Clore Automotive JNC770R Jump-N-Carry 12 Volt Jump Starter and Power Supply User Manual

Clore Automotive JNC770R Jump-N-Carry 12 Volt Jump Starter and Power

Supply

Product Information

You have purchased a 12 Volt Jump Starter & Power Supply, specifically the Jump-N-Carry brand. This jump starter is well-known and preferred by professionals worldwide for its powerful output, long service life, and durable design. The product has undergone rigorous quality control measures during manufacturing to ensure it arrives in top condition and performs to your satisfaction. Charge the unit for 24 hours through the built-in charger upon opening the box, charge after every use and charge before extended storage.

The jump starter features a sealed lead-acid battery, which must be kept at full charge. It is crucial to recharge the battery when first purchased, immediately after each use, and every three months if not used. Failure to perform these maintenance charges may significantly reduce the battery’s lifespan.

If you encounter any issues with your Jump-N-Carry, such as damaged or missing items, performance deviations, or require warranty service, please contact Technical Service at 913-310-1050. Keep your purchase receipt as it is necessary for warranty service.

It is important to note that this product contains a sealed lead-acid battery, which must be recycled properly.

Congratulations! You have just purchased a world-famous Jump-N-Carry jump starter, preferred by professionals around the world for its powerful output, exceptional service life and rugged design. We have taken numerous measures in quality control and in our manufacturing processes to ensure that your product arrives in top condition, and that it will perform to your satisfaction.
In the rare event that your Jump-N-Carry contains a damaged or missing item, does not perform as specified, or requires warranty service, please call Technical Service at 913-310-1050. Save your purchase receipt, it is required for warranty service.
This unit has a sealed lead-acid battery that should be kept at full charge. Recharge when first purchased, immediately after each use, and every three months if not used. Failure to perform maintenance charges may cause the battery life to be reduced greatly.

Safety Information

• Before using the Jump-N-Carry, thoroughly read and understand the provided instructions and safety information. Additionally, consult the instruction manual/safety information provided by the car, truck, boat, or equipment manufacturer when using the jump starter to jump start a vehicle or power any equipment. Adhering to all manufacturers’ instructions and safety procedures will minimize the risk of accidents.
• Always wear appropriate protective clothing, eye protection, and other safety equipment when working near lead-acid batteries. Avoid touching your eyes while working on or around lead-acid batteries.
• Store the clamps in their holsters, ensuring they are kept away from each other or common conductors. Improper storage of clamps may cause them to come in contact with each other or a common conductor, resulting in a short circuit and generating sufficient heat to ignite most materials.
• Exercise extreme caution when working within the engine compartment, as moving parts may cause severe injury. Familiarize yourself with and follow all safety instructions provided in the vehicle’s Owner’s Manual.
• While the Jump-N-Carry’s battery is sealed and contains no free liquid acid, the batteries being jump-started using this unit likely contain liquid acids that are hazardous if spilled.

General precautions for use:

• Someone should always be within range of your voice or close enough to come to your aid when you work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. Protective eyewear should always be worn when working near lead-acid batteries.
• If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with cold running water for at least 10 minutes and get medical attention immediately.
• Be extra cautious to reduce risk of dropping a metal tool onto a battery. It might spark or short circuit the battery or another electrical part that may cause explosion.
• Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring or the like to metal, causing a severe burn.
• Use the Jump-N-Carry for jump starting lead-acid batteries only. Do not use for jump starting dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage to property.
• NEVER charge or jump start a frozen battery.
• To prevent arcing, NEVER allow clamps to touch together or to contact the same piece of metal.
• Always keep the unit in the OFF position when not in use.
• Use of an attachment not recommended or sold by the manufacturer may result in a risk of damage to the unit or injury to personnel.
• When using the power extension cord, pull on the plug and never on the wire when disconnecting.
• Do not recharge the Jump-N-Carry with a damaged power extension cord. Replace it immediately.
• The Jump-N-Carry may be used under any weather condition – rain, snow, hot or cold temperatures.
• Do not submerge in water.
• Do not operate with flammables such as gasoline, etc.
• If the Jump-N-Carry receives a sharp blow or is otherwise damaged in any way, have it checked by a qualified service person. If the Jump-N-Carry is leaking battery acid, do not ship it. Take it to the closest battery recycler in your area.
• Do not disassemble the Jump-N-Carry. Have it checked by a qualified service person.
• The Jump-N-Carry should never be left in a completely discharged state for any period of time. Damage to the battery could be permanent, with poor performance as a result. When not in use, recharge every three (3) months.
• Always store, use and charge the Jump-N-Carry in an area where children cannot get to the unit.

Product Usage Instructions

1. Upon opening the box, charge the unit for 24 hours using thebuilt-in charger.
2. After every use, recharge the unit.
3. Before storing the jump starter for an extended period, ensureit is fully charged.
4. Always shield your eyes when using the product to prevent anypotential damage or explosion.
5. Prior to using the Jump-N-Carry to jump start a car, truck,boat, or power equipment, carefully read and understand theinstruction manual/safety information provided by the respectivemanufacturer.
6. Ensure you wear appropriate protective clothing and eyeprotection when working near lead-acid batteries.
7. Store the clamps in their holsters, away from each other orcommon conductors to prevent short circuits and potentialignition.
8. Take caution while working within the engine compartment due tomoving parts that may cause injury.
9. If the Jump-N-Carry is leaking battery acid, do not ship it.Take it to the nearest battery recycler for proper disposal.

WARNING

• Failure to follow instructions may cause damage or explosion, always shield eyes.

• Read entire instruction manual before use.

• This product can expose you to lead, which is known to the State of California to cause birth defects or other reproductive harm, and Vinyl-Chloride, Styrene and Acrylonitrile, which are known to the State of California to cause cancer. For more information
  go to www.P65Warnings.ca.gov.

• CONTAINS SEALED LEAD ACID BATTERY. BATTERY MUST BE RECYCLED.\

Features

• The Jump-N-Carry provides plenty of power for starting vehicles – more than enough to start most cars, trucks, SUVs and light duty commercial vehicles.
• The unit contains the latest technology with its 12 Volt sealed, non-spillable battery and may be stored in any position.
• The unit features a master ON/OFF switch. The unit should be kept in the OFF position at all times when it is not in use.
• The unit features extra-long cable reach to allow safe, easy positioning while jump starting. Always re-wrap cables and re-holster the clamps after each use.
• The unit will power most 12 Vdc accessories equipped with a male 12 Volt plug. The DC outlet features automatic overload protection.
• The unit will provide USB power to small electronics, with 1.1A and 2.1A output options available.
• The unit features a high intensity LED light to assist when jump starting in the dark or at other times when additional light is needed.

Battery Status Indication

Press and hold the “V” (Voltage Status) Button to show the battery status on the display. The message seen on the display corresponds to the battery’s state of charge:

• If the battery’s voltage is less than 12.4V, the display will flash the voltage and then show CHG continuously, indicating the unit should be charged immediately.
• If the battery’s voltage is between 12.4-12.8V, the display will show the battery’s voltage and then flash CHG three times, indicating the unit is in need of charge.
• If the battery’s voltage is above 12.8V, the display will alternately flash the battery’s voltage and FUL, indicating that the unit is fully charged.

Recharging

Note: Upon initial purchase, charge your Jump-N-Carry until the display reads FUL.
Recharge the Jump-N-Carry using a household extension cord connected to the built-in charger in the back of the unit.

1. Connect the female end of the extension cord to the charger plug on the back of the unit. The charger plug has two blades and resembles a standard household plug that would fit into a 120 Vac wall receptacle.
2. Connect the male end of the extension cord to the AC outlet.
3. Charge until the dispay reads FUL.

Note: The unit can remain connected to AC power indefinitely without adverse consequences. The charging system is fully automatic and will only consume power as need to maintain the onboard battery.

Note: If the display shows Er3 when you connect an extension cord to charge, the internal battery is either damaged or too discharged to accept a charge.

Jump Starting Instructions

Safety Check List
Always Perform this Step Before Use to Ensure Safe Operation.

1. Check to make sure that the clamps and cables are in good working order. Signs that the clamps may be damaged include, but are not limited to the following:
   • Burn Marks on the Jaws
   • Damaged clamp handles
   • Damaged clamp springs
   • Damaged cables where copper wiring may be exposed (insulation jacket deteriorated, cut or missing)
2. Check to make sure the case is not swollen (a sign of damaged batteries). Verifying these simple check points before every use will keep your jump starter safe to
   use and increase its service life.

Note: For optimum performance, do not store your Jump-N-Carry below 50°F when using as a jump starter. NEVER charge or jump start a frozen battery.

1. Use in a well ventilated area.

2. Shield eyes. Always wear protective eyewear when working near batteries.

3. Review this instruction manual and the instruction/safety manual provided by the manufacturer of the vehicle being jump started.

4. Turn vehicle ignition off and ensure unit ON/OFF switch is in the OFF position before making cable connections.

5. Clamp the positive (red +) clamp to the positive terminal on the vehicle battery (for negative ground system), or an alternate vehicle starting point as recommended by vehicle manufacturer.

6. Clamp the negative (black –) clamp to the vehicle ground (non-moving metal part, such as the vehicle frame).
   Note: If warning buzzer beeps, do not advance to step 7. Determine source of error. Display will show one of two error codes: Er1 – reverse polarity, Er2 – over-voltage (connected to a battery above 16VDC). Resolve the error source before proceeding to the next step.

7. Turn unit ON/OFF switch to ON position.

8. Make sure the cables are not in the path of moving engine parts (belts, fans, etc.).

9. Stay clear of batteries while jump starting.

10. Start the vehicle (turn on the vehicle ignition).
    Note: if the vehicle doesn’t start within 6 seconds, let the Jump-N-Carry cool for 3 minutes before attempting to start the vehicle again or you may damage the Jump-N-Carry.

11. When the vehicle is started, turn ON/OFF switch to OFF position, disconnect the negative (–) battery clamp from the vehicle frame and return it to its holster.

12. Disconnect the positive (+) clamp and return it to its holster.

12 Volt DC Power

Your Jump-N-Carry is an essential tool for all who replace automobile batteries. Most vehicles have electronic components with memory, such as alarm systems, computers, radios, phones, etc. and when the vehicle’s battery is replaced, the memory is lost. However, if the Male-Male Extension Cord is connected from the Jump-N-Carry to the 12 Volt outlet on the vehicle, the memory can be saved.

Note: To use the Jump-N-Carry for this purpose, the chosen outlet must be live whenthe vehicle is turned OFF. On some vehicles, 12 Volt outlets are deactivated when the vehicle is turned OFF.

Your Jump-N-Carry is also a portable power source for all 12 Vdc accessories equipped with a male 12 Volt plug. The DC outlet on the Jump-N-Carry has automatic overload protection.
When your Jump-N-Carry is used with a DC to AC power inverter, it can operate appliances normally powered by 120 Vac or 220 Vac. Recommended inverter for the portable power source is 400 watts maximum. For more information, contact your nearest Jump-N-Carry dealer.

USB Power

Your Jump-N-Carry features two USB outlets, one 2.1A maximum output and one 1.1A maximum output.
To active the USB outlets, quickly press the Light Button on the control panel. You should see the USB status light, located between the USB outlets, light green. This indicates the USB outlets are now powered.

LED Work Light

Your Jump-N-Carry is equipped with a high intensity LED work/flash light for use when jump starting at night or when additional light is needed to complete a task. To turn the light on, press and hold the Light Button on the control panel for 3 seconds. A second quick press switch the light’s output to flashing. A third quick press will turn the light off.

Performance and Temperature

Performance of your Jump-N-Carry will depend upon several factors:

• A good, solid connection between the Jump-N-Carry clamps and the battery and ground connections are a must. Moving the clamps back and forth while connecting to the battery will help create a better connection.
• Clean connections between your vehicle or equipment battery and its terminals are very important. For an optimal connection, corrosion (soft grayish-white build-up) on battery terminals must be removed. With the ignition turned off, disconnect the battery cables and clean the terminals and battery posts with a baking soda solution.
• All batteries are affected by temperature changes, and the small, lightweight battery in the Jump-N-Carry is more sensitive to storage temperature than a standard automotive battery. Temperatures below 70ºF decrease amperage output. The ideal storage environment is room temperature, or 68ºF.

Troubleshooting/FAQs

• Q. What should I do if the Jump-N-Carry will not hold a charge?
  A. Load test the battery. After fully charging the battery (see “Recharging” section), apply a 100 amp load (through the clamps) to the unit for a period of 6 seconds, while monitoring the battery voltage. The battery is good if the voltage at the end of the load is 9.5 Vdc or higher.

• Q. What is the ideal use for the Jump-N-Carry?
  A. The Jump-N-Carry performs strongly when a vehicle’s battery needs an extra boost because a light or radio was left on, or when a vehicle has been sitting for a long period of time. The Jump-N-Carry will start vehicles without any other batteries present, but the primary use is for an extra boost.

• Q. Will the Jump-N-Carry start every vehicle?
  A. No. In addition to a dead battery, a car may have other mechanical problems that would prevent the Jump-N-Carry from starting the vehicle.

• Q. How often should I recharge the Jump-N-Carry?
  A. To maximize battery life, charging after every use is recommended. The Jump-N-Carry should not be left in a discharged state. The battery in the Jump-N-Carry has no memory problems and should not be treated as a rechargeable tool (cordless drills, camcorders, etc.).

• Q. How many jump starts can I get from the Jump-N-Carry before recharging?
  A. A large number of factors affect this answer, including the following: the length of time for each jump start, the charge level of the original battery, the length of time between jump starts, the temperature of the vehicles being jump started (winter cold makes for difficult starting), the size of the engines (4-cycl, 6-cycl, 8-cycl, etc.), the mechanical condition of the engine and starter, and more. These factors must all be weighed on an individual basis before an accurate answer can be given. It’s feasible to get 10-30 starts (individual’s results will differ) from a single charge, but this violates the rule of immediate charging after every use.

• Q. After jump starting, can I leave the unit hooked to the battery to recharge the Jump-N-Carry while the engine is running?
  A. No. Attempting to recharge the Jump-N-Carry by this method  recommended. Vehicle alternators output anywhere from 25-125 amps. This charging rate greatly exceeds the recommended recharging rate for Jump-N-Carry. Charging by this method will result in overcharging the Jump-N-Carry battery, and may void the product warranty.

• Q. What accessories can be used in the optional 12 volt outlet?
  A. Any accessory up to 12 amps can be powered by the Jump-N-Carry. This unit is equipped with an automatic reset circuit breaker, should the current exceed 12 amps. At the same time, this limits any recharge current through the 12-volt outlet to 12 amps. One can power almost any 12-volt tool or accessory (examples: impact wrenches, fans, radios, cellular phones, navigation equipment, camcorders, emergency power, trolling motors, coolers, small refrigerators, etc.).

• Q. Can the Jump-N-Carry battery be replaced?
  A. Yes, call Technical Service at 913-310-1050 (U.S.).

• Q. Can the Jump-N-Carry be recycled?
  A. Yes, the environment was one of our main concerns in the development and design of the Jump-N-Carry. Most battery outlets can dispose of this product at its life’s end. In fact, your Jump-N-Carry contains a sealed, non-spillable lead acid battery and proper disposal is required by law. See Battery Removal and Disposal Instructions.

• Q. I have a regular 10 amp battery charger, can I use it to recharge the Jump-N-Carry?
  A. No, only the methods reviewed in the “Recharging” section should be used.

• Q. Is the Jump-N-Carry goof proof?
  A. No, jump starting instructions must be followed. Read and understand all safety and operating instructions in this manual and those found in the owner’s manual of any vehicle being jump started before using your Jump-N-Carry.

Testing The Battery

After fully charging the battery (see “Recharging” section), apply a 100 amp load to the unit for a period of 6 seconds, while monitoring the battery voltage. The battery is good if the voltage is 9.5 Vdc or higher.

Storage

The Jump-N-Carry may be stored virtually anywhere, and in any position. However,
take precautions to ensure that the positive and negative clamps do not come into contact with each other or a common metal surface. We recommend storing the Jump-N-Carry in the box in which it was originally received. Always be sure to re-wrap cables and re-holster clamps after each use and prior to storage.

Battery Replacement and Disposal

This unit contains a sealed non-spillable lead-acid battery. This battery must be recycled. Consult your state or local government concerning regulations for proper disposal.

The battery inside this product is a sealed lead-acid battery. It is required by law to be removed and recycled or disposed of properly. While there are federal regulations that must be complied with throughout the United States, your individual state or local governments may have  dditional regulations to be followed.
When the battery in this product is in need of replacement, remove it according to the instructions provided below and take it to your local recycling center for proper recycling or disposal. If you don’t have a local recycling center that handles sealed lead-acid batteries, contact your local environmental agency for instructions.

Removal instructions:
Begin by making sure that both clamps are securely placed in a position that ensures they will not come into contact with each other.

1. Lay the Jump-N-Carry down on its front. On the back of the unit, locate the 13 screws that hold the case together (including a total of 6 screws located in the cable management tracks).
2. Remove the screws, then lift off the back half of the case, lifting first from the bottom.
3. On the top of the battery are two terminals, each with wires connected to them. Disconnect these wires from the battery by removing the bolts that hold them to the battery terminals. To prevent accidental arcing, be careful not to touch both battery terminals with the tools being used to remove the bolts.
4. Lift the battery out of the front half of the case.

Jump-N-Carry Limited Warranty

Clore Automotive warrants this product to be free from defects in material or workmanship for a period of one year from the date of original end user purchase.
This warranty extends to each person who acquires lawful ownership within one year of the original retail purchase, but is void if the product has been abused, altered, misused or improperly packaged and damaged when returned for repair.
This warranty applies to the product only and does not apply to any accessory items included with the product which are subject to wear from usage; the replacement or repair of these items shall be at the expense of the owner.
THE TERMS OF THE CLORE AUTOMOTIVE LIMITED WARRANTY CONSTITUTE
THE BUYER’S SOLE AND EXCLUSIVE REMEDY. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS EXPRESS WARRANTY. AFTER 1 YEAR FROM DATE OF PURCHASE, ALL RISK OF LOSS FROM WHATEVER REASON SHALL BE PUT UPON THE PURCHASER.
CLORE AUTOMOTIVE SHALL NOT BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES UNDER ANY CIRCUMSTANCES: CLORE AUTOMOTIVE’S LIABILITY, IF ANY, SHALL NEVER EXCEED THE PURCHASE PRICE OF THIS PRODUCT REGARDLESS OF WHETHER LIABILITY IS PREDICATED UPON BREACH OF WARRANTY (EXPRESS OR IMPLIED), NEGLIGENCE, STRICT TORT OR ANY OTHER THEORY.
Some states do not permit the limitation of warranties or limitation of consequential or incidental damages, so the above disclaimer and limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For Warranty or Service

If this product fails within the first 30 days after retail purchase due to a defect
in material or workmanship, return it to your place of purchase for an exchange. From day 31 to day 365 after retail purchase, your product should be sent to Clore Automotive at the address below for service. A valid, dated sales receipt is required to obtain service under this warranty.

• Jump Starter Repair
  • 8600 NE Underground Drive, Pillar 248
  • Kansas City, MO 64161
  • 800.328.2921
  • 913.310.1050
• For best service and to receive periodic product updates, follow the instructions below to register your purchase:
  • please visit: www.cloreregistration.com
  • Click on the Jump-N-Carry logo. Complete the information in the web form and click “submit.” It’s that easy!
• For answers to questions concerning use, out-of-warranty service, or warranty/service information on this or other Clore Automotive products,
  • contact us at 800.328.2921
  • (913.310.1053).

References

• Home - Clore Automotive
• Clore Automotive Registration
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>