EUROLAMP 300-25017(S36-32) Ceiling Fan with LED Light Instructions
- June 12, 2024
- EUROLAMP
Table of Contents
Pioneers in New Technology !
INSTRACTION
300-25017(S36-32)
DECORATIVE FAN WHITE WITH LED LIGHT, 3 BLADES AND CONTROL ®66 30W DC
MOTOR
220V/30W, 50Hz
EUROLAMP®
Pioneers in New Technology
Please read these instructions carefully. Please pay particular attention
to the safety information. We recommend that you keep the instructions for
future reference.
SAFETY RECOMMENDATIONS
It is essential to read and understand all the safety and operating
instructions be- fore the installation. If this is your first time using the
device, keep the instructions secure for future reference.
In cases where the connection to a direct power supply needs to be made, it is
necessary to be done by a qualified person.
It can be cleaned with a dry and clean fabric or with a use of neutral
detergent. Do not use solvents or corrosive products. In case that the surface
is wet, wait until it gets dry and then use it. Avoid contact on all
electrical parts with liquids The device should be kept out of the reach of
children and minors.
The warranty is no longer valid when there are defects in the product where
come from damages or when the parts of the product has been damaged by
unauthorized persons as well as after any intervention on the device due
improper handling or misuse.
Follow the instructions below for safe use and installation. As you unpacking
the product, check for damages. In that case, please inform your supplier.
ATTENTION: Electrical connections must be made by a qualified
electrician and in accordance with European rules for electrical
installations.
IMPORTANT: THE COMPANY IS NOT RESPONSIBLE FOR THE INSTALLATION. INSTALLA-
TION IS THE SOLE RESPONSIBILITY OF THE CUSTOMER.
CAUTION: Before installing the fan, be sure to turn off the power supply.
Do not turn on power until the fan is fully installed and ready for use.
EUROLAMP SA reserves the right to interpret and amendment the content of this
document at any time without prior notice.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.
PARTS INVENTORY
INSTALLATION PREPARATION
To prevent personal injury and damage, ensure that the blades are at least
2.3m from the floor and also leave a 76cm space from any wall or object that
may obstruct.
Be sure the outlet box is securely attached to the installation surface and
can fully support the weight of the fan.
PREPARING THE FAN SITE
Down-rod Installation
This fan can be mounted with a down-rod onto either a normal or vaulted
ceiling. The hanging
length can be extended by a longer down-rod. For installation, we’ll require
these tools: a screw-driver, a flat-head screwdriver, an ad- jus table pliers
or wrench, a stepladder, wire cutters, and rated electrical tape.
Standard Mounting StyleStandard Mounting hangers from the ceiling using a down-rod
REMOTE CONTROL RECEIVER CONNECTION
CANOPY ASSEMBLY
Raise the canopy onto the hanging bracket, then align the loosened screws on
the hanging bracket with the holes in canopy. Twist the canopy to lock it. Re-
insert and tighten the screws using a screwdriver.
With the hanging bracket secured to the outlet box, you are now ready to hang
your fan. Take the fan firmly with two hands. Slide the down-rod through the
opening in the hanging bracket and let hanging the ball rest on the hanging
bracket. Turn the hanging ball slot until it lines up with the hanging
bracket tab.
Note: Seek the help of another person to hold the stepladder in place and
to lift the fan up to you once you are up on the ladder.
INSTALLING THE HANGER BRACKET
Drill an 8mm hole into the concrete ceiling and insert the bolt.
Align the bracket with the hole, then tighten using a nut.
WELCOME
Thank you for choosing our Ceiling Fan with LED Light
In this manual, you will find the instructions, warnings and recommendations
necessary to enjoy
our product safely and satisfactorily. Before connecting your appliance, take
time to carefully
read the safety precautions
PARTS
Carefully open the packaging. Remove the items from their Styrofoam inserts.
Remove the mo-tor housing and place it somewhere safe (in the Styrofoam) to
avoid damaging the finish. Check the parts inventory to make sure that all
parts have been included.
INSTALLATION PREPARATION
To prevent personal injury and damage, ensure that the blades are at least
2.3m from the floor and also leave a 76cm space from any wall or object that
may obstruct.
Be sure the outlet box is securely attached to the installation surface and
can fully support the weight of the fan.
PREPARING THE FAN SITE
Down-rod Installation
This fan can be mounted with a down-rod onto either a normal or vaulted
ceiling. The hang- ing length can be extended by a longer down-rod. For
installation, we’ll require these tools: a screw-driver, a flat-head
screwdriver, an adjustable pliers or wrench, a stepladder, wire cutters, and
rated electrical tape
Standard Mounting Style
Standard Mounting hangers from the ceiling using a down-rod.
Angled Mounting Style
Angled Mounting recommended for a vaulted or angled ceiling.
INSTALLING THE HANGER BRACKET
Drill an 8mm hole into the concrete
ceiling and insert the bolt. Align the bracket with the hole, then tighten
using a nut.
Pioneers in New Technology!
IMPORTED IN EU BY
EUROLAMP SA:
KAMPOS DIAVATA – ION IA 570 08,THESSALONIKI – GREECE
T: +30 231 0 574802
info@eurolamp.gr
www.eurolampglobal.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>