VITEK VT-8305 VT Iron Instruction Manual

VITEK VT-8305 VT Iron Instruction Manual

IRON VT-8305 VT

A travel iron will help you to take care of your clothes when you travel or have a business trip.

DESCRIPTION

1. Handle
2. Burst of steam button
3. Water inlet lid
4. Water tank
5. Power cord
6. Pase of the iron
7. PUSH button for the handle folding
8. AC voltage selector 110/220V
9. Soleplate
10. Pilot lamp of the heating element
11. Temperature control knob
12. Continuous steam supply on/off handle
13. Beaker

SAFETY MEASURES

Before using the unit, read these instructions carefully and pay attention to illustrations

• A travel iron will help you to take care of your clothes when you travel or have a business trip, but it is not to be considered as a substitute for a normal home iron.
• Before plugging the iron in, set the AC voltage selector according to the mains voltage.
• After using the iron at the mains voltage of 110 V always set the AC voltage selector to the 220 V position, this will prevent the iron from damage if it is connected to the mains with higher voltage.
• Do not connect the iron to mains sockets intended for electric shavers (in long distance trains).
• Use the iron only for the intended purposes specified in the instruction manual.
• Do not use the unit outdoors.
• Before switching the iron on, unwind the power cord completely.
• The power cord is equipped with a «euro plug»; plug itinto the socket with reliable grounding contact.
• Place the iron on a flat stable surface or use the ironing board.
• Never leave the operating iron unattended.
• Always unplug the unit if you are not using it.
• Always take the power plug out of the socket before filling the water tank with water.
• The water inlet lid should be closed during ironing.
• Do not fill the water tank with scented liquids, vinegar, starch solution, descaling reagents, chemicals, etc.
• Avoid contact of open skin areas with iron hot surfaces or outgoing steam to avoid burns.
• Provide that the power cord is not hanging over the edge of the ironing board and make sure that it does not touch hot surfaces.
• Before plugging/unplugging the iron, set the temperature control knob to the «0» position, and the continuous steam supply knob to the position « » (steam supply is off).
• To unplug the iron always hold the power plug, never pull the power cord.
• To avoid electric shock do not immerse the unit into water or any other liquid.
• For children safety reasons do not leave polyethylene bags, used as packaging, unattended.

Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

• Never allow children to use the unit as a toy.
• This unit is not intended for usage by children. Place the unit out of reach of children during the operation and cooling down.
• The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
• Do not use the unit if the power cord or the plug is damaged, if the unit works improperly or after it was dropped or in case of leakage.
• Do not attempt to repair the unit. Do not disassemble the unit by yourself, if any malfunction is detected or after it was dropped, unplug the unit and apply to any authorized service center from the contact addresslist given in the warranty certificate and on the website www.vitek.ru.
• Transport the unit in the original package only.
• Before taking the iron away, unplug it, let the unit cool down completely and pour the remaining water out.
• Keep the unit out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS AND WORK SPACES IS PROHIBITED.

IRONING WITHOUT AN IRONING BOARD

You do not always have an ironing board at hand when  travelling. In such a case it is enough to place a twicefolded terry towel on an even surface. Make sure that the surface is heat and water resistant. Do not use glass or plastic surfaces.

BEFORE THE FIRST USE

After unit transportation or storage under cold (winter) conditions, it is necessary to keep it for at least 3 hours at room temperature before switching on.

• Unpack the iron; remove the protection (if any) fromthe iron soleplate (9).
• Wipe the iron soleplate with a clean dry cloth.
• Before plugging the iron in, set the AC voltage selector (8) according to the mains voltage. After using the iron at the mains voltage of 110 V always set the AC voltage selector (8) to the 220 V position, this will prevent the iron from damage if it is connected to the mains with higher voltage.
• There may be water residue in the tank, this is normal, as the iron has undergone factory quality control.
• During ironing and after it, do not touch the unit surface marked with the symbol . Danger of burns!

FILLING THE WATER TANK

Before filling the tank with water make sure that the unit is unplugged.

• Lift the handle (1) and it will be fixed. To move the handle (1) down, press the PUSH button (7) first.
• Set the temperature control knob (11) to the «0» position and the continuous steam supply handle (12) to the « » position (steam supply is off).
• Open the water inlet lid (3).
• Do not pull on the lid too much, a small effort will be enough.
• Use the beaker (13) to fill the unit with water, then close the lid (3) tight.

Note

• Steam supply is impossible if the water tank is empty.
• If you need to refill water during ironing, switch off and unplug the iron.
• Do not fill the water tank with scented liquids, vinegar, starch solution, descaling reagents, chemicals, etc.
• After you finish ironing, switch the iron off, wait until it cools down completely, then open the water inlet lid (3), turn over the iron and drain the remaining water

IRONING TEMPERATURE

Before operation, test the heated iron on a piece of cloth to be sure that the iron soleplate (9) and the water tank(4) are clean.

• Always check the recommended ironing temperature indicated on the tag before ironing.
• If there is no tag with recommendations for ironing, but you know the type of fabric, use the following table to determine the proper temperature.
  Icons| Fabric type (temperature)
  ---|---
  MIN| Synthetics, nylon, acrylic, polyester (low temperature)
  •| Silk (low temperature)
  ••| Wool (medium temperature)
  •••| Cotton/Linen (high temperature)
• This table is only valid for smooth materials. Fabrics of other types (crimped, raised, etc.) are best ironed at low temperature.
• First sort items by ironing temperature: synthetics to synthetics, wool to wool, cotton to cotton etc.
• The iron heats up faster than it cools down. For this reason, it is recommended to begin ironing at low temperature (for instance, synthetic fabrics).
• After that, start ironing at higher temperature (silk/ wool). Cotton and linen items should be ironed last.
• If an item is made of mixed fabrics, the iron should be set to the lowest temperature (for instance, if an item is made from polyester and cotton, it should be ironed at the temperature used for polyester ironing «MIN»).
• If you cannot define the fabric structure, find a spot that is inconspicuous when the item is being worn and  select the ironing temperature experimentally (always start with the lowest temperature and raise it gradually until you get the desired result).
• Corduroy and other fabrics that become glossy quickly should be ironed strictly in one direction (in the direction of the pile) with slight pressure.
• To avoid appearance of glossy spots on synthetic and silk fabrics, iron them backside.

SETTING THE IRONING TEMPERATURE

• Lift the handle (1) and it will be fixed. Press the PUSH button (7) before moving the handle (1) down.
• Before plugging the iron in, set the AC voltage selector (8) according to the mains voltage. After using the iron at the mains voltage of 110 V always set the AC voltage selector (8) to the 220 V position, this will prevent the iron from damage if it is connected to the mains with higher voltage.
• Unwind the power cord and insert the plug into the socket.
• Turn the temperature control knob (11) to set the required ironing temperature: «MIN», «•», «••», «•••» (depending on the type of fabric), the indicator (10) will light up.
• Place the iron vertically.
• When the iron soleplate temperature (9) reaches the desired temperature value, the indicator (10) will go out, you can start ironing

Note: if the unit is switched on for the first time, the iron heating element burns, so a small amount of smoke or foreign smell may be expected. This is normal.

DRY IRONING

• Set the continuous steam supply on/off handle (12) to the position « »(steam supply is off).
• Turn the temperature control knob (11) to set the required ironing temperature.
• Place the iron vertically.
• When the iron soleplate temperature (9) reaches the desired temperature value, the indicator (10) will go out, you can start ironing.
• After use, unplug the iron and let it cool down completely.
• Press the «PUSH» button (7) and move the handle(1) down.

STEAM IRONING

For steam ironing, set the temperature control knob (11) to the «MAX» position.

• Fill the tank with water as described in the relevant section.
• Insert the power plug into the mains socket.
• Set the temperature control knob (11) to the «•••» position, the pilot lamp (10) will light up.
• Place the iron vertically.
• When the temperature of the iron soleplate (9) reaches the set temperature value, the pilot lamp (10) will go out, you can start ironing.
• Turn on continuous steam supply by setting the handle (12) to the leftmost position « » (steam supply is on) and the steam will start going out from the iron soleplate (9) openings.
• After use, set the temperature control knob (11) to the «0» position, and turn off continuous steam supply by setting the handle (12) to the « » position (steam supply is off).
• Pull the plug out of the socket and let the iron cool down completely.
• Open the lid (3) and pour the water out from the water tank.
• Press the «PUSH» button (7) and move the handle(1) down.

ATTENTION!

If the steam is not constantly supplied during operation, check whether the temperature control knob (11) is set properly, the handle (12) is in the right position and there is water in the water tank (4).

BURST OF STEAM

The burst of steam function is useful for ironing folds and can only be used at high ironing temperatures (when the iron temperature control knob (11) is set to the «•••» position).

When pressing the burst of steam button (2) steam will go out of the iron soleplate more intensively.

Note:

• To avoid water leakage from steam openings, press the burst of steam button (2) with a 10-15 sec. interval.

VERTICAL STEAMING

Vertical steam function can be used only at high ironing temperatures (when the iron temperature control knob (11) is set to the «•••» position). Hold the iron vertically at the distance of 10-15 cm from the clothes, press the burst of steam button (2) with a 10–15 second interval, steam will be heavily supplied from the iron soleplate (9

IMPORTANT INFORMATION

• Vertical steaming is not recommended for synthetic fabrics.
• To avoid fabric melting, do not touch it with the iron soleplate (9) while steaming.
• Never steam clothes on a person as the temperature of the released steam is very high, use a clothes hanger or a coat rack.

CLEANING AND CARE

• Make sure that the unit is unplugged and cooled down.
• Clean the unit body with a slightly damp cloth and then wipe it dry.
• Scale on the iron soleplate can be removed with a cloth soaked in the vinegar-water solution.
• After removing scale, polish the soleplate surface with a dry cloth.
• Do not use abrasives to clean the iron soleplate and body.
• Avoid contact of the iron soleplate with sharp metal objects.

STORAGE

• Set the temperature control knob (11) to the «0» position and the continuous steam supply handle (12) to the « » position (steam supply is off).
• Unplug the unit.
• Put the iron vertically and let it cool down completely.
• Open the water inlet lid (3), turn over the iron and drain any remaining water from the water tank (4).
• Close the lid (3).
• Store the iron vertically in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

1. Iron – 1 pc.
2. Beaker – 1 pc.
3. Instruction manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 100-127V/220-240 V ~ 50/60 Hz
Power consumption: 750-1200 W/900-1100 W

RECYCLING

For environment protection do not throw out the unit and the batteries with usual household waste after its service life expiration; apply to the specialized center for further recycling.

The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.

For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product

The manufacturer preserves the right to change the specifications of the unit without a preliminary notification.

Unit operating life is 3 years

Guarantee

Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee

This product conforms to the EMC Directive 2014/30/EU and to the Low Voltage Directive 2014/35/EU.

A production date of the item is indicated in the serial number on the technical data plate. A serial number is an eleven-unit number, with the first four figures indicating the production date. For example, serial number 0606ххххххх means that the item was manufactured in June (the sixth month) 2006.

References

• Бытовая техника Vitek - официальный сайт производителя мелкой бытовой техники для дома и ухода за собой Vitek.ru

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>