “Multi-language QIG.

7. Please disable any other wireless adapters as described in Disabling Network Adapters. Then Windows users can connect to an available Wi-Fi network as usual. Using The Adapter.

Driver Uninstallation

To uninstall drivers for your adapter, use the Windows Control Panel built in Programs and Features, Uninstall a Program or Add or Remove Programs feature. An example is shown below

Windows 7, 8.1 & 10

1. Open Control Panel using the Start menu or Search function.

2. Select Uninstall a program under the Programs category.
   

3. Select Edimax AC1200 (or similar) and click Uninstall.

Mac OS

Driver Installation

1. Open the RTLWLANU_MacOS  (or similar) folder and double click the Installer.pkg file to open the driver installation wizard.
2. Click “Continue” to proceed to the next step.
3. The next screen displays important information, please read it carefully click “Continue” when you are ready to continue.
4. Select a language the default language is English and click  Continue to install the driver.
5. To read the software license click “Read License” and then click “Agree” to confirm you agree to the terms. You must agree to the terms to continue installing the software.
6. If prompted, select which user to install the software for and click Continue.
7. Click “Install” to install the driver.
8. You may be prompted to enter your system/administrative password before the installation can begin. Enter your password and click Install Software.
9. You will be prompted that you must restart your computer when the installation is complete. Click “Continue Installation” to proceed.
10. Please wait while the driver is installing.
11. When the installation is complete, you will see the following screen informing you that “The installation was successful”. Click  Restart to restart your computer.
12. Next, please disable any other wireless adapters as described in V. Disabling Network Adapters. Then you can connect to a Wi-Fi network as described in VI. Using The Adapter.

Driver Uninstallation

1. Open the “RTLWLANU_MacOS or similar  folder.
2. Double click the Uninstall.pkg file and follow the on-screen instructions.

Disabling Network Adapters

To ensure that your USB wireless adapter can function correctly, it is recommended that you disable any other existing wireless network adapters installed on your computer. If you are unsure how to do so, you can refer to the user manual for your computer, or follow the guidance below.
Using The Adapter
After you have installed the driver and if necessary disabled other wireless adapters Windows users can connect to a Wi-Fi network as usual. Mac users need to connect to a WiFi network using the included utility, as described in VI-2. Mac

Windows
Below is an example of how to connect – the process may vary according to your Windows edition.

1. Click the network icon (examples below) in the system tray and select Connect to a network.
2. Search for the SSID of your Wi-Fi network and then click “Connect”. If you set a password for your network, you will then be prompted to enter it.
3. After correctly entering your password, you will be successfully connected to your Wi-Fi network.

WPS (Wi-Fi Protected Setup) is a simple, alternative way to establish connections between WPS compatible devices. Most modern wireless network devices feature a built-in WPS button, which activates WPS on that device. When WPS is activated in the correct manner and at the correct time for two compatible devices, they will automatically connect to each other. WPS can be activated via the Wi-Fi utility which has the same effect as physically pushing the WPS button known as PBC or push button configuration.
PIN code WPS is an additional variation of WPS which can be activated from a device’s web user interface and includes the use of a PIN code between the two devices for identification and verification.

COPYRIGHT
Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced transmitted transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means electronic mechanical magnetic optical chemical  manual or otherwise without the prior written permission from Edimax Technology Co Ltd. Edimax Technology Co Ltd. makes no representations or warranties, either expressed or implied with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co Ltd reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes. The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device was tested for typical lap held operations with the device contacted directly to the human body to the back side of the notebook computer. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitting antenna during transmitting.

Federal Communications Commission (FCC) RF Exposure Requirements

This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. The equipment version marketed in US is restricted to usage of the channels 1-11 only. This equipment is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.

RED Compliance Statement

Compliance with 2014/53/EU Radio Equipment Directive RED. In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU.

A simplified DoC shall be provided as follows
Hereby Edimax Technology Co  Ltd. declares that the radio equipment type AC1200 Wi-Fi Dual-Band USB Adapter is in compliance with Directive 2014/53/EU
The full text of the EU declaration of conformity is available at the following internet address: http://www.edimax.com/edimax/global/

Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not Intended for Use none.

References

• EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home
• EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home
• EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>