EUROLAMP WS52-5C1L Decorative Fans with Light Instructions
- June 12, 2024
- EUROLAMP
Table of Contents
Pioneers in New Technology
INSTRUCTIONS
DECORATIVE FANS WITH LIGHT
70W E27
WS52-5C1L Decorative Fans with Light
147-29006
(WS52-5C1L)
NICKEL-BROWN
Φ132
| 147-29007
(WS52-4C1L)
SAND NICKEL
Φ132
| 147-29009
(WS52-5C1L)
NICKEL MAT
Φ122
---|---|---
300-25000
(WS52-4C1L)
BROWN GOLD
Φ132
| 300-25026
(WS52-R3C1L)
GREY
Φ132
| 300-25027
(WS52-R3C1L)
WHITE
Φ132
Please read these instructions carefully. Please pay particular attention to the safety information. We recommend that you keep the instructions for future reference.
SAFETY RECOMMENDATIONS
- It is essential to read and understand all the safety and operating instructions before the installation. If this is your first time using the device, keep the instructions secure for future reference.
- In cases where the connection to a direct power supply needs to be made, it is necessary to be done by a qualified person.
- It can be cleaned with a dry and clean fabric or with a use of neutral detergent. Do not use solvents or corrosive products. In case that the surface is wet, wait until it gets dry and then use it. Avoid contact on all electrical parts with liquids.
- The device should be kept out of the reach of children and minors.
- The warranty is no longer valid when there are defects in the product where come from damages or when the parts of the product has been damaged by unauthorized persons as well as after any intervention on the device due improper handling or misuse.
- Follow the instructions below for safe use and installation. As you unpacking the product, check for damages. In that case, please inform your supplier.
ATTENTION: Electrical connections must be made by a qualified electrician
and in accordance with European rules for electrical installations.
IMPORTANT: THE COMPANY IS NOT RESPONSIBLE FOR THE INSTALLATION.
INSTALLATION IS THE SOLE RESPONSIBILITY OF THE CUSTOMER.
CAUTION: Before installing the fan, be sure to turn off the power supply.
Do not turn on power until the fan is fully installed and ready for use.
EUROLAMP SA reserves the right to interpret and amendment the content of this
document at any time without prior notice.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.
SAFEGUARDS
Read all instructions carefully, even if you feel you are quite familiar with this type of appliance. When using electrical appliances, in order to reduce the risk of fire, electric shock, and/or injury, these basic safety precautions should always be followed:
- This appliance must be installed by a Qualified Electrical Contractor in accordance with the local regulations, and all local, state and national electrical codes. Any alterations or additions to building wiring must be completed by a licensed electrical mechanic, or person authorized by legislation to work on the fixed wiring of any electrical installation.
- The ceiling fan must be connected to a 230V~50/60HZ power supply.
- All electrical work must only be undertaken after disconnection of the power by removing fuses or turning off the circuit breaker, to ensure all pole isolation of the electrical supply.
- The fan must be earthed.
- The fan must be installed so that the blades are at least 2.3metres above the floor.
- The structure that the ceiling fan is connected to must be capable of supporting a weight of at least 45kg. The fixing must be able to support the moving weight of the fan and must not twist or work loose.
- Make sure that the installation site will not allow the rotating fan blades to come into contact with any object and that there is a minimum clearance of 150mm (6″) from the blade tip to the wall or ceiling. Please note that the bigger this clearance is the better the airflow from your fan will be.
- Do not use outdoors. Installing the fan in a position where it could be exposed to water or moisture is dangerous.
- Do not connect the fan motor to a dimmer switch. This may give an unsatisfactory performance (motor hum) and cause damage to the motor.
- This appliance is not intended for use by young children or infirm persons without supervision.
- Young children should be supervised to ensure that they do not play with the appliance.
- It is not recommended that ceiling fans and gas appliances be operated in the same room at the same time.
- The fan must be turned off and stopped completely before reversing the fan direction. This will prevent any damage to the motor of the fan or controller (if installed).
- Do not insert anything into the fan blades whilst they are spinning. This will damage the blades and upset the balance of the fan causing the unit to wobble.
- After the fan is completely installed make sure that all base and fan blade fixings are secured and tightened to prevent any problems.
- Because of the fan’s natural movement, some connections may loosen. Check the support connections, brackets and blade attachments twice a year to make sure they remain secured. If any are loose, tighten.
PREPARATION
Unpack your ceiling fan carefully, then remove all parts and components, and
lay on a cloth or soft surface to avoid damage. Do not lay the motor housing
on its side, the housing may get damaged. Before commencing installation,
check that all parts are included.
NB: You may need to remove all foam packaging material to ensure there
are no missing components.
- Make sure that the installation site will not allow the rotating fan blades to come into contact with any object and that there is a minimum clearance of 150mm (6″) from the blade tip to the wall or ceiling. Please note that the bigger this clearance is the better the airflow from your fan will be. DO NOT use outdoors. Installing the fan in a position where it could be exposed to water or moisture is dangerous. If the location you have chosen does not have a suitable support beam capable of supporting 45Kg, install a brace 2″ x 4″ between the ceiling joists as a support medium. Secure the hanging bracket to the ceiling joist or suitable structure that is capable of carrying a load of at least 45Kg, with the two long fixing screws provided. Ensure that at least 30mm of the screw is threaded into the support.
- Place the assembled fan into the bracket and make the wiring connection.
- Place the canopy over the bracket, align the canopy holes with the screws and tighten.
ELECTRICAL CONNECTIONS
This product has the connection type “Y”. If the cord is damaged, it must be replaced by the manufacturer or its service representative or qualified personnel to avoid the risk. You will not have to repair the appliance yourself. This should only be done by qualified personnel. Only genuine spare parts can be used for repair.
REMOTE CONTROL – FUNCTIONS TRANSMITTER
For ceiling fan by remote controller, you should the transmitter pointing to
I. R. sensor.
For turning on the receiver, press and hold the “STOP” button for 3 seconds.
Light will (if installed) blinks 2 times. They will be synchronized when hear
a prolonged signal.
STOP: Turn off ceiling fan.
HI: Turn on ceiling fan at high speed.
MED: Turn on ceiling fan at medium speed.
LOW: Turn on ceiling fan at low speed.
LIGHT: ON/OFF-Press and release immediately to turn on or off the light.
INSTALLATION INSTRUCTIONS
CAUTION: Incorrect cable connection will damage the receiver.
- The RF wireless technology of the digital transmission is prepared for doing an individual control, because it is provided with a coincident code index of less than 1/50000. The same code number is set in the back part of the emitter and the receiver. It is necessary this code number for repair service in the case of damage.
- In wide spaces the receiver can be used in any angle no matter the direction. If the fan and the lamp are provided of a switch, please set the fan at maximum speed and turn on the lamp before start using the remote control
Pioneers in New Technology
IMPORTED IN ΕU BY
EUROLAMP SA:
KAMPOS DIAVATA – IONIA
570 08,THESSALONIKI – GREECE
T: +30 2310 574802
MADE IN CHINA
info@eurolamp.gr
www.eurolampglobal.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>