VITEK VTC-TNB4LPRN 4 Inch MegaPixel License Plate User Guide

VITEK VTC-TNB4LPRN 4 Inch MegaPixel License Plate

Specifications

• Model: VTC-TNB4LPRN
• Series: Transcendent Series
• Resolution: 4 MegaPixel
• Feature: License Plate Recognition, WDR, IP Motorized Bullet Camera

Product Usage Instructions

Components and Accessories:
Ensure you have the following components and accessories:

• Hex Wrench
• Weather Resistant Cap
• Network Coupler

Cable Connections:
To connect the camera:

1. Attach the weather-resistant cap to an ethernet patch cable.
2. Connect the camera’s ethernet adaptor.
3. If not using PoE, connect the power cable to an approved 12VDC power supply.

Installation:
Steps for mounting the camera:

1. Ensure the installation surface can support three times the camera’s weight.
2. Use the provided drill template to mark holes for screws and cables.
3. Route and connect cables, secure the mounting base, and adjust the viewing angle.

LAN Configuration:
To access the camera on the local network:

1. Use the IP-Tool or a web browser to access the camera.
2. Install the IP-Tool on a PC connected to the LAN.
3. Modify the camera’s IP address to match the local network segment.

FAQ

• How do I reset the camera to factory settings?
  Press and hold the reset button for over 10 seconds to restore factory settings.

• How do I adjust the viewing angle of the camera?
  Loosen the screws to adjust the viewing angle. Tighten them after adjusting. View the image on a monitor before making adjustments.

• How do I access the camera on the local network?
  You can either use the IP-Tool or access it directly in a web browser. Make sure to modify the camera’s IP address to match your local network segment.

FEATURES

• 1/1.8” 4 MegaPixel Progressive Scan CMOS Sensor
• Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light Producing Color Images in Very Dark & Night Scenes
• Up to 30fps live view @ 4 MegaPixel (2592 × 1520)
•  8~32mm @F1.6 Motorized Varifocal Lens
•  Matrix IR (up to 325’ IR Range)
• True Wide Dynamic Range (120dB)
• True Mechanical Day / Night function by ICR
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Intelligent Analytics: License Plate Recognition, Vehicle Type Detection, Video Exception
• 10,000 Vehicle Plate Database
• 0-75m/h (120km/h) Capture Speed (Dependant on Installation)
• Overlay Options: Time, Location, License Plate Information
• Triple Streaming: H.265+ / H.265 / H.264+ / H.264 / MJPEG
• 1 Ch. Audio In + 1 Ch. Audio Out*
• 1 Ch. Alarm In + 1 Ch. Alarm Out, 1 Ch. CVBS
• Supports Wiegand Protocol for Advanced Access Control Integrations
• Remote Viewing via VMS, Web Browsers, and iOS & Android Apps
• MicroSD Card Slot for Local Recording (256GB)
• IP67 Weather Resistance
• Wall Mount Included, Optional Mounts: Junction Box VT-TJB01 [See Additional Mounting Options on pg. 12]
• 12VDC / 24VAC [Dual Voltage] & PoE (Power over Ethernet) Operation Options [See Power Supply Options on pg. 13]
• 3-Year Warranty

Components and Accessories

Overview

1. Ethernet Connector
2. Audio Input (MIC)
3. Audio Output (HP)
4. CVBS Video Output
5. Alarm Input/Output
6. Wiegand interface
7. RS485
8. Power Connector
9. Reset
10. DC IN&CVBS Interface
11. Zoom-
12. Zoom+
13. Micro SD Card Slot

Cable Connections

First connect the weather resistant cap to an ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power cable to an approved 12VDC power supply.

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.

Connecting Alarm Input / Output

Alarm Input

Alarm Output
Max. Load of Alarm Output: 30VDC, IA

Wiegand Interface:

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill 4 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template.

2. Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws.

3. Loosen the screws to adjust the viewing angle of the camera. After that, tighten the screws. Before adjustment, view the image of the camera on a monitor.

4. Press the T or W button to obtain an optimum image.
5. Finally, re-install the cover.

LAN Configuration

The camera can be accessed on the local network either using the IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Soft-ware/Transcendent-IPTool.zip, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
   For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera should be changed to 192.168.13.X. After modifying, please input the password of the administrator and click “Modify” button to modify the setting.
   ** Default admin password: “123456″.

4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM . IE browser will download the Active X control. After downloading, a login window will pop up as shown below:

Input the user name and password to log in.
Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

• IP address : 192.168.226.201 HTTP: 80
• Subnet Mask : 255.255.255.0 Data Port: 9008
• Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.
   Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download an Active X control.

3. After downloading the Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to System Congfig→Network Config→Port menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify the IP address.

3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.

4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM.

5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.

DETAILED SPECIFICATIONS: VTC-TNB4LRPN

720P (1280 × 720) / D1/CIF (480 × 240)
Min. Illumination| 0.001 lux@F1.6, AGC ON, 0 lux with IR
Lens| 8~32mm Mtrzd Varifocal @F1.6, motorized
FOV| Horizontal: 41°~15.5°, Vertical: 23°~9.5°, Diagonal: 46.5°~18°
Lens Mount| Integrated
Recommended ANPR| 23~99′ (7-30M)
Other Features| BLC, HLC, Defog
WDR| 120dB True WDR
DNR| XD DNR (3D-DNR / 2D-DNR)
S/N Ratio| >50Db
Angle Adjustment| Pan: 0°~360°, Tilt:0°~90°, Rotation: 0°~360°
IR| Matrix (2)
IR Distance| 325′

Video Compression

| Main stream: H.265+ / H.265 / H.264+ / H.264

Sub stream: H.265+ / H.265 / H.264+ / H.264 / MJPEG

Third stream: H.265+ / H.265 / H.264+ / H.264 / MJPEG

Main Stream

|

4MP/2K/3MP/1080P (60Hz :1 ~ 30fps; 50Hz : 1 ~ 25fps) HFR Mode: 1080P/720P (60Hz: 1~60fps; 50Hz: 1~50fps)

Sub Stream| 720P/D1/CIF ( 60Hz:1 ~ 30fps, 50Hz: 1 ~ 25fps )
Third Stream| D1/CIF ( 60Hz:1 ~ 30fps, 50Hz: 1 ~ 25fps )
Bit Rate| 64 Kbps ~ 8 Mbps
Bit Rate Type| VBR / CBR
Audio Compression| G.711A / G.711U

Image Settings

|

ROI, Saturation, Brightness, Hue, Contrast,Wide Dynamic, Sharpness, Image Mirror, Image Flip, Noise Reduction – Image Settings Adjustable through Client Software or Web Browser

ROI| Each ROI to be configured separately
Network| 100M RJ 45
Video Output| CVBS Output (BNC × 1)
Audio| 1CH Audio Input, 1CH Audio Output*
Storage| Built-in microSD Card Slot – up to 256GB, Network Remote Storage
---|---
Reset| YES
Alarm| 1CH Alarm Input, 1CH Alarm Output
RS485| YES
Wiegand| YES – Supports Wiegand Protocol for Advanced Access Control Integrations [In or Out Configurable]
Remote Viewing| VMS / Web Browser / Mobile (iOS/Android)
Supported Browsers| Internet Explorer, Chrome and Firefox with IE Tab, Edge in IE Mode
Online Connection| Support Simultaneous Monitoring for up to 10 Users, Support Multi-stream Real Time Transmission
Interface Protocol| ONVIF

Network Protocol

| DP, IPv4, IPv6, DHCP, NTP, RTSP, RTP, RTMP, RTCP, PPPoE, DDNS, SMTP, FTP, SNMP,HTTP, HTTP POST,802.1x, UPnP, HTTPs, QoS
Smart Alarm| Motion Detection, Sensor Alarm, SD Card Error, SD Card Full, IP Address Conflict, Cable Disconnection
Intelligent Analytics| License Plate Recognition, Vehicle Type Detection, Video Exception Detection
General Functions| Watermark, Video Mask, Oprational Diagnostic [Heartbeat], Corridor Mode

Security

| Video Encryption, Firmware Encryption, HTTPs Encryption, Configuration Encryption, Illegal Login Lock, IP Address Filtering, 802.1x Authentication, Basic and Digest Authentication for HTTP/HTTPs
POE (Standard)| YES (IEEE802.3af)
Ingress Protection| IP67
LPR Snapshot| Overview and Cutout of Plate for Picture
License Plate Database| Whitelist up to 10,000
OSD Features| Snapshot Time, Location, License Plate Information
Capture Speed Range| 0-70m/h (0-120km/h) *Dependant on Installation
Power Supply| DC12V/AC24V/PoE
Power Consumption| <12W
Operating Environment| -22°F~140°F (-30°C ~ 60°C) Humidity: less than 95 % (non-condensing)
Storage Environment| -22°F~149°F (-30°C ~ 65°C) Humidity: less than 95 % (non- condensing)
Dimensions| 10.96” × 3.95” × 3.49” (278.3mm × 100.2mm × 88.7mm)
Weight Net (Shipping)| 2.59lbs / 1176g (3.03lbs / 1376g)
Installation Options| Ceiling Mounting, Wall Mounting
Certificates| CE, FCC

SUGGESTED ACCESSORIES AND RELATED PRODUCTS FOR VTC-TNB4LPRN

• VT-TJB01
  Optional Junction Box

• VT-TPLMT
  Transcendent Universal Pole Mount (reqs. VT-TJB01)

• VT-TCNMT
  Transcendent Universal Corner Mount (reqs. VT-TJB01)

• Power Supplies for VTC-TNB4LRPN
  • VT-12VDC-2000S – Slim Case 12VDC Transformer 2 AMP – UL Listed
  • VT-24VAC/50 – 24VAC Linear Transformer 50VA – UL Listed
  • VT-1205A-D4B – 4 Output 12VDC Power Center w/Optional Backup Battery – 5 AMP – UL Listed
  • VT-1210A-D9B – 9 Output 12VDC Power Center w/Optional Backup Battery – 10 AMP – UL Listed
  • VT-1230A-D18 – 18 Output 12VDC Power Center – 30 AMP – UL Listed
  • VT-2410A-A9 – 9 Output 24VAC Power Center – 10 AMP – UL Listed
  • VT-2415A-A18 – 18 Output 24VAC Power Center – 15 AMP – UL Listed

• PoE Injectors for VTC-TNB4LRPN

  • VT-POE60 – 60 Watt POE Mid-Span Injector, 4-Pair Compliant, IEEE802.3af/at Auto Detect, Distance up to 330’
  • VT-POE95 – 95 Watt POE Mid-Span Injector, 4-Pair Compliant, IEEE802.3af/at Auto Detect, Distance up to 330’

• TRANSCENDENT NVRs!
  A Standalone Solution with Programmable Analytic Support and NDAA Compliance!

  • Up to 12MP Recording
  • H.265S / H.265+ / H.265 / H.264 Video Compression
  • GEN IV Analytic Support Including Face Detection, Target Counting, Heat Map, and More!
  • Available in 4, 8, and 16, 32, 64, and 128 Channels
  • Up to 192TB Depending on Model (12TB per HDD)
  • PoE Support Available (Model Dependent)

• Also Consider Vitek NDAA Compliant Wireless Bridge Products to Reduce Costly Cable Installation!
  VT-WB1150, VT-WB2150, and VT-WB5900 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, High Speed Transmission, and Point-to-Multi- Point (P2MP) Topology

With wireless ranges of 3000ft. (VT-WB1150), 1.25 miles (VTWB2150), and 3 miles (VT-WB5900) these products eliminate the need for expensive and troublesome long-distance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight and durable units are easy to install and easy to use with an innovative and straight forward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with over 100 IP Group Configurations.

LIMITED PRODUCT WARRANTY

• VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
• This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
• The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
• The product must not have been tampered with in any way or the guarantee will be considered null and void.
• This guarantee does not affect your statutory rights.
• Contact your local VITEK Reseller should servicing become necessary.
• VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.

CLASS A DIGITAL DEVICE (INDUSTRIAL & COMMERCIAL ENVIRONMENT)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to CE and FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct

ABOUT COMPANY

• 28492 CONSTELLATION ROAD VALENCIA, CA 91355
• WWW.VITEKCCTV.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>