LNC HA0517401 Iatreia 24.6-in W 1-Light Plating Brass Instruction Manual
- June 1, 2024
- LNC
Table of Contents
LNC HA0517401 Iatreia 24.6-in W 1-Light Plating Brass
WARNING
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is LED, 12W.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture.
|
|
|
|
---|---|---|---|---
Ladder| Philips Head or Flat
Blade Screwdriver| Electrical Tape| Pliers| Wire Cutter/Stripper
PARTS INCLUDED
(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Canopy screw (4)
(G) Frame (1)
(H) Glass (2)
(I) Gasket (4)
(J) Screw (4)
ACCESSORIES ENCLOSED
(A) Mounting screw (2)
(B) Plastic wire connector (3)
(I) Gasket (1) (spare part)
(J) Screw (1) (spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Make assembly
Step A1 » Unscrew canopy screws (F) from canopy (E) and mounting plate (C), then set them aside for later installation.
Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
Step A3 » Make wire connections Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
Connect wires according to the chart below
**** Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is
square shaped or ridged and the other wire will be round in shape or smooth
(see illus.)
Twist wires together with plastic wire connectors (B) until tightly joined,
and wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in canopy (E) with the pre-assembled mounting
screws, then attach canopy (E) to mounting plate (C) with the previously
removed canopy screws (F). Hand tighten until snug.
NOTE: Canopy(E) should be snug against the wall with canopy screws (F).
If not, remove canopy (E), adjust the threaded length of pre-assembled
mounting screws on mounting plate (C):
* Unscrew the pre-assembled hex nuts.
* Screw the pre-assembled mounting screws in or out of mounting plate (C).
* When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
Step A5 » Align holes of frame (G) and holes of glasses (H), and then screw screws (J) through gaskets (I) into holes as shown in the illustration.
- Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Customer Support
+1 8638672245
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>