LNC W13 Farmhouse Chandeliers for Dining Rooms with Faux Wood Finish Instruction Manual
- June 1, 2024
- LNC
Table of Contents
LNC W13 Farmhouse Chandeliers for Dining Rooms with Faux Wood Finish
Product Information
Specifications:
- Parts Included: Single bar, Green ground screw, Canopy, Collar ring, Collar loop, Quick link, Chain, Loop, Disk, Arm, Upper frame, Tube, Stem, Screw, Fixture loop assembly, Lower frame
- Accessories Included: Wire connector, Mounting screw
Product Usage Instructions
Assembly & Installation Instructions:
- Carefully remove all parts and accessories from the packaging.
- Follow the steps below for assembly:
- Screw the disk and fixture loop assembly together with a tube.
- Connect the upper frame and lower frame together with a stem and screws.
- Twist the loop on top of the disk.
- Determine the correct number of links needed for hanging height and adjust the chain accordingly.
- Connect the chain to the loop on top of the disk using a quick link.
- Lace the wires through the chain and stop just before reaching the top.
- Turn off power before starting installation.
- Install the fixture following these steps:
- Attach the single bar to the outlet box with mounting screws.
- Secure the canopy over the mounted collar loop to test the height.
- Slip the collar ring over the chain and canopy.
- Attach the quick link to connect the loop.
- Cut off any excess wire length if necessary.
FAQs
Q: Can I install this product without a licensed electrician?
A: It is recommended to have a licensed electrician perform the installation for safety reasons.
Q: How do I adjust the hanging height of the fixture?
A: Follow the instructions provided to adjust the number of links in the chain for proper hanging height.
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF”
- ition.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
TOOLS REQUIRED
(NOT INCLUDED)
Before doing assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDING
- (C) Single bar (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Collar ring (1)
- (G) Collar loop (1)
- (H) Quick link (2)
- (I) Chain (1)
- (J) Loop(1)
- (K) Disk (1)
- (L) Arm (3)
- (M) Upper frame (1)
- (N) Tube (1)
- (O) Stem (3)
- (P) Screw (6)
- (Q) Fixture loop assembly (1)
- (R) Lower frame (1)
ACCESSORIES & QTY ENCLOSED:
- (A) Wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
* Step A1: Screw the disk (K) and the fixture loop assembly (Q) together with a tube (N).
* Step A2: Connect the upper frame (M) and the lower frame (R) together with a stem (O) and fix them with screws (P). Step A3: Twist the loop(J) on top of the disk (K).
* Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
* Step B2: Attach the quick link (H) to connect the chain (I) and the loop(J) on the the top of sidk (K).
* Step B3: Carefully lace the wires through the chain (I)(every other link)and stop just before you reach the top of chain (I).Gently pull the wires till snug.-
Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF”
position. B).Place the wall switch in the“OFF” position. -
Make installation
* Step C1: Remove the collar ring (F) from collar loop(G). Attach the single bar (C) to outlet box with mounting screws (B). The side of single bar marked “GND” must face out, Unscrew the collar ring (F) from the collar loop.
* Step C2: Pass canopy (E) over the mounted collar loop (G) then secure with collar ring (F) to test the height . Unscrew the collar ring (H) from the collar loop.
Note: The canopy (E) should be snug against the ceiling and the collar loop
(F) should be screwed enough threads (no less than 6 threads )over the
threaded nipple for more secure hanging .If not, adjust the height of nipple
and collar loop (G) until the desired height is reached. Remove the collar
ring (F) and canopy (E) and place to the side.
* Step C3: Slip the collar ring(F) over the chain(I),then do the same with the canopy(E).
* Step C4: Open the quick link(H)，attach the quick link (H) to connect the loop (G). Close the quick link(H) Pass the wires through screw collar loop(G) to the top of nippleand gently pull till snug.
* Step C5: If needed, cut off the wires length of fixture.At this point, the remaining wire length measured from the top single bar(C) is at least 6″.
* StepC6: Make wire connections Connect wires as below wires connecting shown.TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
Twist plastic wire connector until wires are tightly joined together,wrap each
connector with approved electrical tape.Be sure that no wire strands are
exposed and then carefully tuck all wires into the outlet box .
* Step C7: Raise canopy (E) to ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).
* Step C8: Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.)- Check everything is already installed properly, then you could turn on the light. Enjoy!
CLEANING.
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such
as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>