Ford CV-21FTR Ex Guard Coverages Archive Installation Guide

June 1, 2024
Ford

Ford-LOGO

Ford CV-21FTR Ex Guard Coverages Archive

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-1

Product Specifications

  • Model: XYZ Guard and Bracket Kit
  • Material: Steel
  • Color: Black
  • Weight : 5 lbs
  • Dimensions: 24″ x 12″ x 6″

Product Usage Instructions

Tools Needed for Installation:
Tools included with the guard and bracket kit.

Installation Steps

Step 1:
Using a flat screwdriver, release 2 clips on both sides (1 per side).

Step 2:
Remove 10 bolts that secure the shroud using a 10 mm socket.

Step 3:
Using a 13 mm socket, remove the 4 bolts from the frame.

FAQ

  • Can the guard and bracket kit be used on all vehicle models?
    The guard and bracket kit is designed for specific vehicle models. Please refer to the compatibility list before purchasing.

  • What is the recommended torque for securing the nuts and bolts?
    The recommended torque values are provided in the installation instructions. Please use the specified torque for each component to ensure proper installation.

PARTS LIST –

BOLT KIT – CV-BRK3 COMPATIBLE GUARDS Check https://ex-guard.com/

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-2
Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-19

ATTENTION!! Any Ex-Guard grille guard, bracket kit, or hardware must be used with corresponding Ex- Guard components. Use of any other product or brand with Ex-Guard products will immediately void the warranty provided by Ex-Guard Industries.

TOOLS NEED FOR INSTALLATION

  • 1/2″ IMPACT DRIVER
  • 1/4″ IMPACT DRIVER
  • DRILL WITH 3/8″ DRILL BIT
  • STRAIGHT BLADE SCREW DRIVER
  • 1/2″ WRENCH
  • 9/16″ WRENCH
  • 15/16″ WRENCH
  • TORQUE WRENCH
  • 1 1/8″ DEEP SOCKET
  • 15/16″ SOCKET
  • 9/16″ SOCKET
  • 1/2″ SOCKET
  • 10 MM SOCKET
  • 13 MM SOCKET
  • 17 MM SOCKET
  • QTY 2- ZIPTIES

INCLUDED WITH THE GUARD AND BRACKET KIT

  • QTY 2 – CV-13TR-BR03 GUARD BRACKETS
  • QTY 1 – CV-13FTR-BR10R PASSENGER SIDE BRACKET
  • QTY 1 – CV-13FTR-BR10R DRIVER SIDE BRACKET
  • QTY 1 – CV-13FTR-BR05 SHROUD
  • QTY 2 – CV-13FTR-BR06
  • QTY 2 – 3/8″ X 4 BOLTS
  • QTY 2 – 3/8″ FLAT WASHERS
  • QTY 2 – 3/8″ SERRATED FLANGE NUTS
  • QTY 2 – 5/16″ X 3/4″ SERRATED FLANGE BOLTS.
  • QTY 2 – 5/16″ SERRATED FLANGE NUTS.
  • QTY 4 – 5/8″ X 2 1/2″ BOLT
  • QTY 4 – 5/8″ SERRATED FLANGE NUTS
  • QTY 2 – 3/4″ SERRATED FLANGE NUTS.

ASSEMBLY INSTRUCTION

  • STEP 1:
    USING A FLAT SCREW DRIVER,  RELEASE 2 CLIPS ON BOTH SIDES. 1 PER SIDE.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-3

  • STEP 2:
    REMOVE 10 BOLTS THAT SECURE THE SHROUD USING THE 10 MM SOCKET

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-4

  • STEP 3:
    USING A 13 MM SOCKET, REMOVE THE 4 BOLTS FROM THE FRAME.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-5

  • STEP 4:
    INSTALL A ZIP TIE TO FACILITATE INSTALLING THE BRACKET

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-6

  • STEP 5:
    INSERT ONE OF THE FOUR BOLTS REMOVED IN STEP 3, AND TIGHTEN THE ZIP TIE, UNTIL YOU CAN REMOVE / INSERT THE BOLT WITHOUT ANY TROUBLE ALIGNING

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-7

  • STEP 6:
    INSERT THE DRIVER SIDE BRACKET BETWEEN THE TWO PLATES AS SHOWN.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-8

  • STEP 7:
    RE-INSERT THE 4 BOLTS REMOVED EARLIER AND TORQUE TO 60 FT/LBS

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-9

  • STEP 8:
    POSITION BRACKET PART OVER THE TOP OF THE VEHICLE BRACE.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-10

  • STEP 9:
    DRILL A 3/8″ HOLE THROUGH THE TOP SIDE OF THE VEHICLE BRACE AS SHOWN

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-11

  • STEP 10:
    INSERT A 3/8″ X 4″ BOLT, WITH FLAT WASHER ON THE BOLT HEAD. TORQUE TO 60 FT/LBS

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-12

  • STEP 11:
    INSTALL THE BRACKETS TO THE GUARD USING THE 5/8”-11 X 2-1/2” BOLTS AND THE 15/16” SOCKET AND WRENCH. MAKE SURE TO ATTACH THE BRACKETS TO THE CENTER OF THE UPRIGHTS.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-13

  • STEP 12:
    INSERT THE GUARD BRACKETS INTO THE VAN BRACKETS BY SLIDING INTO THE RECEIVER TUBE.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-14

  • STEP 13:
    INSTALL THE 3/4-10” FLANGE NUT BY USING THE 1-1/8” SOCKET. TORQUE TO 250 FT/LBS. REPEAT ON THE OTHER SIDE.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-15

  • STEP 14:
    REMOVE THE FRONT TWO CLIPS FROM THE ORIGINAL SHROUD REMOVED AT THE START, BY USING A FLAT SCREW DRIVER

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-16

  • STEP 15:
    INSERT ON THE NEW SHROUD. POSITION AS SHOWN, AND USE 2 OF THE 10 BOLTS REMOVED FROM STEP 2 TO SECURE THE SHROUD TO THE BUMPER SKIN

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-17

  • STEP 16:
    USE THE 5/16”x3/4” BOLT AND NUT TO SECURE SHROUD TO BRACKET. ONCE THE 4 BOLTS ARE IN PLACE, TIGHTEN THE TOP 2 WITH A 10 MM SOCKET AND THE BOTTOM 2 WITH A 1/2” SOCKET.

Ford-CV-21FTR-Ex-Guard-Coverages-Archive-FIG-18

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals