OMT V20230307 Tailgate Assist Instruction Manual
- May 15, 2024
- OMT
Table of Contents
Tailgate Assist
Instruction Manual Read
Carefully Before Use
Keep for Future Reference
Safety Information
Warning!
- The instructions provided herein are only for general information. ALWAYS use this product in full compliance with your vehicle’s service manual.
- DO NOT allow children or those unfamiliar with this product and its compatible vehicle models to use it. Do not use while under the influence of alcohol, drugs, or any medication that negatively affects your judgment or reflexes. Keep children and bystanders away during use.
- Dress properly for automotive servicing. Do not wear loose clothing or jewelry and keep hair, clothing, gloves, hoses, and tools away from any moving parts during use.
- Do not overreach. Keep proper footing and balance at all times.
- DO NOT use excessive pressure with this product and do not force it or its attachments.
- Maintain this product. Check for misalignment, binding, wear, or other damage before use.
If any damage is detected, repair or replace the problematic components before further use.
In a large shop, mark such tools DO NOT USE until they have been repaired. Only replace components with identical parts.
Specifications
Material | A3 Steel |
---|---|
Fitment | 2022–2023 Ford Maverick |
Net Weight | 15.1 oz. |
Parts List
No. | Name | Qty. |
---|---|---|
A | Shock | 1 |
B | Upper Ball Mount Plate Lower Ball Mount Plate | 1 |
D | Spare Spring Clips | 1 |
E | M8 Bolt | 2 |
F | Tailgate Fastener | 1 |
G | T50 Torx Wrench | 1 |
H | M5 Hex Wrench | 1 |
I | Threadlocker | 1 |
Installation
Note: This product can only be installed on the driver’s side of the car.
-
Remove the tailgate cable by pulling on the spring clip and using a T50 torx wrench (G) to remove the cable bolt.
-
Apply a small amount of threadlocker (I) to the threads of the bolt removed in the previous step.
Then, insert the bolt through the hole in the upper ball mount plate (B) and tighten it with the T50 torx wrench. -
Attach the cable back to the cable bolt.
-
Thread the bolt through the hole in the lower ball mount plate (C) and into the tailgate fastener (F).
Ensure that the notches on the bolt are facing towards the lower ball mount. -
Align the tailgate fastener with the slot in the tailgate, insert the tailgate fastener into the slot, and insert the M8 bolt (E). Turn it 90° to align the tailgate fastener’s notches with the edges of the slot. Use the provided M5 hex wrench (H) to tighten the bolt while pulling out on the lower ball mount plate.
-
Once the lower ball mount is securely attached, attach the small end of the shock (A) to the lower ball mount plate.
-
Attach the larger end of the shock to the upper ball mount plate.
-
Remove the bottle opener on the driver’s side of the tailgate by using a T30 torx wrench to unscrew the two screws attaching it. If the bottle opener is not removed, it will interfere with the shock and prevent the tailgate from closing.
Maintenance
-
Clean these tools with a dry brush or cloth after use. If rinsing is necessary, dry all parts completely before storage. Clean the tailgate assist as needed. Never use abrasive cleaners or caustic chemicals with any part.
-
Check the tailgate assist and these tools periodically for any looseness, wear, or damage.
Tighten, repair, or replace any problematic parts before further use. -
If the assist will not be used for an extended period of time, remove and store in a cool dry place inaccessible to children.
Contact Us
Thank you for choosing our products! If you have any questions or comments,
contact us at help@cs-supportpro.com and
we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the
appropriate app on your smartphone to scan the QR code to the right.