KEONJINN B086VDPVRV Bathroom LED Mirror Instruction Manual

June 2, 2024
KEONJINN

KEONJINN B086VDPVRV Bathroom LED Mirror Instruction Manual

HOW TO USE AND CLEAN

In order to keep the LED mirror in perfect condition, we suggest a proper use and regular cleaning.

  1. Please ensure that the product is used within the safe voltage range of 100V-120V.
  2. Please wrap electrical tape around the wires to prevent electrical leakage.
  3. Avoid using hard or pointed items to strike the mirror glass so as to prevent damage.

How to Clean

When cleaning the mirror, please follow these steps:

  1. Use a soft, non-abrasive cloth to clean the mirror. Avoid using rough or abrasive materials that may damage the surface.
  2. Do not use any cleaning agents that may cause irritation or damage to the mirror’s finish. Instead, use any of the recommended cleansers to remove dirt and grime:

Gentle liquid detergents
Colorless cleansers

Warranty

A two-year warranty from the date of your purchase.

If you have any questions, please feel free to contact us via
sales@keonjinn.com

BEFORE INSTALLATION

Thank you for choosing Keonjinn products. To ensure the best possible experience, please read carefully and follow the instructions provided below before assembling and installing the product.

Important Safety Instructions:

  • Assembly by two or more adults is highly recommended, in order to ensure proper installation.
  • To connect the wires to the electrical junction box, consultation with a qualified technician or electrician is highly recommended.
  • Disconnect power before installing, adding, or changing any components.
  • Make sure that the fixing location can support the weight of the entire fixture (e.g. solid stone or brick walls).
  • To prevent injury, the mirror must be installed according to the instructions provided.

Pre-assembly:

  • Inspect the product immediately upon receipt for any transit damage or missing parts.
  • The voltage for your product should be between 100V and 120V. If the voltage exceeds 120V, please use a transformer.
  • You can connect the wires directly to your junction box or plug.
  • Do not remove the transparent silicone protector until the installation is complete.

Before Installation:
please check to make sure the mirror is working properly:

  1. Anti-fog
    The anti-fog function helps resist the troubling fog and keep a clear reflection image. To save energy, it will automatically turn off after one hour.

  2. Color Temperature
    You can select the color temperature by tapping the button: the first tap is white light, the second tap is warm light, and the third one is natural light.

  3. ON/OFF, Lighting Mode, and Brightness
    The lighting mode will change as you tap the button: the first tap is for front light and backlight, the second tap is for front light only, the third one is for backlight only, and the light will be all off with a fourth tap. The brightness can be adjusted with a long press on the button. If no button is pressed within 15 seconds, the next tap will turn off the light immediately. Memory Function: The current setting of the mirror will be saved. When you turn on the mirror next time, it will be in the same settings as it was.

CONTACT US

After opening the package, please inspect the product immediately and see if there is any damage or missing parts. If there is,  please contact us by sales@keonjinn.com or find us at Amazon by following steps:

  • Open “Orders” at Amazon, find the product you have purchased and open the product page;
  • Click Sold by “Keonjinn”, and click “Ask a question” on the redirected page;
  • Click “An order I have placed” in the chat with Seller Messaging Assistant;
  • Click in sequence “Your product”, “Other”, “Troubleshooting” from available options, you will see a message box after that.

Please leave us a message, and we will reply within 24 hours.

PACKING LIST

  • Wall Anchors

  • Wall Anchors

  • Screws

  • Bracket

  • LED Mirror

INSTALLATION TOOLS

| | |
---|---|---|---
Level| Pencil| Hammer| Safety Goggles
| | |
Electric Drill| Phillips Screwdriver| Tape Measure|

INSTALLATION INSTRUCTIONS

  1. Decide where to install the mirror. Make sure the bracket is located horizontally with the help of a level ruler, and mark the spots ① ② ③ for drilling on the wall.
    Note: Please hang the mirror a few inches above the highest part of the faucet.

  2. Drill holes where marked and insert anchors.

  3. Mount the bracket to the wall with screws.

  4. Connect the power by plugging into an outlet or hardwired to a standard circuit panel.

    • Plug-in
      After hanging the mirror securely, plug the power cable to a standard socket

    • Hardwired
      Cut the head off the plug and hardwire it into an outlet.
      Black wire — power supply L (LIVE)
      White wire — power supply N (NEUTRAL)
      Green wire — power supply E (EARTH)


      WARNING: This mirror must be earthed.
      REMINDER : Please make sure the power is cut off before installation.

  5.  Place the mirror against the wall, align the hook with the mounted bracket, slowly lower the mirror down, and make sure that it slots into the right position and hangs securely.

SPECIFICATIONS

Dimension Watts Lumens
φ24 36W 3000LM
φ28 36W 3500LM
φ30 48W 4000LM
φ36 60W 4900LM
φ40 60W 5500LM
Parameter Specifications
Color Temperature 3000-6000K
Input Voltage AC100-120V
Output Voltage 24V DC
CRI ≥90 Ra
Working Temperature -20~50℃
Life Span ≥20000 hours
Anti-fog Yes
Safety Compliance ETL
IP Rate IP44
Mirror Glass 5 mm
Wiring Method Hardwired / Plug in
Switch Touch Sensor Switch
Mounting Method Wall Mount

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals