KEONJINN K1MIGB004 LED Mirror For Bathroom Installation Guide

KEONJINN K1MIGB004 LED Mirror For Bathroom Installation Guide

PRODUCT SPECIFICATION

CONTACT US

Note: After opening the package, Please inspect the product immediately for damage in transit or missing parts. If there is any missing, Please contact us by (sales@keonjinn.com) or you can contact us at Amazon by following these steps:

• Open “Orders” at Amazon
• Find the product you have purchased and open the product page
• Click Sold by “keonjinn” -Click”Ask a question”
• Click “An order | have placed”
• Click “Your product” -Click “Other” -Click “Troubleshooting”

Then you can send us messages, we will reply within 24 hours. Manufacturer warranty for 2 year from date of purchase.

Packing list

• Mirror x 1

• Bracket x 1

• Screws x(4+2)

• Anchors x(4+2)

The wall bracket is placed on the back of the mirror.

USE INSTRUCTION

1. Please use in safe voltage range. (100V-120V)
2. Use electrical tape to wrap around the wires to prevent leakage.
3. Do not strike mirror glass with hard or pointed items.

DANGER : Before installation, make sure the main power is cut off.
WARNING : Installation must be performed by qualified licensed electrician.

BEFORE INSTALLATION

Note: Thank you very much for using Keon jinn products, in order to facilitate the use of keno jinn products, please read this instruction carefully before you begin installation.

Important Safety Instructions:

• Please read all instructions carefully before assembling the item.
• Assembly by two or more adults is highly recommended.
• To connect the wires to electrical junction box, a qualified technician or electrician is highly recommended.
• Disconnect power before installing, adding or changing any components.
• Ensure that the fixing location is able to take the weight of the complete fitting. (solid stone / brick walls).
• To prevent injury, the mirror must be installed according to these instructions.

Pre-assembly:

• After opening the package, inspect the product immediately upon receipt for transit damage or missing parts.
• Keep the voltages between 100V and 120V. If the voltage exceeds 120V, please use transformer.
• You can connect the wires directly to your junction box or the plug.

Before installation, please check to make sure the mirror is working properly :

1. The left button is the anti-fog switch. Anti-fog film will automatically turn off one hour of opening. When you are not using it, remember to turn off the switch to prevent wasting energy.

2. The right button is a smart light switch. This switch can control the light brightness and color temperature switching. You could adjust the color of light according to your preference: the first touch is natural light, the second touch is white light, and the third touch is yellow light, then off, and so on. Keep holding it and the brightness will change.

INSTALLATION

Installation Tools

• Electric Drill

• Hammer

• Marker Pen

• Tape Measure

• Level

• Phillips Screwdriver

• Safety Goggles

1. Before installation, please lift the mirror against the wall, keep an appropriate safety distance from the faucet, confirm the installation position and installation height of the bracket, use a spirit level to level the bracket, and mark the hole position on the wall.
   The mirror can be hung horizontally or vertically. You can choose the hanging method according to your preference. Here is the vertical hanging installation method, the horizontal hanging is the same.

2. Use an electric drill to punch holes at the marked spots, and then apply wall anchors with hammer. (5/16″ (8mm) drill bit, drilling depth in 13/4” (45mm) )}

Note: Please wear goggles and pay attention to safety.

3. Mount the bracket to the wall with screws.

4. Connect the power. You can use the plug directly or connect the wire to a standard switch lighting circuit.
   Installation hardwired
   BLACK WIRE — POWER SUPPLY L (LIVE)
   WHITE WIRE — POWER SUPPLY N (NEUTRAL)
   GREEN WIRE — POWER SUPPLY E (EARTH)
   WARNING: This mirror must be earthed.

DANGER: Before installation, make sure the main power is cut off.

5. Place the mirror against the wall, align the hook with the bracket slot, slowly lower it so that the hook fits into the slot, and gently shake the mirror to ensure that the mirror is securely installed.

Note: Two-person installation.

Installation plug

If you want to connect power wires to plug, you can refer to the steps:

1. Remove the plug cover.

2. Unscrew the screws on each of the plug’s pins.

3. Insert the twisted copper wires into the holes in the pins.

4. Tighten the small screw on each plug pin to ensure that the wire is tightly clamped by the clip.

5. Install the wire brake to prevent the wire from pulling out.

6.  Put-on the cover of the plug.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>