VITEK VT-2332 W Humidifier Instruction Manual
- June 3, 2024
- VITEK
Table of Contents
VITEK VT-2332 W Humidifier
HUMIDIFIER VT-2332 W
Insufficient room humidity negatively affects humans’ and pets’ health as well
as plants and furniture. The recommended comfortable room humidity level is
from 40% to 60%.
The humidifier allows you to improve the air qual-ity in the room.
DESCRIPTION
- «Mist» release nozzle with lid
- Carrying handle
- Water level scale
- Water tank
- Water tank lid
- Process chamber with sprayer
- Body
- Colored illumination
- Operation setting button «TIMER»
- Night mode button «LIGHT»
- Display
- Air inlet grid and foam filter
- «Mist» release intensity button «MIST»
- On/off button «POWER»
ATTENTION!
For additional protection it is reasonable to install a residual current
device (RCD) with nominal operation current not exceeding 30 mA. To install
RCD, contact a specialist.
SAFETY MEASURES
Before using the electrical unit, read this instruction manual carefully and keep it for future reference. Use the unit for its intended purpose only, as specified in this manual. Mishandling of the unit may lead to its breakage and cause harm to the user or damage to his/her property.
- Before switching the unit on, make sure that voltage of the mains corresponds to unit oper-ating voltage.
- Place the unit on a flat, moisture-resistant surface. The distance to the walls, other fur-niture and interior objects should be at least 30 cm.
- Do not place the unit on carpet surfaces with high pile.
- Do not place the air humidifier in places exposed to direct sunlight, high temperatures, near computers or other sensitive electronic appliances.
- Do not use the unit outdoors.
- Use the supplied removable parts only.
- Do not operate the unit without water; switch the unit off when the water tank is empty.
- Do not use soda or dirty water or any perfume additives.
- Water temperature should not exceed +40°С.
- Do not switch the unit on if the water tank is not installed.
- Unplug the unit before removing the water tank.
- Do not cover the unit.
- Do not cover the openings on the unit body and avoid getting of foreign objects inside them.
- Do not immerse the unit body, the power plug or the power cord into water or any other liq-uids.
- Do not move or tilt the unit during the opera-tion and do not remove the water tank.
- Always unplug the unit and pour out water from the water tank and the process cham-ber before cleaning or if you do not use the air humidifier.
- Before moving the unit to another place, unplug it and pour out water from the water tank and the process chamber. When carrying the unit, hold it by the body with both hands.
- Do not touch the power plug with wet hands.
- Clean the unit regularly.
- Replace the batteries in time.
- Do not allow children to touch the unit body and the power cord during operation.
- This unit is not intended for usage by chil-dren.
- The unit is not intended for usage by physi-cally or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
- Do not leave children unattended to prevent using the unit as a toy.
- For children safety reasons do not leave poly-ethylene bags, used as packaging, unat-tended.
Attention! Do not allow children to play with polyethylene bags or packaging film.
Danger of suffocation!
- Never pull the power cord when disconnecting the unit from the mains; take the power plug and carefully pull it out of the mains socket.
- Never use the unit if the power cord or the power plug is damaged, if the unit works improperly or after it was dropped.
- Do not attempt to repair the unit. Do not disas-semble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply to any authorized service center from the contact address list given in the warranty certificate and on the website www.vitek.ru.
- Transport the unit in the original package only.
- For environment protection do not discard the unit with usual household waste after its ser-vice life expiration; apply to a specialized cen-ter for further recycling.
- Keep the unit out of reach of children and dis-abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage under cold (winter) conditions, it is necessary to keep it for at least three hours at room tem-perature. There may be water spots in the air humidi-fier, this is normal, as the unit has undergone factory quality control.
- Unpack the unit, remove any stickers and package materials that can prevent unit oper-ation. Check the unit for damages. In case of damages do not switch the unit on.
- Before plugging the unit in make sure that your home mains voltage corresponds to the unit operating voltage.
Notes:
Use the air humidifier at the room temperature from +10° С to +40°С, and
relative humidity less than 80%. Water temperature should not exceed +40°С.
USING THE AIR HUMIDIFIER
- Remove the nozzle (1).
- Take the water tank by the handle (2) and remove it from the unit body (7).
- Turn over the tank (4), remove the lid (5) rotat-ing it counterclockwise.
- Fill the tank (4) with necessary amount of water, insert the lid (5) into the water inlet and turn it clockwise until bumping.
- First place the filled water tank (4) back to its place and then install the nozzle (1).
- Wait till the process chamber (6) is filled with water.
- Insert the power plug into the mains socket.
- Switch the unit on touching the button (14), you will hear a sound signal and the unit will be switched on with the «mist» release intensity 2; the digital indications of relative room air temperature and «mist» release intensity icon will be shown on the display (2), the illumina-tion (8) will light up.
- To switch the air humidifier off touch the but-ton (14) again.
- Unplug the unit.
Notes:
- The operation mode selection and setting buttons are sensory, you just need to touch the button to switch the necessary operation mode on.
- The room air temperature indications may be slightly different from the readings of another thermometer.
- Draughts or other air flows may significantly affect the air temperature indications in the room.
OPERATION MODE CONTROL BUTTONS
ON/OFF button (14)
Touch the button (14) to switch the unit on and touch the button (14) again to
switch the unit off.
«Mist» release intensity button (13)
Consequently touch the button (13) to select the «mist» release intensity, the
«mist» release intensity will be shown on the display with digital symbols
«1-2-3».
- «1» – low intensity,
- «2» – medium intensity,
- «3» – high intensity.
Timer setting button (9)
- Consequently touch the button (9) to set up the timer within the range from 1 to 12 hours (with 1 hour step); the timer operation time will be shown on the display (11).
- When the set time is reached the unit will be switched off.
- To switch the timer off touch the button (9) until the symbol «0» appears on the display (11).
«Night» mode on/off button (10)
- Touch the button (10) to switch the «night» mode on, only the «mist» release intensity icon will be shown on the display (11).
- To switch the «night» mode off touch the button (10) again.
Note : – in the «night» mode the unit will operate at the preset «mist» release intensity and the display (11) illumination will not bother you.
Low water level indication
- When the water tank (4) is empty, the unit will be switched off, there will be sound signals, and the empty water tank icon will be flashing red on the display (11).
- Switch the unit off touching the button (14), remove the nozzle (1) and the water tank (4). Fill the tank (4) with water (see the chapter «Using the air humidifier»). First place the filled water tank (4) on the air humidifier body (7) and then install the nozzle (1).
- Switch the unit on for further operation.
CLEANING AND CARE
WARNING! Always switch the unit off and unplug it before cleaning.
Hard water causes appearance of mineral scale in the process chamber (6) and in the water tank (4) that leads to improper operation of the unit. To avoid it:
- use filtered, boiled and settled water. If tap water is hard, it is recommended to mix tap water with distilled water in proportion 1:1. If tap water is too hard, mix it with distilled water in proportion 1:2 or use distilled water only. Change water in the water tank (4) twice a week.
- Thoroughly wash the process chamber (6) and the water tank (4) with neutral detergent solution twice a week.
- To clean the sprayer add 5-10 drops of detergent on it and wait for approximately 10-15 minutes. Remove the scale from the sprayer surface with a soft brush, and then wash the process chamber (6) with neutral detergent solution.
- Rinse the process chamber (6) and the water tank (4) several times. Wipe the process chamber (6) with a soft cloth.
- Clean the air humidifier body (7) with a soft, slightly damp cloth, and then wipe it dry.
- Remove and clean the air inlet grid (12) and the foam filter as it becomes dirty.
Notes:
- Do not immerse the air humidifier body into water or other liquids.
- Do not use abrasives or solvents for cleaning the «sprayer».
- As a cleaning agent for the «sprayer» you can use a descaling agent for kettles, strictly following the instruction for this substance.
STORAGE
- Pour the water out of the tank and make sure that the process chamber and the «sprayer» are dry before taking the unit away for storage.
- Do not keep the unit with water inside the tank or the process chamber.
- Keep the air humidifier away from children in a dry cool place.
TROUBLESHOOTING
DELIVERY SET
- Air humidifier – 1 pc.
- Instruction manual – 1 pc.
TECHNICAL SPECIFICATIONS
- Supply voltage : 220-240 V ~ 50 Hz
- Power consumption : 23 W
- Water tank capacity : 4 L
- Water flow : 250-300 ml/h
- Humidified area : up to 35 m2
The manufacturer reserves the right to change the unit specifications without a preliminary notification Unit operating life is 3 years
Guarantee
Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee
A production date of the item is indicated in the serial number on the technical data plate. A serial number is an eleven-unit number, with the first four figures indicating the production date. For example, serial number0606ххххххх means that the item was manufactured in June (the sixth month) 2006.