YEELIGHT YLDD007 Lightstrip Pro User Manual
- June 15, 2024
- Yeelight
Table of Contents
YEELIGHT YLDD007 Lightstrip Pro User Manual
Product Description
Plug will be subject to sales territory standard. Picture shown above is for
reference onl
The Extension needs to purchase separately.
Setup Instructions
Plug into the adapter, rotate by 45 degrees clockwise and snap into place
Insert the end with 4 pins into the corresponding socket and fasten the
buckle.
Clean the installation surface, paste and fix the light strip
If the light strip needs to be extended, please purchase Eyesight Lightstrip Pro Extension. Open the tail end buckle of the light strip, remove the tail plug, connect the end with 4 pins of the extension strip with the tail end of the original strip, and tighten the buckle.
Install the tail plug at the tail end of the extension part and fasten the
buckle to complete the connection
Connect and plug in the power supply.
To ensure that the functions can work normally:
- After connecting the extension strip, ensure the tail plug is correctly plugged into the tail end of the light strip.
- After cutting the light strip, set the length of the light strip in the app (Mijia app QR code.)
Instructions for Use
ap “ ” to turn the light strip; tap “ ” again to turn off the light strip.
Tap and hold “ ” to choose your favorite color.
Double tap “ ” to choose your favorite Dream Color mode
Parameters
Model No.:
YLDD005
Operating Temperature:
-10 ~ 40°C
Frequency Bands:
2412MHz – 2472MHz (Wi-Fi) 2402MHz – 2480MHz (BT)
Rated Input:
24 VDC, 0.21A, 5.1W (80in, 2m) 24 VDC, 0.88A, 21W (400in, 10m)
Rated Input (Adapter)
: 100-240V ~ 50/60Hz, 0.06A, 5.5W (80in, 2m) 100-240V ~ 50/60Hz, 0.25A, 24W
(400in, 10m)
Maximum Output Power:
18 dBm (Wi-Fi) 6 dBm (BT)
Connectivity :
Wi-Fi IEEE 802.11 b/g/n 2.4GHz, Bluetooth 4.2 BLE
System Requirements:
Android 4.4 & iOS 10.0 or above
Intelligent Control
This product works with Mi Home / Xiaomi Home app. Control your device, and interact it and other smart home devices with Mi Home / Xiaomi Home App.
- Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search “Mi Home / Xiaomi Home” in the app Store to download and install it.
- Open Mi Home / Xiaomi Home app, tap “+” on the upper right, and then follow prompts to add your device
Note: The version of the app might have been updated, please follow the instructions based on the current aspersion
Works with Mejia
“Works with Mejia” means that the product can be control by Mi Home app or Xiaomi. Please note that “Works with Mejia” only performs software-level verification. Xiaomi and Mejia are not responsible for the manufacturinstandard implementation and quality supervision of the products and enterprises
Apple HomeKit Smart Control
- Open the Home APP in your iPhone or iPad.
- Click “+” button and add accessory as per the prompts in the app. Scan the QR code on the right or under the product base. Alternatively, input the 8-digit code shown above the QR code to complete the access.
- Make sure the Wi-Fi network is available and you can get access to the internet properly. This product is not compatible with 5G network.
- To ensure proper HomeKit compatibility, it is recommended to use iOS 9 or above.
- HomeRight codes are indicated under the base of controller. Please be noted that HomeRight codes are required for reset every time.
Apple is the trade mark of Apple LLC.
Use the Works with Apple badge means that an accessory has been designed to
work specifically with the technology identified in the badge and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance
with safety and regulatory standards
Apple, HomeRight, iPad, and iPhone are trademarks of Apple Inc., registered in
the U.S. and other countries.
To control this HomeRight-enabled accessory, the latest version of iOS or pads
is recommended.
Home hub
customer who owns an Apple TV (4th generation or later) with tvOS 10 or later, an iPad with iOS or later, or me Pod can control HomeRight-enabled accessories away from home and automatically through triggers such as time of day, location, sensor detection, or the action of an accessory.
How to Reset
Disconnect the power. Press the power button and reconnect to the power supply
without release. Hold the button for five seconds until the light strip flows
in red, green, and blue, and turns to yellow. Then, release the button. Reset
is completed.
Please reset the light strip before using it in a new network environment.
Warnings
- Check the voltage before using the product. Improper voltage may damage the product and cause potential safety hazards.
- For indoor use only.
- To prevent early product failure, the light strip should only be installed in operating environment ranging between 10°F to 104°F (-10°C to +40°C)
- The light strip is not waterproof.
- Regularly check the cable, the power supply, and all other parts. Do not use this luminaire when any part is damaged.
- The external flexible cable or cord of this luminaire cannot be replaced. Do not use the luminaire when the cable or cord is damaged.
- The light strip is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Do not disassemble the product privately.
- Keep the light strip away from kids under 3-year-old.
- Max interconnected 40in (10m).
- Do not bend the LED inside the light strip is more than 90 degrees to avoid any possible damage.
- Do not connect the light strip to the power supply when it is in the package.
- Interconnection shall be made only by the use of the supplied connectors. Any open end must be sealed-off before use.
- Do not use the light strip when covered or recessed into a surface.
- Do not open or cut the light strip.
- Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.
EU Declaration of Conformity
Qingdao Eyeblink Information Technology Co., hereby declares that type Y00409 devices are in conformity with EU Directives. The full text of the EU Declaration of Conformity is available at the following web address: https://edshop.edsystem.cz/prohlaseni-oshode/article-28393
WEEE
This product must not be disposed of as normal household waste in accordance with the EU Directive on Wastectrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise because by inappropriate waste handling of this product. Contact your local authority or the nearest collection point further details. Improper disposal of this type of waste may result in fines in accordance with national regulations
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>