KEONJINN JG04 Chrome Bathroom Medicine Cabinets with Mirror Instruction Manual

KEONJINN JG04 Chrome Bathroom Medicine Cabinets with Mirror

Product Information

Specifications:

• Size: 16 x 24, 20 x 26, 20 x 32, 24 x 32, 30 x 32, 40 x 32, 48 x 32, 60 x 32
• Dimension:
  • 40 x 61 x 13 cm
  • 51 x 66 x 13 cm
  • 51 x 81 x 13 cm
  • 61 x 81 x 13 cm
  • 76 x 81 x 13 cm
  • 101 x 81 x 13 cm
  • 121 x 81 x 13 cm
  • 152 x 81 x 13 cm
• Types of Medicine Cabinet: Single-door, Double-door, Triple-door

Product Usage Instructions

Cleaning the Cabinet:

When cleaning the cabinet, please follow these steps:

1. Use a soft, non-abrasive cloth to clean the mirror. Avoid using rough or abrasive materials that may damage the surface.
2. Do not use any cleaning agents that may cause irritation or damage to the mirror’s finish. Instead, use any of the recommended cleansers to remove dirt and grime.
3. If any adhesive residue is left, please wipe it off with a cloth dipped in water (instead of detergents).

Warranty:

A two-year warranty is provided from the date of your purchase.

Product Inspection and Contact Information:

After opening the package, please inspect the product immediately for any damage or missing parts. If there is any issue, please contact us at sales@keonjinn.com or find us on Amazon by following these steps:

1. Open Orders at Amazon and find the product you have purchased.
2. Open the product page and click on “Sold by Keonjinn”.
3. On the redirected page, click “Ask a question”.
4. In the chat with Seller Messaging Assistant, select “An order I have placed” and choose “Your product, Other, Troubleshooting” from the available options.
5. You will see a message box after that. Please leave us a message, and we will reply within 24 hours.

Required Tools:

• Wall Anchor-A
• Wall Anchor-B
• Rubber Gasket
• Washer
• Screw Cap
• Short Screw
• Long Screw
• Spout Plug
• Bubble Level (Cabinet height 32)
• Level Ruler
• Marker
• Hammer
• Tape Measure
• Phillips Screwdriver 1
• Safety Goggles

Installation Instructions:

Before Installation:

Thank you for choosing Keonjinn products. To ensure the best experience, please read carefully and follow the instructions provided below before assembling and installing the product.

Inspect the product immediately upon receipt for any transit damage or missing parts.

Wall Preparation:

Thickness Of Wall: 5/8 (16mm)

Recommended Drill Bit: 1/4 (6mm) drill bit, drilling depth in 131/32 (50mm)

NOTE: Please wear goggles and pay attention to your safety while drilling.

1. Confirm the location for installation and draw a line on the wall with a level and marker to indicate where the cabinet bottom is.
2. NOTE: Please hang the cabinet at least 3 inches below the light and above the faucet.

Cabinet Installation:

• Thickness Of Wall: 5/8 (16mm)
• Recommended Drill Bit: 1/4 (6mm) drill bit, drilling depth in 131/32 (50mm)

NOTE: Please hold the door when detaching it from the cabinet, in case it drops to the floor and gets damaged.

1. Before your installation, remove the cabinet door first by detaching the hydraulic hinges. Press here to detach.
2. NOTE: Please hang the cabinet at least 3 inches above the faucet.

FAQ

Q: What are the available sizes of the medicine cabinet?
A: The available sizes are 16 x 24, 20 x 26, 20 x 32, 24 x 32, 30 x 32, 40 x 32, 48 x 32, and 60 x 32.

Q: What is the warranty period for the product?
A: The product comes with a two-year warranty from the date of purchase.

Q: How do I contact customer support?
A: You can contact us at sales@keonjinn.com or find us on Amazon by following the instructions provided in the user manual.

Contact Us

After opening the package, please inspect the product immediately and see if there is any damage or missing parts. If there is, please feel free to contact us by sales@keonjinn.com or find us at Amazon by following steps:

• Open “Orders” at Amazon, find the product you have purchased and open the product page;
• Click Sold by “Keonjinn“, and click “Ask a question” on the redirected page;
• Click “An order I have placed“ in the chat with Seller Messaging Assistant ;
• Click in sequence “Your product“, ”Other”, “Troubleshooting“ from available options, you will see a message box after that.

Please leave us a message, and we will reply within 24 hours.

Packing List

Tools Required

Before Inatallation

Thank you for choosing Keonjinn products. To ensure the best experience, please read carefully and follow the instructions provided below before assembling and installing the product.

1. Important Safety Instructions:
   • Assembly by two or more adults is highly recommended, in order to ensure proper installation.
   • Make sure that the fixing location can support the weight of the entire fixture (e.g. solid stone or brick walls).
   • To prevent injury, the product must be installed according to the instructions provided.
   • The medicine cabinet can be wall-mounted or recess-mounted. If you prefer wall mounting, the wall should be covered with wood panels and supported by a framed wall studs behind, or a strong concrete wall.
2. Pre-assembly:
   • Inspect the product immediately upon receipt for any transit damage or missing parts.
3. Before Installation:
   • Please confirm whether your medicine cabinet would be mounted with the door open to the left or right. If you want it open to the right, then detach (0) and flip the shelves (3), and turn the cabinet upside down (3) before installation. (Shelves are adjustable in cabinets of 32″ or higher.)

Single-Door Cabinet: Wall-Mounted

1. Confirm the locations for drilling holes with the positioning ruler and a level ruler, and use a marker to mark the spots 0330 on the wall.
   NOTE: Please hang the cabinet at least 3 inches above the faucet.

2. Use an electric drill to punch holes at the marked spots (①), then apply the 4 wall anchors with a hammer (②).
   NOTE: Please wear goggles and pay attention to your safety while drilling.

3. One person lifts up the medicine cabinet and aligns it to the screw holes (①), while another person secure the medicine cabinet to the wall with the 4 screws (②).

Single-Door Cabinet: Recessed

1. Confirm the location for installation, and draw a line on the wall with a level and marker to indicate where the cabinet bottom is.
   NOTE: Please hang the cabinet at least 3 inches below the light and above the faucet.

2. Based on the drawn line in step 1, measure the length, width and depth of the cabinet back, and mark them on the wall (1). Cut the drywall as per the marks and remove the cutout (2).

3. Mark spots for wall anchors (P), and use an electric drill to punch holes at the spots (2), then apply the 4 wall anchors with a hammer (3).

4. Put the cabinet in the drywall together (0) and secure the cabinet with screws (2).

Double/Triple-Door Cabinet: Wall-Mounted

1. Before your installation, remove the cabinet door first by detaching the hydraulic hinges.
   NOTE: Please hold the door when detaching it from the cabinet, in case it drops to the floor and gets damaged.

2. Confirm the locations for drilling holes with the positioning ruler and a level ruler, and use a marker to mark the spots ①②③④ on the wall.
   NOTE: Please hang the cabinet at least 3 inches above the faucet.

3. Use an electric drill to punch holes at the marked spots (①), then apply the 4 wall anchors (6 anchors for a triple-door cabinet) with a hammer (②).
   NOTE: Please wear goggles and pay attention to your safety while drilling.

4. One person lifts up the medicine cabinet and aligns it to the screw holes (①), while another person secure the medicine cabinet to the wall with the 4 screws (②) (6 screws for a triple-door cabinet).

5. Reinstall the cabinet door by attaching hydraulic hinges.

How to Adjust Hydraulic Hinges

• Turn screw 1 to release the mounting plate from the cabinet, allowing the door to be moved up and down;
• Turn front screw 2 to adjust the depth of door overlay;
• Turn the eccentric screw 3 to adjust the gap between the door and cabinet.

NOTE: No hydraulic hinges are applied in single-door medicine cabinets, which adopt piano hinges instead.

Double/Triple-Door Cabinet: Recessed

1. Before your installation, remove the cabinet door first by detaching the hydraulic hinges
   NOTE: Please hold the door when detaching it from the cabinet, in case it drops to the floor and gets damaged.

2. Confirm the location for installation, and draw a line on the wall with a level and marker to indicate where the cabinet bottom is.
   NOTE: Please hang the cabinet at least 3 inches below the light and above the faucet.

3. Based on the drawn line in step 2, measure the length, width and depth of the cabinet back, and mark them on the wall (①). Cut the drywall as per the marks and remove the cutout (②).

4. Mark spots for wall anchors (①), and use an electric drill to punch holes at the spots (②), then apply the 4 wall anchors with a hammer (③).

5. Put the cabinet in the drywall together (①) and secure the cabinet with screws (②).

6. Reinstall the cabinet door by attaching hydraulic hinges.

SPECIFICATION

HOW TO USE AND CLEAN

When cleaning the cabinet, please follow these steps:

1. Use a soft, non-abrasive cloth to clean the mirror. Avoid using rough or abrasive materials that may damage the surface.
2. Do not use any cleaning agents that may cause irritation or damage to the mirror’s finish. Instead, use any of the recommended cleansers to remove dirt and grime:
3. If any adhesive residue left, please wipe it off with a cloth dipped in water. (instead of detergents)

Warranty
A two-year warranty from the date of your purchase.

If you have any questions, please feel free to contact us on
sales@keonjinn.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>