Ford M-16600-FG Raptor Carbon Fiber Tailgate Applique Instruction Manual
- May 15, 2024
- Ford
Table of Contents
Ford M-16600-FG Raptor Carbon Fiber Tailgate Applique
Specifications
- Part Number: M-16600-FG/FM
- Part Description: F150 RAPTOR CARBON FIBER TAILGATE APPLIQUE
Product Information
- The F150 RAPTOR CARBON FIBER TAILGATE APPLIQUE is a genuine Ford Performance part designed to enhance the appearance of your vehicle’s tailgate.
- It includes a tailgate applique, a hardware kit, and two emblems for installation.
Tools Needed for Installation
- Long Reach Pliers
- Panel Removal Tool Set
- Torx 30 Wrench/socket
Product Usage Instructions
Removal
- Remove the screws from the tailgate liner with a torque of 28 lb. in (3.2 Nm).
- Remove the tailgate liner.
- Remove the screws from the inner panel with a torque of 28 lb. in (3.2 Nm).
- Remove the inner panel.
- For vehicles with a Flexible Step:
- Remove the screws from the panel with a torque of 71 lb. in (8 Nm).
- Remove the tailgate liner.
- Remove the nuts with a torque of 71 lb. in (8 Nm).
- Disengage push pin retainers from the tailgate using a non-marring trim tool and remove the applique.
FAQ:
Q: Where can I find the most current instruction information?
- A: Please visit www.performanceparts.ford.com for the most up-to-date instructions.
Q: What should I do if I don’t understand the installation instructions?
- A: If you have any questions or need clarification, please call the Ford Performance Techline at 1-800-367-3788 for assistance.
Part Description
- NO PART OF THIS DOCUMENT MAY BE REPRODUC E D WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD P ERFORMANCE PARTS.
- Please visit www.performanceparts.ford.com for the most current instruction information
- PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION.
- AT ANY TIME, IF YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD PERFORMANCE TECHLINE AT 1-800-367-3788!
Kit Contents
Quantity | Part Name |
---|---|
1 | Tailgate Applique |
1 | Hardware Kit |
2 | Emblems |
Tools Needed
1 | Long Reach Pliers |
---|---|
1 | Panel Removal Tool Set |
1 | Torx 30 Wrench / socket |
Removal
NOTE: Removal steps in this procedure may contain installation details. Vehicles without Flexible Step
- Remove the screws from the tailgate liner. Torque: 28 lb.in (3.2 Nm)
- Remove the tailgate liner.
- Remove the screws from the inner panel.
- Torque: 28 lb.in (3.2 Nm)
- Remove the inner panel.
- Vehicles with Flexible Step
- Remove the screws from panel.
- Torque: 71 lb.in (8 Nm)
- Remove the tailgate liner.
- Remove the nuts.
- Torque: 71 lb.in (8 Nm)
- NOTE: Platinum tailgate applique shown, all others similar.
- NOTE: Use care when disengaging push pins from tailgate to avoid damage to the applique.
- Using a non-marring trim tool, disengage the push pin retainers from the tailgate and remove the applique.
- Install the (29) plastic clips to back of applique
- Install the (2) threaded stud fasteners and (4) foam washers (to be reused from original part)
Install the Applique Panel
- To install, reverse the removal procedure.
- Fasten the (2) emblems to applique, clean surface with rubbing alcohol prior to adhering emblems.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>