BUTURE BR800 Car Battery Jump Starter User Manual
- June 14, 2024
- BUTURE
Table of Contents
User Manual
BR800 Car Jump Starter
Package Content
|
---|---
BUTURE BR800 Jump Starter| Smart Jumper Cables
|
Charging Cable| User Manual
Product Know Your
1. ON/OFF Button
2. Battery Indicator
3. 5V/2.4 Ouput| 4. Flashiight
5. Input
6. Jump Staring Port
---|---
Powerful Circuit Protection System – Smart Clamps
- Red Jumper Cable (+)
- Black Jumper Cable (-)
- Smart Clamp Plug
Technical Details
| Model | BR800 |
|---|---|
| Capacity | 12800mAh |
| Input | 5V/2A |
| Output | 5V/2.4A |
| Dimensions(LWH) | 153.585.127.8mm |
| Overload/Discharge Fuse | ≤13V±0.3V |
| Working Temperature | -20 °C∼ 60 °C / -4 F ∼ 140 °F |
| Backflow Protection | ≥ 12.6V±0.3V |
| Short circuit fuse protection | √ |
| Short circuit fuse protection | √ |
Operation
Power indicator light
Press the power button to check the capacity of the Jump starter. Indicator
Lights as below picture (25% ,50%,75%,100%).
Recharge the Jump starter
Note:
The wall charger or car charger is not included in the package, you can use
a universal USB charger to recharge the unit, such as your phone or pad
charger ( 5V/2A is suggested ).
At Home:
- Plug the charging cable into any USB wall adaptor (not included).
- Connect the charging cable (included) to the unit.
In Car:
- Plug the USB car adapter (not included) into an available 12V socket.
- Connect the charging cable (included ) to the unit.
Note:
It is recommended to recharge the Jump starter every 3-4 months to maintain
the efficiency and prolong the service life of the internal battery even if
the unit has not been used.
Charging your devices from the output
Use the original manufacturer’s charging cable that came with your device
and plug it into one of the output ports. You can charge your phone or tablet
via the output at 5V/2.4A. Press the power button once tobegincharging
yourdevice. The power level indicator will show the battery level. To check
the power capacity again simply press the power button once.
To Jump Start Your Car
To jump start the vehicle battery, put the vehicle in park (neutral if the
vehicle has a manual transmission) and engage the emergency brake. Locate the
battery for the vehicle and follow the steps listed below.
Jump cables are color-coded, RED for POSITIVE (+) and BLACK for NEGATIVE (-)
Do not mix up the cables or allow the metal ends to touch together because
this may damage the battery charging system and/or electronics on a vehicle.
NOTE:
This product is for 12V car only. Check to make sure that 3 or 4 indicator
lights are illuminated (battery level is above 50%) before you use it to start
your car.
Step1:
Insert the plug of the smart battery clamp completely into the jump starter.
If the green and red light indicators on the battery clamp are flashing
alternately, you are safe to move on to the next step. Step 2:
Connect the red clamp to the positive terminal (+) of the car battery and
connect the black clamp to the negative (-) of the car battery. If the
indicator light of the smart clamp is solid green, you can move on to the next
step.
However, if the red indicator light is on:
- The battery clamp may be connected in reverse. In this case, you need to disconnect the battery clamp from the vehicle and the jump starter.
- Adjust the clamps for maximum contact with the battery terminals.
Step3:
Start Your Car
If you failed to start your car, you need to disconnect the battery clamp
from the vehicle and the jump starter. Wait for at least 30 seconds, then try
again. Step 4:
Once your car is started, remove the battery clamp from the car battery and
the jump starter within 30 seconds.
In any of the following situations, the smart clamp turns protection on:
| Situations | LED indicator | Solutions |
|---|---|---|
| Before connection to car battery | Flashing red/ green light | Ready to work |
| After connection to car battery | Solid green light | Work status |
| Solid red light | Power is low. Recharge the product in time or replace the |
jump starter.
Solid red light with beep| 1. Over-heat protection is on
–remove the clamps from car battery and wait for flashing red/green light.
2. Battery clamps are reversely connected
–red clamp to car positive terminal (+) and black to the negative (-).
3. The clamp is short-circuited
–make sure the two clamps are not connected together, otherwise replace the
jumper cables.
Flashing red/ green light| Reverse charging protection is on — remove the
damps promptly after successful start.
Flashing green light| Connection timed out.
Please reconnect the clamps.
Still can’t start your car?| Please contact
support@ibuture.com
Warnings:
- When jump-starting a vehicle, please ensure that the blue plug is securely fitted into the jump start socket on your jump starter.
- Do not allow this product in water.
- Do not operate the product in explosive atmospheres, such as in the presence of flammable liquid, gas or dust.
- Do not modify or disassemble the product.
- If battery leakage occurs, take it to your local battery recycling center for disposal do not attempt to use it.
- This car jump starter is for use with 12V vehicles only.
Battery Disposal
The battery is self-contained and not consumer replaceable. The battery must be disposed properly when it no longer holds a charge. Proper charging practices will increase the life of the product.
Warranty
Our company provides customers with warranty of 24 months from the date of purchase.
Contact US
For additional assistance or warranty cover claim, please contact us:
E-Mail: support@ibuture.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>