Westinghouse 61192 Lighting Marla One Light Instruction Manual
- June 4, 2024
- Westinghouse
Table of Contents
61192 Lighting Marla One Light
Instruction Manual
61192 Lighting Marla One Light
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do
not proceed.
Contact a qualified electrician. Read all instructions before beginning.
Proper wiring is essential for the safe operation of this fixture. When
cutting or drilling into walls or ceilings, do not damage electrical wiring,
gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install the fixture. Return to the place of purchase.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed
to give you many years of beauty and service. For questions and comments,
please visit www.westinghouselighting.eu/contact-
us and
www.westinghouselighting.de/contact-us
NOTE: Carefully unpack fixtures and parts. Make sure all parts are
included before discarding any packing materials (see figure 1).
MOUNTING AND WIRING INSTRUCTIONS
NOTE: The line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.
-
Turn off the power at the circuit box to avoid possible electric shock.
-
Place mounting bar (B) flush against the wall at the desired mounting location. Using outside mounting bar holes as a guide, mark where pilot holes are to be drilled.
NOTE: Mounting bar must be straight for the fixture to hang straight. -
Inset two plastic anchors (G) into the pilot holes (for drywall).
-
Align outside mounting bar holes with plastic anchors (G) (If applicable). Secure mounting bar (B) into place using wood screws (E).
-
Make an electrical connection by loosening the terminal screws on the terminal block (M) and inserting the live, neutral, and ground terminals.
-
Tighten terminal screws. Make sure there are no stray wires.
-
Place the back plate (C) over the mounting bar (B) and secure it into place with mounting screws (A).
-
Install lamp (not supplied). (Please do not exceed the maximum capacity recommended on the socket).
-
Attach the shade (D) to the holder (F), and rotate the shade (D) clockwise until secure.
-
Turn the power back on at the circuit box.
CLEANING AND CARE
To clean, wipe the fixture with a soft cloth. Clean glass with mild soap.
Spraying from chemical cleaners can discolor the finish of the fixture. Do not
use scouring pads, powders, steel wool, or abrasive paper to clean this
fixture.
Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging
your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated
to take back your old appliance for disposal at least free of charge.
Appliance specifications – TECHNICAL CHARACTERISTICS
| Rated voltage | 220-240V~ |
|---|---|
| Rated frequency | 50/60 Hz |
| Rated wattage | E27 1 x Max. 60W |
| Protection class | CLASS I |
| IP number | IP20 |
Distributed by:
Westinghouse Lighting, Krefelder Strasse 562
D-41066 Germany
and Westinghouse is a trademark of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting
All Rights Reserved.
Made in China
www.westinghouselighting.eu
www.westinghouselighting.de
GS-26-JH07-WH21
References
- Contact Us
- Ceiling Fans | Lighting Fixtures | Lamps
- Ceiling Fans | Lighting Fixtures | Lamps
- Contact Us
- Ceiling Fans | Lighting Fixtures | Lamps
- Ceiling Fans | Lighting Fixtures | Lamps
- Contact Us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>