Comsol 10W Wireless Fast Charging Stand User Manual
- June 7, 2024
- comsol
Table of Contents
Comsol 10W Wireless Fast Charging Stand
Compatibility
Compatible with Qi-enabled devices* including
- iPhone X
- Samsung SB/SB+
- Sony Xperia XZ2
- iPhone 8
- Samsung S7/S7 Edge
- Nokia 8 Sirocco
- iPhone 8 Plus
- Samsung Note 8
- LG G7 ThinQ
- Samsung S9/S9+
- Samsung Note s
- LG V30+
Features
- Two charging coils enable large wireless coverage to allow charging in portrait or landscape mode
- Supports 1 OW wireless fast charging for compatible devices such as Samsung Galaxy S9, S9+, SB, SB+, Note 8, S7 & S7 Edge
- Supports 7.SW Apple wireless fast charging for iPhone X/8/8 Plus
- Supports SW standard wireless charging for all Qi enabled devices
- No need to remove your protective case. Works with most cases up to 3mm thick
- LED indicator to show charging status
- Smart IC enables energy saving mode when device is fully charged
- Full safety protection for your devices with Qi certified temperature control, strict voltage regulation & short circuit protection
- Includes 1.Sm micro USB cable to connect charging stand to USB wall charger (USB wall charger not included)
- Check with device manufacturer for Qi wireless compatibility
- When connected to a Quick Charge 2.0 or 3.0 wall charger (not included)
Wireless Charger Operation
- Using the included micro USB cable, connect the wireless charging stand to a USB wall charger (USB wall charger not included)
- It is recommended to use original or reputable 3rd party branded USB wall chargers. For faster charging limes it is recommended to use a USB wall charger with a minimum of 2A output
- When connected to the USB charger, the red LED will be on for 3 seconds to indicate the charging stand is powered on and in stand-by mode
- Place your Qi enabled wireless phone on the charging stand and your phone should start charging automatically
- The LED will flash green to indicate charging
- If your phone does not start charging, move your phone until the correct position is found and your phone starts charging
- When your phone is fully charged, the Smart IC enables energy saving trickle charge mode
Please Note
To achieve 1 OW fast charging for Android devices or 7.5W fast charging for Apple devices, the charging stand needs to be connected to a Quick Charge 2.0 or 3.0 wall charger (not included)
Specifications
- Wireless Standard: WPC/Qi (v1 .2.3)
- Quantity of Wireless Charging Coils: Two Coils
- Input: DC SV 2A or DC 9V 2A
- Output: SW I 7 .SW I 10W (Max)
- Working Frequency: 11 Oto 20SKH
- Charging Distance: 3 to 8mm
- Charging Efficiency: > 72%
- Dimensions: 125 x 70 x 98mm
- Weight: 178g
Important Safety Instructions
- Only use original or reputable third party chargers and cables
- Do not get wet to avoid causing short circuit damage and leakage
- Do not use in extreme hot, humid or corrosive environments to avoid short circuit damage and leakage
- Do not place too close to magnetic strip or chip ID card to avoid magnetic failure
- Do not place within 20cm of implantable medical devices (pacemaker, cochlear implant etc.) to avoid potential interference
- Do not clean with harmful chemicals or detergents
- Misuse, dropping or excessive force may cause damage to the charging stand
Please Note: When wirelessly charging a device, the wireless charger and your device may feel warm. This is a normal operating condition and should not be cause for concern.
iPhone is a trademark of Apple inc., registered in the U.S. and other
countries.
The ‘Qi’ Symbol is a trademark of the Wireless Power Consortium. Android is a
trademark of Google Inc.
Qi Certified
Certification program ensures this charger has passed rigorous tests to
guarantee safety, compatibility and energy efficiency.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>