VITEK VT-8266 BK Men Electric Shaver Instruction Manual

VITEK VT-8266 BK Men Electric Shaver Instruction Manual

MEN SHAVER VT-8266 BK

DESCRIPTION

1. Shaving block
2. Shaving block release button
3. Body
4. Power switch with the lock button
5. Charging indicator
6. Power cord connector socket
7. Trimmer lock
8. Power cord
9.  Protective cap
10. Brush for cleaning

SAFETY MEASURES

Before using the unit, read this instruction manual carefully and keep it for future reference.
Use the unit for the intended purposes only as specified in this manual. Mishandling of the unit may lead to its breakage and cause harm to the user or damage to his/ her property.

• Before charging the battery for the first time, make sure that the voltage in your mains corresponds to unit operating voltage.

• Use the shaver only for the intended purposes.

• Do not leave the operating unit unattended.

• Switch the shaver off during pauses in operation or when you are not using it.

• Do not charge the unit in places with high humidity and temperature.

• Charge the battery at the temperature from 0° C to +35° C and relative humidity not more than 80%.

• To charge the shaver use only the power cord supplied with the unit.
  Do not use the power cord if the insulation or the plug is damaged.

• Do not place the power cord near hot surfaces or open flame.

• Do not immerse the shaver, the power cord and the plug into water or any other liquids.

• When unplugging the unit, pull the plug but not cord.

• To avoid injury do not use the shaver with damaged stationary shaving headnets or rotating blades.

• Do not allow children to use the unit as a toy. Keep the unit away from children.

•  For children safety reasons do not leave polyethylene bags used as a packaging unattended. Attention! Do not allow children to play with polyethylene bags or packaging film.

Danger of suffocation!

• This unit is not intended for usage by children.

• The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• Do not attempt to repair the unit. Do not disassemble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply t any authorized service center at the
  contact addresses given in the warranty certificate and on the website www.vitek.ru.

• Transport the unit in the original package only.

• For environment protection do not discard the unit with usual household waste after its service life expiration; apply to a specialized center for further recycling.

• Keep the unit out of reach of children and disabled persons.
  THE UNIT IS INTENDED FOR HOUSEHOLD USAGE ONLY

USING OF MEN SHAVER

After unit transportation or storage at low temperature keep it for at least 3 hours at room temperature before switching on.

Charging (pic. 1)

Before using the shaver for the first time or after a long period of inactivity the battery needs to be charged for 8 hours.

• Insert the power cord (8) jack into the connector (6) and connect the plug to the mains, the charging indicator (5) will light up.
• Battery recharging cycles should not exceed two hours.

Note:
– Recharge the battery only after its complete discharge.
– Charge the accumulator batteries at the temperature from 0° C to +35° C.
– If you didn’t use the shaver for a month or longer, charge it completely before using.

Usage

The best shaving results are achieved if your skin is dry. Your skin may need 2-3 weeks to get used to this shaving system.

• Remove the protective cap (9).

• Switch the shaver on, setting the switch (4) to the «I» position.
  Note: You can switch the shaver on only if the lock button on the switch (4) is pressed.

• Touching the skin slightly, move the shaving block back and forth and rotationally at the same time.

• After shaving switch the shaver off by setting the switch (4) to the «0» position, cover the shaving block (1) with the protection cap (9) and take the shaver away for storage.

• It is recommended to clean the shaving block (1) after every use.

• Press the release button (2) and remove the shaving block (1), clean it both from the inside and outside with the brush (10), clean the blades drive and install the shaving block (1) back to its place (pic. 2, 3, 4, 5). Using of trimmer (pic. 6)
  The trimmer is intended for trimming sideburns and mustache.

• Move the trimmer lock (7) upwards.

• Switch the shaver on, setting the switch (4) to the «I» position.

• Place the trimmer under the right angle to your skin and move it gradually downwards to trim mustache or sideburns.

• Switch the shaver off by setting the switch (4) to the «0» position and close the trimmer by pressing it.]

CLEANING AND CARE

Clean the shaving block (1) after every using or after several operation cycles of the shaver.

• For easy cleaning of the shaving block (1) remove it from the shaver body (pic. 2, 3).
• Using the brush (10) clean the shaving block (1) both from the inside and outside, clean the blades drive (pic. 4, 5).
• Install the shaving block (1) to its place, cover it with the protection cap (9) and take the shaver away for storage.
• It is recommended to clean the shaving heads every two months (pic. 7, 8).
• Switch the shaver off by setting the switch (4) to the «0» position.
• Press the release button (2) and remove the shaving block (1).
• Press and turn the frame clamp counterclockwise and remove the frame.
• Remove every stationary net together with the rotating blade.

Note: Be careful when removing the stationary nets; install the rotating blades to the same stationary nets after cleaning, otherwise fitting of rotating blades to the nets will take some time and this may affect
the quality of shaving.

• Clean the rotating blades and the stationary nets with the brush.

• Install the stationary nets into the shaving block; ensure that nets are fixed; to fix the net turn it clockwise or counterclockwise.

• Insert the rotating blades into the stationary nets.

• Install the locking frame, press the frame clamp and turn it

Note: Match the ledges on the shaving block with the openings in the locking frame; otherwise you’ll not be able to install the locking frame.

• Install the shaving block on the

Attention!

You can wash the shaving block under a warm water jet (pic. 9), if the shaving block (1) is detached from the shaver body (3).

Dry the shaving block (1) thoroughly before installing it, provide that water doesn’t get into the shaver body.

__

Trimmer

• Clean the trimmer after each
• Switch the shaver
• Move the trimmer lock (7)
• Clean the trimmer with the brush (10) supplied with the
• Every six months lubricate the trimmer with a drop of oil for sewing machines or hair

Replacement of shaving heads (pic. 7, 8) For the best shaving results replace the shaving heads every 2 years.

Replacement of shaving heads is per- formed as described in chapter «CLEANING AND CARE».

• Switch the shaver
• Press the release button (2) and remove the shaving block (1).
• Turn the frame clamp counterclockwise and remove the
• Replace the shaving heads, install the locking frame, press the frame clamp and turn it
• Install the shaving block (1) on the

Note: After replacement of the shaving heads the fitting of rotating blades to the nets will take some time.

ENVIRONMENTAL PROTECTION

The shaver is provided with a disposable battery. Before you throw away the inopera- tive shaver discharge the battery complete- ly, remove it and dispose of it according to the hazardous waste disposal regulations of your country.
Do not throw away the shaver until you remove the built-in battery.

DELIVERY SET

Men shaver – 1 pc. Power cord – 1 pc. Protective cap – 1 pc. Cleaning brush – 1 pc.

TECHNICAL SPECIFICATIONS

Supply voltage: 220-240 V ~ 50 Hz Power consumption: less than 1 W
The manufacturer preserves the right to change the specifications of the unit with- out a preliminary notification.
Unit operating life is 3 years

__ Guarantee

Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

This product conforms to the EMC-Requirements as laid down by the Council Directive 2004/108/ЕС and to the Low Voltage Regulation (2006/95/ЕС

Read More About This Manual & Download PDF:

References

• Бытовая техника Vitek - официальный сайт производителя мелкой бытовой техники для дома и ухода за собой Vitek.ru

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>