TRANSTEK CB-SL12V-00 Traffic Series Control Box of LED Signal Light Owner’s Manual
- June 1, 2024
- TRANSTEK
Table of Contents
TRANSTEK CB-SL12V-00 Traffic Series Control Box of LED Signal Light
Product Information
Specifications:
- Manufacturer: Transtek LLC
- Product Name: Traffic Series CB-SL12V-00
- Controller Type: Independent
- Developed By: LYAN
- Load Capacity Input: 12V
- Frequency Range: 903.529MHz – 926.471MHz
- Number of Outputs: 2
- Control: LED, IO, button switch
- Channel Division: 16 channels at intervals of 1.529412MHz
Product Usage Instructions
Hardware Introduction – Front View:
- Initiate Start Button: Press to start display status.
- Net Address: Display the current signal channel. Rotate to adjust the channel (1-16). Double press to save the channel.
- Time: Display current time. Rotate to adjust seconds (0-99). Double press to save the time.
- Flash Pattern: Display the current display pattern. Rotate to adjust seconds (1-5). Double press to save the display pattern.
FAQs
-
How do I adjust the display pattern?
To adjust the display pattern, press the Flash Pattern button and rotate left or right to select from patterns 1 to 5. Double press to save the desired pattern. -
How do I change the signal channel?
To change the signal channel, use the Net Address button and rotate left or right to switch between channels 1 to 16. Double-press to save the selected channel. -
What is the frequency range of this controller?
The frequency range of this controller is from 903.529MHz to 926.471MHz, divided into 16 channels at intervals of 1.529412MHz.
Product Profile
CB-SL12V-00 is an independent controller which is developed by LYAN. Control intelligent traffic display equipment, pedestrian right-of-way display, highway fog light…… With powerful processing capacity, and super stability.
Parameters
Load Capacity | 2 output | 12V control LED |
---|---|---|
Input | IO | button switch |
Frequency Range:
| 903.529MHz~926
.471MHz
|
Channel:
| ****
16
| ****
In the range of frequency, it is divided into 16 channels according to the interval of 1.529412MHz
| |
Hardware Introduction
Front View
Introduction
No.| Item|
---|---|---
1| Initiate start button| start display status
2
| ****
Net Address
| Press to display the current signal channel, Rotate to left and right to adjust the channel
( 1-16 ); double press to save the current
channel.
3
| ****
Time
| Press to display the current time,
Rotate to left and right to adjust the seconds
(0-99)
double press to save time.
4
| ****
Flash Pattern
| ****
Press to display the current display pattern, Rotate to left and right to adjust the seconds
(1-5)
double press to save the display pattern.
DIMENSION
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, under Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.