signify IB51914921 SurgiCare Troffer Installation Guide
- June 17, 2024
- signify
Table of Contents
signify IB51914921 SurgiCare Troffer Installation Guide
DISCLAIMER OF LIABILITY: ALKCO assumes no liability for damages or losses of
any kind that may arise from the improper, careless, or negligent
installation, handling or use of this product.
IMPORTANT: Read carefully before installing fixture. Retain for future
reference.
NOTICE: These instructions do not claim to cover all details or variations in
the equipment, procedure, or process described, or to provide directions for
meeting every possible contingency during installation, operation or
maintenance. When additional information is desired to satisfy a problem not
covered sufficiently for user’s purpose, please contact your nearest
representative.
NOTICE: Proper grounding is required to insure personal safety. Carefully
observe grounding procedure under installation section. NOTICE: Fixture may
become damaged and/or unstable if not installed properly. Note: Specifications
and dimensions subject to change without notice.
GENERAL: Upon receipt of fixture thoroughly inspect for any freight damage,
which should be brought to the attention of the delivery carrier. Compare the
catalog description listed on the packing slip with the fixture label on the
housing to assure you have received the correct merchandise.
SGTF FIXTURE MOUNTING
Install the mounting brackets by removing the door and the LED board plate (FIG. 1). Insert cage nuts in the back of the housing (4 corners). Insert the fixture in the sheetrock cutout. From inside the fixture, slide the (4) brackets through the slots on the sides of the fixture. Make sure the brackets are resting on the ceiling structure (FIG. 3). Secure the brackets with screws through cage nuts in housing (FIG. 2 and 2.1).
Note: Bracket orientation (bend up or down) is determined by ceiling thickness.
SGTG FIXTURE MOUNTING
Install fixture so it sits on the grid, top flange must rest on the T-GRID surface (FIG. 4 and 4.1).
WIRING
For fixture wiring, remove access plates on top of the housing (FIG. 5). The wires are attached to access plates with nylon zip ties, identify quick- connectors and connect to facility power according to electrical codes.
THERMAL PROTECTOR INSTALLATION
Identify thermal protectors on one side of the fixture (FIG.6 and 6.1), remove split ring bushing and discard (FIG. 6.2) and push thermal protector in the hole until it snaps into place (FIG.6.3). Note: Not all fixtures require thermal protectors.
SECURITY BRACKETS (Optional accessory for SGTG)
Once the fixture is located on the grid, install the security brackets in the
positions shown (FIG. 7). Make sure the screw (self drilling) for each bracket
is in the right position (FIG. 7.1).
⚠ CAUTION: This fixture is designed for permanent installation in ordinary
(non-hazardous) locations in accordance with the national electrical code and
all applicable local codes. Do not use in areas of limited ventilation or in
high ambient enclosures. The led and fixture operate at high temperatures.
Contact with combustible materials can cause fire and personal contact can
cause severe burns.
FCC Statement Note:
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Signify North America Corporation 400 Crossing Blvd, Suite 600 Bridgewater, NJ
08807, USA P: 855-486-2216
www.signify.com
Signify Canada Ltd. 281Hillmount Road Markham, ON, Canada L6C 2S3 P:
800-668-9008
© 2023 Signify All Rights Reserved Printed in USA Imprimé aux États-Unis
Impreso en los EE. UU. Publication No. IB51999223 March 27 2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>