KEONJINN B08MVW1NXP LED Lighted Mirror Installation Guide
- June 16, 2024
- KEONJINN
Table of Contents
KEONJINN B08MVW1NXP LED Lighted Mirror
HOW TO USE AND CLEAN
In order to keep the LED mirror in perfect condition, we suggest a proper use and regular cleaning.
How to Use
- Please ensure that the product is used within the safe voltage range of 100V-120V.
- Please wrap electrical tape around the wires to prevent electrical leakage.
- Avoid using hard or pointed items to strike the mirror glass so as to prevent damage.
How to Clean
When cleaning the mirror, please follow these steps:
- Use a soft, non-abrasive cloth to clean the mirror. Avoid using rough or abrasive materials that may damage the surface.
- Do not use any cleaning agents that may cause irritation or damage to the mirror’s finish. Instead, use any of the recommended cleansers to remove dirt and grime:
Gentle liquid detergents
Colorless cleansers
Warranty
A one-year warranty from the date of your purchase.
BEFORE INSTALLATION
Thank you for choosing Keonjinn products. To ensure the best possible experience, please read carefully and follow the instructions provided below before assembling and installing the product.
Important Safety Instructions:
- Assemble the product by two or more adults to ensure proper installation.
- To connect the wires to the electrical junction box, consultation with a qualified technician or electrician is highly recommended.
- Disconnect power before installing, adding, or changing any components.
- Make sure that the fixing location can support the weight of the entire fixture (e.g. solid stone or brick walls).
- To prevent injury, the mirror must be installed according to the instructions provided.
Pre-assembly:
-
Inspect the product immediately upon receipt for any transit damage or missing parts.
-
The voltage for your Keonjinn product should be between 1 00V and 120V.
If the voltage exceeds 120V, please use a transformer. -
You can connect the wires directly to your junction box or plug.
-
Do not remove the transparent silicone protector until the installation is complete.
Before Installation:
Please check and make sure that the mirror is functioning properly.
-
Power Check
After connecting the power, the two buttons will turn white, indicating that the LED and anti-fog functions are turned on. If you don’t need to use any of them, touch the corresponding button to turn it off, and the button will dim. -
Anti-fog
The anti-fog function helps resist the troubling fog and keep a clear reflection image. To save energy, it will automatically turn off after one hour. -
Touch Switch
Mirror with tri-color temperatures
The button controls the light brightness and color temperature. Keep holding it and the brightness will change. You can adjust the color temperature as well: the first tap is white light, the second one is warm light, and the third one is natural light.
If no button is pressed within 15 seconds, the next tap will turn off the light immediately.
Mirror with single color temperature
The button controls the light brightness. Keep holding it and the brightness will change. -
Memory Function
The current setting of the mirror will be saved. When you turn on the mirror next time, it will be in the same settings as it was.
CONTACT US
After opening the package, please inspect the product immediately ~ and see if there is any damage or missing parts. If there is, please IO l contact us by sales@keonjinn.com or find us at Amazon by ~ following steps:
- Open “Orders” at Amazon, find the product you have purchased and open the product page;
- Click Sold by “Keonjinn”, and click “Ask a question” on the redirected page;
- Click “An order I have placed” in the chat with Seller Messaging Assistant ;
- Click in sequence “Your product”, “Other”, “Troubleshooting” from available options, you will see a message box after that.
Please leave us a message, and we will reply within 24 hours.
ACCESSORIES LIST
TOOLS REQUIRED
INSTALLATION INSTURCTIONS
-
Decide whether to hang the mirror vertically or horizontally. Confirm the locations of drill holes with the positioning ruler provided in the package, and use a marker to mark the spots 1 2 3 4 on the wall.
-
Use an electric drill to punch holes at the marked spots, and then apply wall anchors with a hammer.
Thickness of Wall
|
Recommended Drill Bit
---|---
16mm| 1/4″ (6mm) drill bit, drilling depth in 1 31/32″ (50mm)|
8-16mm| 25/64″ (10mm) drill bit|
<8mm| Inapplicable
3. Secure the two brackets to the wall with screws.
-
Connect the power by plugging into an outlet or hardwired to a standard circuit panel.
-
Plug-in
After hanging the mirror securely, plug the power cable to a standard socket.
-
Hardwired
Cut the head off the plug and hardwire it into an outlet.
Black wire — power supply L (LIVE)
White wire — power supply N (NEUTRAL}
Green wire — power supply E (EARTH)
WARNING: This mirror must be earthed.
REMINDER: Please make sure the power is cut off before installation.
-
-
Place the mirror against the wall, align the hook with the mounted bracket, slowly lower the mirror down, and make sure that it slots into the right position and hangs securely.
SPECIFICATIONS
PARAMETER | SPECIFICATION |
---|---|
Color Temperature {Triple color lights) | 3000-6000K |
Color Temperature (Single color light} | 6000K |
Input Voltage | AC100-120V |
Output Voltage | 24V DC |
CRI | 90 Ra |
Working Temperature | -20~50°C |
Life Span | 20000 hours |
Anti-fog | Yes |
Safety Compliance | ETL |
IP Rate | IP44 |
Mirror Glass | 5mm |
Wiring Method | Hardwired / Plug in |
Switch | Touch Sensor Switch |
Installation Method | Wall-mounted |
Customer Support
If you have any questions, please feel free to contact us via sales@keonjinn.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>