ATEL V810 4G LTE Cat-4 Home Phone Connect Instruction Manual
- June 4, 2024
- ATEL
Table of Contents
ATEL V810 4G LTE Cat-4 Home Phone Connect
About your V810:
Device Display
-
LCD Display
Displays Home and Device Information display screen. -
Power Button
Power the V810 on/off by pressing and holding this button. You can also short press this button to wake up the screen and toggle screens to check device information -
Battery Port
This battery port is used to connect to the battery holder (3x AA batteries) or a Ni-MH rechargeable battery pack (sold separately). -
Reset Button
Use a pin to push and hold this button for 3 seconds for factory reset. -
SIM Card Slot
Insert your 4FF SIM card into this spring-loaded SIM slot. To remove a SIM, press the edge of the SIM inward and the SIM would pop outward from the SIM slot. -
Type-C Port
Use this port to connect the USB-C cable to a wall adapter for external power. Connect to your computer using a USB-C cable for Online Portal access. -
Phone Port (RJ11)
Insert a telephone cord to this port and plug the other end into your telephone base. -
Antenna Connector
Install an optional antenna (sold separately) to increase signal strength.
Setting up your V810
Install SIM Card
- Remove the V810 back cover.
- Carefully lift the battery holder from the side.
- Install the 4FF Nano SIM card into the spring-loaded SIM slot as the image shows. To remove a SIM, press the edge of the SIM inward and the SIM will pop outward from the SIM slot.
Install Battery
Remove the battery cover. Properly align and install 3 AA batteries into the
battery holder. Put the battery cover back in place as shown in the image.
Alternatively, a Ni-MH rechargeable battery pack (sold separately) can be
connected to the Battery Port.
Note: During a power outage or if the wall charger is unplugged, the V810
continues to run off the batteries to support Voice. During a power outage,
only corded phones that do not require electric power can be used to make or
receive calls (including calls to 911).
Equipment External Power
To connect your V810 to the power outlet, insert your USB cable to the device
USB-C port and plug the other end into a wall adapter.
WARNING! Please only use the provided USB adapter for the V810. The use of other incompatible adapters may cause damage to your device and void the warranty.
Turning your V810 On/Off
To turn on your V810 press and hold the Power button. To turn off your V810 , press and hold the Power button until you see the screen turn of.
Optional Add-On’s: Install an Antenna
To increase signal strength, you can install an optional antenna.
- Align the antenna with the antenna port and screw securely into place (in a clockwise direction).
- Restart the V810 after the antenna is installed.
Note: Antenna sold separately. Using optional accessories (antenna and battery pack) by ATEL are recommended, available at ATEL website, https://www .atel-usa.com/.
LCD Display Icons Overview:
Connect your Telephone to the V810
The V810 provides 2 telephone ports (RJ11). The ports use the same telephone
number.
Plug the telephone cord into one of the telephone ports on the back of the
V810 (the other end of the cord must remain plugged into the back of your home
telephone base unit).
Note: The telephone and telephone cord are not included.
Make Calls
Before making a call, make sure at least one of the signal strength indicator bars ( ) is lit up. If no signal bars are lit, move the V810 to a location that can receive a signal. Pick up the handle of your telephone then dial the number to use call services.
Using a Text Telephone
To use the V810 with TTY, you must first change the TTY mode from the default
(None) to one of the following modes. From the connected telephone dial pad,
dial
“##56*n#” where “n” indicates the TTY mode:
- 0 – None (TTY) is disabled
- 1 – Full TTY Mode
- 2 – VCO mode
- 3 – HCO mode
Online Device Management Portal
You can access your V810 Online Portal to view device status, change your
device settings, and perform manual software upgrades.
- First connect your V810 to a computer with a USB-C cable and then enter http://192.168.0.1 in the browser URL address bar.
- The login username is “admin”. The unique password can be found on the device label (under the battery holder).
Online Device Management Portal
From the HOME menu, you can view your device information and network status.
Go to the ABOUT menu to check for remote software upgrades.
Regulatory Statements
Please review the Regulatory Statements for this device in the device User
Manual, available at www.ATEL-USA.com.
Voice/Emergency calls:
ATEL cannot guarantee the voice or E911 calls availability. Making a
successful call depends on your hardware (telephone) availability, physical
location, wireless signal strength, and/or network services. You should never
rely solely on any wireless mobile device for essential communications
(medical emergencies, for example). Check with your wireless service
providers. When making an emergency call, remember to give all the necessary
information as accurately as possible.
Disclaimer
Certain variations may be present between the device and user manual
description depending on software release or specific network services. ATEL
shall not be held legally responsible for
such deviations, if any, nor for their potential consequences.
Limited Warranty:
The full ATEL USA Warranty Policy can be found at www.atel-usa.com/warranty.
On this page you can “Start a Warranty Claim”, “Check on an Existing Claim”
and read our Warranty Policy by
clicking on “ATEL’s Warranty Policy”. Please follow all warranty instructions
available and if you have any questions contact us at support@atel-
usa.com.
Our Website: www.atel-usa.com
Contactusat: support@atel-usa.com
For Warranty information, see our website under the Support tab.
© 2022 Asiatelco Technologies, Inc. All Rights Reserved PN
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>