TRANSTEK TMB-2287-B Blood Pressure Monitor User Manual
- June 1, 2024
- TRANSTEK
Table of Contents
- TRANSTEK TMB-2287-B Blood Pressure Monitor
- Product Information
- Product Usage Instructions
- INTRODUCTION
- Features
- Safety Information
- LCD display signal
- BEFORE YOU START
- MEASUREMENT
- DATA MANAGEMENT
- INFORMATION FOR USER
- Maintenance
- ABOUT BLOOD PRESSURE
- TROUBLESHOOTING
- AUTHORIZED COMPONENT
- EMC GUIDANCE
- FCC Statement
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TRANSTEK TMB-2287-B Blood Pressure Monitor
Product Information
Specifications
- Manufacturer: Guangdong Transtek Medical Electronics Co., Ltd.
- Model: TMB-2287-B
- Type: Arm Type Blood Pressure Monitor
- Arm Circumference Range: 22cm to 32cm, 22cm to 42cm, 22cm to 45cm, or 40cm to 52cm
- Measurement Method: Oscillometric
- Warranty Period: 2 years
Product Usage Instructions
Before You Start
- Choice of Power Supply: Ensure to choose the appropriate power supply option.
- Installing and Replacing the Batteries: Follow the manual instructions to install or replace batteries.
- Setting Date and Time: Set the date and time on the monitor.
- Pairing a Smart Device: Pair a smart device with the monitor if needed.
- Setting a User ID: Set a user ID for personalized tracking.
Measurement
- Applying the Cuff: Place the cuff around the arm within the specified circumference range.
- Start the Measurement: Initiate the measurement process following the monitor’s instructions.
Data Management
- Recalling Records: Retrieve stored records for review.
- Deleting Records: Clear records as needed.
Information for User
- Tips for Measurement: Follow the provided tips for accurate measurements.
- Maintenance: Learn about maintenance practices to ensure product longevity.
About Blood Pressure
- Systolic and Diastolic Pressure: Understand the meaning of these blood pressure readings.
- Blood Pressure Classification: Learn about standard blood pressure categories.
- Pulse Rate Detector: Know about irregular pulse rate detection feature.
- Blood Pressure Fluctuations: Understand reasons for blood pressure variations throughout the day.
- Differences in Readings: Learn about variations in readings between home and hospital measurements.
- Arm Selection: Address whether results differ based on measuring arm.
Frequently Asked Questions (FAQ)
-
How often should I measure my blood pressure?
We recommend measuring your blood pressure at least once a day at a consistent time for accurate tracking. -
Can multiple users store their data on the monitor?
Yes, you can set up different user IDs for multiple users to store and track their individual measurements. -
What does an irregular pulse rate indicate?
An irregular pulse rate may suggest underlying health conditions, and it is recommended to consult a healthcare professional for further evaluation.
User Manual
Blood Pressure Monitor Model:TMB-2287-B
- Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-2287-B.
- Please do read the user manual carefully and thoroughtly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems.
INTRODUCTION
General Description
Thank you for selecting TRANSTEK blood pressure Monitor (TMB-2287-B). The
monitor features blood pressure measurement, pulse rate measurement and the
result storage. The warranty period is two years.
Readings taken by the TMB-2287-B are equivalent to those obtained by a trained
observer using the cuff and stethoscope auscultation method.
This manual contains important safety and care information, and provides step
by step instructions for using the product.
Read the manual thoroughly before using the product.
Features
60.5 mm×92.5 mm Digital LCD display
Maximum 199 records per user
Measuring-during-inflation technology
Indications for Use
This Blood Pressure Monitor is a digital monitor intended for use in measuring
blood pressure and pulse rate with arm circumference ranging from 22cm to 32cm
(about 8¾-12½2), 22cm to 42cm (about 8¾”-16/), 22cm to 45cm (about 8¾”-17¾)
or 40cm to 52cm (about 15¾”-20½). It is intended for adult indoor use only.
Measurement Principle
This product uses the Oscillometric Measuring method to detect blood pressure.
Before every measurement, the unit establishes a “zero pressure” equivalent to
the airpressure. Then it starts inflating the arm cuff, meanwhile, the unit
detects pressure oscillations generated by beat-to-beat pulsatile, which is
used to determine the systolic and diastolic pressure, and also pulse rate.
Receiving and Inspecting your Monitor
Check that the device packaging has not been tampered with and make sure that
all contents are present. Before use, ensure that there is no visible damage
to the device or accessories and that all packaging material has been removed.
If you have any doubts, do not use the device and contact your retailer or the
specified Customer Services address.
Safety Information
The signs below might be in the user manual, labeling or other component. They are the requirement of standard and using.
Precaution
-
This device is intended for indoor, home use and is not intended for self-use in public areas.
-
This device is portable, but it is not intended for use during patient transport.
-
This device is not suitable for continuous monitoring during medical emergencies or operations.
-
This device is intended for non-invasive measuring and monitoring of arterial blood pressure.
It is not intended for use on extremities other than the arm, or for any purpose other than obtaining a blood pressure measurement. -
This device is for adults. Do not use this device on neonates or infants. Do not use it on children and adolescents unless otherwise instructed by a medical professional.
-
Consult with your physician before using this monitor if you suffer from the following conditions: common arrhythmias such as premature ventricular beats or atrial fibrillation;
peripheral arterial disease; pregnancy; preeclampsia; implantation with electrical devices; undergoing intravascular therapy; arteriovenous shunt or mastectomy. -
Please note that any of these conditions may affect measurement readings, in addition to patient motion, trembling or shivering.
-
Do not use this device for diagnosis or treatment of any health problems or diseases. Please consult with your physician first whether the blood pressure or pulse rate readings can be used as an input in determining clinical actions. Please note that clinical actions can only be determined by the physician, otherwise it may lead to delayed treatment or other dangerous situations.
-
If you are taking medication, consult your physician to determine the proper time to measure your blood pressure.
-
This device may be used only for the intended use described in this manual, the manufacturer shall have no liability for any incidental, consequential, or special damages caused by misuse or abuse.
-
Please use the device under the environment which is provided in the user manual. Otherwise, the performance and lifetime of the device will be impacted and reduced.
-
The device may require up to 30 minutes to warm up / cool down from the minimum/ maximum storage temperature before it is ready for use.
-
The blood pressure monitor, its adapter, and the cuff are suitable for use within the patient environment.
-
Do not wash the cuff in a washing machine or dishwasher !
-
The device contains sensitive electronic components. To avoid measurement errors, avoid taking blood pressure measurements near a strong electromagnetic field radiated interference signal or electrical fast transient/burst signal.
-
Wireless communication equipment, such as wireless home network devices, mobile phones, cordless telephones and their base stations, walkie-talkies may cause interference that may affect the accuracy of measurements. A minimum distance of 1 foot (30 cm) should be kept from such devices durina a measurement.
-
Blood Pressure Monitor is intended for use by medical staff and lay persons, and patient is also an intended user or operater.
Caution
- Do not attempt to repair the unit yourself if it malfunctions. Only have repairs carried out by authorized service centers.
- It is recommended that the performance should be checked after repair, maintenance, and every two years of use, by retesting the requirements in limits of the error of the cuff pressure indication and air leakage (testing at least at 50 mmHg and 200 mmHg). Please contact manufacturer or distributor for authorized service personnel.
- Store your device, cuff and adapter in a clean and dry place, protect it against extreme moisture, heat, lint, dust and direct sunlight. Never place any heavy objects on it.
- Make sure the rubber tube of the cuff is not squeezed, stretched, or kinked during storage.
- Dispose of accessories, detachable parts, and the device according to the local guidelines.
Warning
- Do not apply the cuff on an arm that has an intravenous drip or a blood transfusion attached.
- Do not kink, fold, stretch, compress, or otherwise deform the tube during measuring, as the cuff pressure might continuously increase, which could prevent blood flow and result injury.
- Taking blood pressure measurements too frequently could disrupt blood circulation and cause injuries.
- Do not apply cuff to areas on patient where skin is delicate or damaged. Check cuff site frequently for irritation.
- Do not place the cuff on the arm of a person whose arteries or veins are undergoing medical treatment, i.e. intra-vascular access or intra-vascular therapy or an arteriovenous (A-V) shunt, which could disrupt blood circulation and cause injuries.
- Do not place the cuff on the arm on the same side of a mastectomy (especially when lymph nodes have been removed). it is recommended to take measurements on the unaffected side. Do not wrap the cuff on the same arm to which another monitoring device is applied. One or both devices could temporarily stop functioning if you try to use them at the same time. Please check (for example, by observation of the limb concerned) that the operation of the device does not result in prolonged impairment of patient blood circulation.
- On the rare occasion of a fault causing the cuff to remain fully inflated during measurement, loosen and remove the cuff immediately. Prolonged high pressure applied to the arm (cuff pressure >300 mmHg or constant pressure >15 mmHg for more than 3 minutes) might lead to bruising and discolored skin.
- Do not use this device with high-frequency (HF) surgical equipment at the same time.
- This device is not used in conjunction with oxygen rich environments, not intended for use with flammable anaesthetics, not intended for use in conjunction with flammable agents.
- Do not touch output of the batteries/adapter and the user simultaneously.
- The power cord is considered the disconnect device for isolating this equipment from supply mains. Do not position the equipment so that it is difficult to reach or disconnect.
- Do not use this device if you are allergic to polyester, nylon, or plastic. * Only use accessories approved by manufacturer. Using unapproved accessories might cause damage to the unit and injure users.
- If you experience discomfort during a measurement, such as pain in the arm or other complaints, press the Power button immediately to release the air from the cuff.
- Do not use the device while under maintenance, or being serviced.
- The air tube poses a risk of strangulation. Furthermore, the small parts of product and batteries present a choking hazard if swallowed. They should therefore always be kept away from infants/children.
- Sensor degradation or looseness may reduce performance of device or cause other problems.
Notice
-
You can use this device to take your own measurement, no third-party operator is required.
-
Adapter is specified as a part of ME EQUIPMENT.
-
At the request of authorized service personnel, circuit diagrams, component part lists, descriptions, and calibration procedures will be made available by the manufacturer or distributor.
-
The expected lifetime of the cuff may vary by the frequency of washing, skin condition,
and storage state. -
Please report to the manufacturer and the competent authority of the Member State / the FDA in which you are established about any serious incident that has occurred in relation to this device.
LCD display signal
Monitor Components
List
BEFORE YOU START
Choice of Power Supply
- Battery powered mode: 6VDC 4xAAA batteries
- AC adaptor powered mode: 5V 1A (Optional!) (Please use the AC adapter which is authorized by the manufacturer!) Please unplug the adaptor to depart from the using utility power.
CAUTION
In order to get the best effect and protect your monitor,please use the the
right batteries and special power adapter which complies with local safety
standard.
Installing and Replacing the Batteries
- Open the battery cover.
- Install the batteries by matching the correct polarity, as shown.
- Replace the battery cover.
Replace the batteries whenever the below happens
- The bAt Lo shows.
- The display is dim.
- The display does not light up.
CAUTION
- New and used batteries, or different types of batteries shall not be used together.
- Remove batteries if the device is not likely to be used for some time.
- Do not heat or deform the batteries, or dispose of them in fire.
- Batteries should not be disposed of with household waste.
- Please check with your local authority for battery recycling advice.
Setting Date and Time
It is important to set the clock before using your blood pressure monitor, so
that a time stamp can be assigned to each record that is stored in the memory.
(The setting range of the year :2023-2053 time format:12H/24H)
-
When the monitor is off, press and hold the “SET” button, it will display the bluetooth symbol first.
No operation within 60s or Press “START•STOP” button, it will skip Bluetooth pairing and enter the [Year] setting. -
Press “MEM” or “SET” button to change the [Year].
Each press will increase or decrease the numeral by one in a cycling manner. -
When you get the right year, press “START•STOP” button to set down and turn to next step.
Repeat the same steps to set the date format between [month/day] and [day/month]. -
Repeat the same steps to set the [Month] and [Day].
-
Repeat the same steps to set the time format between 24H and 12H.
-
Repeat the same steps to set the [Hour] and [Minute].
-
After the [Minute] is set,the LCD will display “do nE”, and then it will turn off automatically.
Pair a smart device with the monitor
You are the intended operator of this blood pressure monitor. You can measure
your blood pressure and then save and send measurement data to a smart device
(such as smartphone or tablet) with Bluetooth wireless connectivity.
- Turn on Bluetooth and the app on your smart device. Make sure both are ON when pair-up is proceeding.
- When the monitor is off, press and hold the “MEM” button to start pair-up, the bluetooth symbol will flash. If successful, the bluetooth symbol will not flash any more and the monitor will display “do nE”, and then it will shut off after about several seconds automatically.
Note
- The date and time on your monitor will automatically be set after paired with your smart device successfully.
- The device can also enter the Bluetooth pairing automatically when the battery is installed for the first time.
If unsuccessful within 60 seconds, it is judged timeout and the monitor will shut off.
Specifications for Bluetooth Transmission
Bluetooth| Throughput| 2.5K-5K
Latency| 50ms
Error Rate| 0 when≥–70dBm
Operating Frequency| 2402-2480MHz
Transmission Power| see test report
Transmission Distance| 10m
Note:
- The necessary Quality of Service (QoS) is fully considered here for wirelessly enabled functions.
- Interference may occur in the vicinity of equipment marked with the following symbol . And TMB-2287-B may interfere the vicinal electrical equipment.
- Keep the monitor at least 20 centimeters away from the human body (especially the head) when data transmission is proceeding after measurement.
- To enable the data transmission function, this device shall be paired to an appropriate BT mobile terminal.
Warning
About a wireless communication interference
The monitor operates in the unlicensed ISM band at 2.4 GHz. In case it is used
around the other wireless devices including microwave and wireless LAN, which
operate at the same frequency band as the monitor, there is a possibility that
interference occurs between the monitor and such other devices. If such
interference occurs, please stop the operation of other devices or relocate
the monitor before using it or do not use it around the other wireless
devices.
- List of compatible devices:
- For iOS devices:
- The operating system must be iOS 13.0 or more.
- For Android devices:
- The operating system must be Android 5.0 or more.
Setting a user ID
There are 2 user ID , each with 199 memory spaces, are designed for 2 different people to save the measured values separately.
- When the monitor is off, Switch “USER” button to select the user ID between the user .
- Press “START•STOP” button to confirm the selected user ID, the monitor will enter the measurement automatically.
Press “MEM” button to confirm the selected user ID, the monitor will enter the memory query automatically.
Note:
You can select User A or User B by switching the “USER” button during the
process of measurement or when it is in the memory mode.
MEASUREMENT
Applying the cuff
Only use a cuff that has been approved by the manufacturer for this device
model. Before use, please confirm if it fits your arm circumference.
-
Remove all jewelry, such as watches and bracelets from your left arm.
Note : If your doctor has diagnosed you with poor circulation in your left arm, use your right arm. -
Roll or push up your sleeve to expose the skin. Make sure your sleeve is not too tight.
-
Hold your arm with your palm facing up and tie the cuff on your upper arm, align the Artery indicator with the main Artery (on the inside of your arm).
Note : Locate the main Artery by pressing with 2 fingers approximately 2 cm above the bend of your elbow on the inside of your left arm. Identify where the pulse can be felt the strongest, that is your main Artery! -
Make sure the bottom edge of the arm cuff 2 to 3 cm above the inside elbow. Then wrap the cuff securely.
Note : The cuff should be snug but not too tight.
You should be able to insert one finger between the cuff and your arm. -
Sit upright in a comfortable chair with your back against the backrest of the chair. Keep your feet flat and your legs uncrossed.
Place your arm resting comfortably on a flat table. The cuff worn on your arm should be placed at the same level as your right atrium of the heart. -
Take 5-6 deep breaths and let’s start measuring!
Helpful tips:- Take the measurement in a silent room.
- Rest for 5 minutes before a measurement.
- Wait at least 3 minutes before another measurement.
- This allows your blood circulation to recover.
- Be relaxed and do not move and talk during the measurement procedure.
- For a meaningful comparison, try to measure under similar conditions. For example, take daily measurements at approximately the same time, on the same arm, or as directed by a physician.
Start the Measurement
-
When the monitor is off, press “START•STOP” button to turn on the monitor, and it will finish the whole measurement. (Take User A for example.)
-
Press “START•STOP” button to power off, otherwise it will turn off within 1 minute. Note
Any time, to stop the measurement, press “START•STOP ” button.
If you don’t pair with the device or don’t keep the app ON, the bluetooth symbol will flash during the measurement. -
If your monitor is already paired with your smart device and both Bluetooth and app are ON, when the measurement completed, the measurement result will start transmitting. (only User A and B available) If successful, the symbol “ ” will disappear first, after sevral seconds, “ ‘” will also disappear, and then the monitor will turn off automatically.lly.If unsuccessful within 60 seconds, it is judged timeout and the monitor will shut off. In the case of a data transmission failure, up to 199 measurements are saved on the device and will be sent when a successful connection is achieved.
-
About the irregular pulse rate and excessive body motion during the measurement.
During a measurement, If an irregular pulse rate is detected, the symbol will display in the measurement result. See page 24 for more information.
During a measurement, when the excessive body motion, the symbol will flash about 5 seconds and detect again. If it is no longer detected, the symbol will disappear; If still detected, the symbol will final display in the measurement result.
Note
The measured blood pressure reading may not be accurate if this symbol is displayed.
Recall the Records
- When the monitor is off, press “MEM” button, the user ID will blink.
- You can switch “USER” button to select the user ID between user A and press “START•STOP” button to confirm the selected user ID.
- Then the LCD will display the average value of last 3 readings. When the records are less than three groups, it will display the latest record. (Example shown below for User A)
- Press “MEM” or “SET” button to display the next record.
Note
- If there is untransmitted data, the symbol * will display on the record.
- The latest record (1) is shown first. Each new measurement is assigned to the first (‘ record. All other records are pushed back one digit (e.g., 2 becomes 3, and so on), and the last record (199) will be dropped from the list.
- When you pass the limit, every time you recall the records, the monitor will display “FULL” along with the group number “199”.9”.
DATA MANAGEMENT
Delete the Records
If you did not get the correct measurement, you can delete results by
following steps below.
A: To delete a single measurement:
- Enter the memory recall mode as described in section [Recall the Records]. Pres “MEM” or “SET” button to get the measurement you would like to erase.
- Press and hold “MEM” button for about 5 seconds, and the display will show a blinking “dEL y”.
- Use “MEM” or “SET” button to switch between “dEL y” and “dEL no”, Press “START•STOP” to confirm the selection.
If “dEL y” is selected, the LCD will display “do nE”, and then the previous
record will be displayed.
If “dEL no” is selected, it will stop the deletion.
B: To delete all measurements:
- Enter the memory recall mode as described in section [Recall the Records].
- Press and hold “MEM” and “SET” button button for 5 seconds, and the display will show a blinking “dEL AL” along with the user ID.
- Use “MEM” or “SET” button to switch between “dEL AL” and “dEL no”, Press “START/STOP” to confirm the selection.
If “dEL AL” is selected, the LCD will display “do nE” , and delete all the record of the current user. Several seconds later, it will display “—”. If “dEL no” is selected, it will stop the deletion.
INFORMATION FOR USER
Tips for Measurement
Measurements may be inaccurate if taken in the following circumstances
.
Maintenance
In order to get the best performance, please follow the instructions below.
- Cleaning Process:
- Step 1: Make sure to switch off and unplug the device prior to cleaning.
- Step 2 : Use a soft cloth wetted with soapy water to clean the cuff first, and then use a soft cloth wetted with clear water to remove residual soap until there is no visible residual contaminants. Attention shall be paid to avoid liquid invasion into the cuff.
- Step 3 : Use a dry soft cloth to wipe the cuff, in order to remove residual moisture.
- Step 4 : Dry the cuff at a well-ventilated place after cleaning.
- Disinfection Process
- Step 1 : Make sure to switch off and unplug the device prior to disinfection.
- Step 2 : Use a soft cloth wetted with 70% isopropanol to disinfect the cuff for about 10 minutes. Attention shall be paid to avoid liquid invasion into the cuff.
- Step 3 : Use a clean dry cloth or towel to wipe off the disinfectant until there is no visible residue.
- Step 4 : Dry the cuff at a well-ventilated place after disinfection.
Suggestion
Frequency of Cleaning and Disinfection:
For single patient multiple use, it’s recommended to clean the device surface
once a month or whenever it’s necessary.
For multiple patient multiple use, it’s recommended to clean the device every
time before and after usage. Maintenance procedures shall be taken as per
instruction.
ABOUT BLOOD PRESSURE
What are systolic pressure and diastolic pressure?
When ventricles contract and pump blood out of the heart, the blood pressure
reaches its maximum value in the cycle, which is called systolic pressure.
When the ventricles relax, the blood pressure reaches its minimum value in the
cycle, which is called diastolic pressure.
What is the standard blood pressure classification?
The blood pressure classification published by World Health Organization (WHO)
and International Society of Hypertension (ISH) in 1999 is as follows:
Irregular Pulse Rate Detector
An irregular pulse rate will be detected if there is an irregular pulse rhythm
while measuring systolic and diastolic blood pressure. When measurements were
performed, the monitor will record all pulse intervals and calculate the
average. If two or more pulse intervals were recorded, and the difference
between each interval and the average is larger than ±25% of the average; or
if four or more pulse intervals were recorded, and the difference between each
interval and the average is larger than ±15% of the average value, the
irregular pulse symbol will be displayed along with measurement results.
CAUTION
The appearance of the IPR icon indicates that a pulse irregularity consistent
with an irregular pulse rate was detected during measurement. Usually this is
NOT a cause for concern. However, if the symbol appears often, we recommend
you seek medical advice. Please note that the irregular pulse rate detector
only serves as a non-medical feature, and the results cannot be used directly
for clinical judgement. Please seek medical advice from professionals before
making any medical decisions.
Why does my blood pressure fluctuate throughout the day?
- Individual blood pressure varies multiple times everyday. It is also affected by the way you tie your cuff and your measurement position, so please take the measurement under the same conditions.
- If the person takes medicine, the pressure will vary more.
- Wait at least 3 minutes for another measurement.
Why do I get a different blood pressure at home compared to the hospital?
The blood pressure is different even throughout the day due to weather,
emotion, exercise etc, Also, there is the “white coat” effect, which means
blood pressure usually increases in clinical settings.
Is the result the same if measuring on the right arm?
It is ok for both arms, but there will be some different results for different
people. We suggest you measure the same arm every time.
What you need to pay attention to when you measure your blood pressure at
home
If the cuff is tied properly.
If the cuff is too tight or too loose. If the cuff is tied on the upper arm.
If you feel anxious.
Taking 2-3 deep breaths before beginning will be better for measuring.
Advice: Relax yourself for 4-5 minutes until you calm down.
TROUBLESHOOTING
If any abnormality arises during use, please check the following points:
PROBLEM | SYMPTOM | CHECK THIS | REMEDY |
---|---|---|---|
No power | Display can not light up. | Batteries are depleted. | Replace |
with new batteries.
Batteries are inserted incorrectly.| Insert the batteries correctly.
Adapter is inserted incorrectly.| Insert the AC adapter correctly.
High Battery| bAt H shows| The battery is too high.| Replace with new
batteries.
Low Battery| bAt Lo & shows| The battery is too low.| Replace with new
batteries.
Error message
| E 1 shows| The cuff is not wrapped or wrapped incorrectly, or the cuff air
plug is loose.| Refasten the cuff and insert air tube plug correctly then
measure again.
E 2 or shows| Excessive body motion (such as shaking of the arm with the cuff
on) or weak pulse is detected.| Relax for 5 minutes. and then keep still,
measure again.
E 3 shows| Pulse is not detected during measuring.| Loosen the clothing on the
arm and measure again.
E 4 shows| The measurement failed.| Relax for 5 minutes and measure again.
EEx shows| Hardware error (X can be some digital symbol, such as1, 2, etc.)|
Turn off monitor and measure again. If EEx still appears on the display,
please contact the retailer or our customer service.
USb Err shows| The voltage of the adapter is too high or too low.| Replace
with the authorized adapter.
Warning message| out shows| Out of measurement range| Relax for a moment
and then measure again. If the problem persists, contact your physician.
NOTE: If the product still does not work, contact Customer Service. Under no circumstance should you disassemble or attempt to repair the unit by yourself.
Power supply
| Battery powered mode: 6VDC 4*AAA batteries AC adaptor powered mode: 5V 1A
(Please use the AC adapter which is authorized
by the manufacturer!)
---|---
Display mode| Digital LCD V.A.60.5 mm × 92.5 mm
Measurement mode| Oscillographic testing mode
Measurement range|
- Rated cuff pressure: 0mmHg~299mmHg Measurement pressure:
- SYS: 60mmHg~230mmHg DIA: 40mmHg~130mmHg
- Pulse value: (40-199)beat/minute
Accuracy|
- Static Pressure: 5℃-40℃ within ±3mmHg Pulse value: ±5%
- Clinical validation: Mean difference within ±5mmHg;
- Standard deviation ::8mmHg
Normal working condition|
- A temperature range of: +5°C to +40°C A relative humidity range of 15% to 90%, non-condensing, but notrequiring a water vapour partial pressure greater than 50 hPa
- An atmospheric pressure range of 700 hPa to 1060 hPa
Storage & transportation condition|
- Temperature:-20°C to +60°C
- A relative humidity range of :: 93%, non-condensing, at a water vapour pressure up to 50 hPa
- An atmospheric pressure range of 500 hPa to 1060 hPa
Measurement perimeter of the upper arm| About 22cm-32cm or 22cm-42cm or
22cm-45cm or 40cm-52cm
Net Weight| Approx.275g(Excluding the dry cells and cuff)
External dimensions| Approx.140mm×130mm×55.6mm
Mode of operation| Continuous operation
Degree of protection| Type BF applied part
Protection against ingress of water| IP21 It means the device could be
protected against solid foreign objects of 12,5mm <l and greater, and against
vertically falling water drops.
Device Classification|
- Battery Powered Mode:
- Internally Powered ME Equipment AC Adaptor Powered Mode: Class II ME Equipment
Software Version| A01
Expected Lifetime|
- Device: 3 years or 30,000 measurements (may vary based on usage conditions)
- Cuff: 10000 times
- Alkaline battery: About 200-300 times
Types of use/reuse| Multiple patient multiple use
WARNING: No modification of this equipment is allowed.
AUTHORIZED COMPONENT
Authorized Component
Please use the authorized adapter.(Optional!)
Contact Information
For more information about our products, please visit
www.transtekcorp.com.
Manufactured by: Guangdong Transtek Medical Electronics Co., Ltd.
Company: Guangdong Transtek Medical Electronics Co., Ltd.
Address: Zone A, No.105, Dongli Road, Torch Development District, 528437
Zhongshan, Guangdong, China
EMC Guidance
The ME EQUIPMENT or ME SYSTEM is suitable for home healthcare environments.
Essential performance
Accuracy of measuring blood pressure and pulse rate
Measurement Range| Systolic pressure: 60-230 mmHg Diastolic pressure: 40-130
mmHg Pulse: 40-199 beats/minute
---|---
Rated Cuff Pressure| 0-299 mmHg (0-39.9 kPa)
Accuracy|
- Static Pressure: 5℃-40℃ within ±3mmHg Pulse value: ±5%
- Clinical validation: Mean difference within ±5mmHg;
- Standard deviation ::8mmHg
The Basis Safety of the Blood Pressure Monitor (TMB-2287-B) is as following: Deviation from normal operation that poses an unacceptable risk to the patient or operator.
Warning: Don’t be near the active HF surgical equipment and the RF
shielded room of an ME system for magnetic resonance imaging, where the
intensity of EM disturbances is high.
Warning: Use of this equipment adjacent to or stacked with other
equipment should be avoided because it could result in improper operation. If
such use is necessary, this equipment and the other equipment should be
observed to verify that they are operating normally.
Warning: Use of accessories, transducers and cables other than those
specified or provided by the manufacturer of this equipment could result in
increased electromagnetic emissions or decreased electromagnetic immunity of
this equipment and result in improper operation.
Warning: Portable RF communications equipment (including peripherals such
as antenna cables and external antennas) should be used no closer than 30 cm
(12 inches) to any part of the equipment including cables specified by the
manufacturer. Otherwise, degradation of the performance of this equipment
could result.
EMC GUIDANCE
Technical description
- all necessary instructions for maintaining BASIC SAFETY and ESSENTIAL PERFORMANCE with regard to electromagnetic disturbances for the expected lifetime.
- Guidance and manufacturer’s declaration -electromagnetic emissions and Immunity
Table 1
Guidance and manufacturer’s declaration – electromagnetic emissions
Emissions test| Compliance
RF emissions CISPR 11| Group 1
RF emissions CISPR 11| Class [ B ]
Harmonic emissions IEC 61000-3-2| Class A
Voltage fluctuations / flicker emissions
IEC 61000-3-3
| Comply
Table 2
Guidance and manufacturer’s declaration – electromagnetic Immunity
Immunity Test| IEC 60601-1-2
Test level
|
Compliance level
Electrostatic discharge (ESD) IEC 61000-4-2
|
±8 kV contact
±2 kV, ±4 kV, ±8 kV, ±15 kV air
|
±8 kV contact
±2 kV, ±4 kV, ±8 kV, ±15 kV air
Electrical fast transient/burst IEC 61000-4-4| ±2 kV for power supply lines
±1 kV signal input/output 100 kHz repetition frequency
| ±2 kV for power supply lines Not applicable
100 kHz repetition frequency
Surge IEC61000-4-5| ±0.5 kV, ±1 kV differential mode
±0.5 kV, ±1 kV, ±2 kV common mode
| ±0.5 kV, ±1 kV differential mode Not applicable
Voltage dips, short interruptions and voltage variations on power supply input
lines
IEC 61000-4-11
| 0% UT; 0,5 cycle. At 0°, 45°, 90°, 135°,
180°, 225°, 270° and 315°.
0% UT; 1 cycle and 70% UT; 25/30 cycles; Single phase: at 0°. 0% UT; 250 / 300 cycle
| 0% UT; 0,5 cycle. At 0°, 45°, 90°, 135°,
180°, 225°, 270° and 315°.
0% UT; 1 cycle and 70% UT; 25/30 cycles; Single phase: at 0°. 0% UT; 250 / 300 cycle
Power frequency magnetic field IEC 61000-4-8| 30 A/m
50 Hz / 60 Hz
| 30 A/m
50 Hz / 60 Hz
Conduced RF IEC61000-4-6
| 3 V
0,15 MHz – 80 MHz
6 V in ISM and amateur radio bands between 0,15 MHz and 80 MHz
80% AM at 1 kHz
| 3 V
0,15 MHz – 80 MHz
6 V in ISM and amateur radio bands between 0,15 MHz and 80 MHz
80% AM at 1 kHz
Radiated RF IEC61000-4-3
| 10 V/m
80 MHz – 2,7 GHz
80% AM at 1 kHz
| 10 V/m
80 MHz – 2,7 GHz
80% AM at 1 kHz
NOTE UT is the a.c. mains voltage prior to application of the test level.
Table 3
Guidance and manufacturer’s declaration – electromagnetic Immunity
Radiated RF IEC61000-4-3
(Test specifications for ENCLOSURE PORT IMMUNITY to
RF wireless communica- tions equipment)
| Test Frequency (MHz)| Band
(MHz)
| Service| Modulation| Modulation Power
(W)
| Distance
(m)
| IMMUNITY TEST LEVEL
(V/m)
| Compliance level
(V/m)
385| 380-390| TETRA 400| Pulse modulation
18Hz
| 1.8| 0.3| 27| 27
450
|
430-470
| GMRS 460,FRS
460
| FM ± 5kHz
deviation 1kHz sine
|
2
|
0.3
|
28
|
28
710| 704-787| LTE Band 13,17| Pulse modulation 217Hz|
0.2
|
0.3
|
9
|
9
745
780
810| 800-960| GSM 800/900, TETRA 800,
iDEN 820,
CDMA 850,
LTE Band 5
| Pulse modulation 18Hz| 2| 0.3| 28| 28
870
930
1720|
1700-
1990
| GSM 1800;
CDMA 1900;
GSM 1900; DECT;
LTE Band 1,
3,
4,25; UMTS
| Pulse modulation 217Hz|
2
|
0.3
|
28
|
28
1845
1970
2450| 2400-
2570
| Bluetooth, WLAN, 802.11
b/g/n, RFID 2450, LTE
Band 7
| Pulse modulation 217 Hz|
2
|
0.3
|
28
|
28
5240|
5100-
5800
| WLAN 802.11
a/n
| Pulse modulation 217 Hz|
0.2
|
0.3
|
9
|
9
5500
5785
FCC Statement
FCC ID: OU9-TMB2287B
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Regulatory Compliance
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>