OMT V20230209 Oil Filter Wrench Set Instruction Manual
- May 15, 2024
- OMT
Table of Contents
OMT V20230209 Oil Filter Wrench Set
Product Information
Specifications
- Material: Aluminum, Chromium-Vanadium Steel
- Length Wrench Drive: 8 in. (20.4 cm) 9.5 mm
- Net Weight: 3.4 lb. (1.56 kg)
FAQ
- Q: How often should I change my oil filter?
- A: It is generally recommended to change your oil filter with every oil change, typically every 5,000 to 7,500 miles or as per your vehicle manufacturer’s recommendations.
- Q: Can I reuse an oil filter?
- A: It is not recommended to reuse oil filters as they can accumulate debris and contaminants over time, potentially leading to engine damage or reduced performance.
Safety Information
Danger
- The instructions provided herein are only for general information. ALWAYS perform all repairs in full compliance with your vehicle’s service manual. Particularly, ALWAYS tighten parts to the torque ranges specified in the service manual. After any repair, test your engine and vehicle in your workshop and at low speed before returning to normal use.
- DO NOT allow children or those unfamiliar with this product and its compatible engines to use it. Do not use while tired or while intoxicated with alcohol, drugs, or medication. Keep children and bystanders away during use.
- Stay alert, watch what you are doing, and use common sense when using this product. Keep your work area clean and well lit. Cluttered and dark areas invite accidents.
- ALWAYS wear personal protective equipment (PPE) suitable for your task. Always wear ANSI-approved eye and hand protection. Other equipment such as nonslip footwear will usually be needed as well. Dress properly for automotive servicing. Do not wear loose clothing or jewelry. Keep hair and clothing away from moving parts.
- ALWAYS activate your vehicle’s parking brake before any engine work. If your vehicle requires one or both front wheels to be removed to provide access to the engine, use jacks and jack stands able to fully support the necessary weight.
- Disconnect your vehicle’s battery before beginning work. Large metal tools can cause shorts and electric shock during accidental contact with either terminal.
- Dispose of the used filter and oil according to local regulations. ALWAYS fully drain the oil filter before disposal.
- Maintain this product. Check for misalignment, binding, wear, or other damage before use. If any damage is detected, repair or replace the problematic components before further use.
Parts List
- 1 × Oil Filter Wrench
- 9 × Oil Filter Wrench Adapters
Operation And Maintenance
Operation
- Park your vehicle on level ground and activate its parking brake. The oil should be slightly warm but not hot. If your engine is cold, run it a few minutes. If your engine is hot, allow time for it to cool. Turn off your engine and disconnect the battery.
- If you will be performing a full oil change, drain the oil pan according to your vehicle’s service manual now.
- Find the oil filter. Position your catch basin below it, as some oil will leak during the change.
- Select the correct adapter for your vehicle and attach it to the provided wrench.
- Fit the adapter onto your filter and turn counterclockwise to loosen and remove it.
- Leave your old filter facedown in or above your catch basin to drain completely for the next 24 hours before disposal.
- Lubricate your new filter’s gasket with a small amount of oil and thread it carefully into place by hand.
- Finish installing the filter according to your service manual’s instructions, tightening it only to the recommended torque.
- Top up your motor oil, reconnect your battery, and check for any leaks or other problems before resuming full use of your vehicle.
Maintenance
- For best results, clean with a mild detergent and soft cloth after each use. Do not use caustic chemicals or harsh abrasives. Rinse entirely clean and allow time to dry completely before further use.
- Check all parts periodically for any signs of wear or damage. Repair or replace any problematic components before any further use.
- If these tools will not be used for an extended time, store in a cool dry place inaccessible to children and away from direct sunlight.
Specifications
| Material | Aluminum, Chromium-Vanadium Steel |
|---|
Wrench
| Length| 8 in.| 20.4 cm
Drive| ⅜ in.| 9.5 mm
Case Dimensions| 12.3×9.1×2.6 in.| 31.2×23.2×6.6 cm
Net Weight| 3.4 lb.| 1.56 kg
Contact Us
Thank you for choosing our products! If you have any questions or comments,
contact us at help@cs-supportpro.com and
we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the
appropriate app on your smartphone to scan the QR code to the right.
Scan
Documents / Resources
| OMT
V20230209 Oil Filter Wrench
Set
[pdf] Instruction Manual
V20230209, LQW-A001-00, V20230209 Oil Filter Wrench Set, Oil Filter Wrench
Set, Filter Wrench Set, Wrench Set, Set
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>