Shenzhen Jonter Digital V19F True Wireless Stereo Earphones User Guide

Shenzhen Jonter Digital V19F True Wireless Stereo Earphones

Product Overview:

• Earbuds*2 pcs(L,R)
• Ear tips*2 pair(S,L)
• Charging Case
• Type C Charging Cable
• User Manual

How To Use

1. .Earphones LED Indicator Ligh
2. Multi‐function Button ( MFB )
3. Charging Point
4. Ear tips
5. Charging Case LED Indicator Light
6. Charging Case LED Indicator Light

Power On/Off

Open the charging case and take out the earphones, the earphones will be automatically power on. When the earphones is power on, put the earphones into the charging case and close the charging case, the earphones can be power off and charging.

Pairing

Open the charging case and take out the earphones,the L/R earphones will enter pairing mode automatically. Then wait a few seconds, the L/R earphones will connect with each other automatically, at the same time, wearing the earphones, you can hear the voice prompt of “pairing”,then open the Bluetooth function on the phone, search device name “V19F” for connection, if connected successful you will hear voice prompt of “connected”.

Volume Control

• Triple-click MFB (L) to turn volume down.
• Triple click MFB (R) to turn volume up.

Play Music

• Play/Pause Music: Short press MFB (L/R) once to play/ pause music.

• Previous Track: Doubleclick MFB(L) turn to the previous song

• Next Track: Double click MFB(R) turn to the next song

• Note: Single earphone mode can’t control volume and songs

Calling

• Answer a call: Short press MFB (L/R)
• Hang up a call: Long press MFB(L/R) for 2s during a call
• Reject a Call: Long press MFB(L/R) for 2s

Activate voice assistant

Long press MFB( L/R ) for 2s to activate Siri or Google assistant, double click MFB( L/R ) will close voice assistant

Resetting The Device

Please follow the below steps in case the earbuds don‘t auto pair

• Step 1: Remove “PLX5” from the list of paired devices
• Step 2: L/R earphones in the charging case and in charging mode, long press L/R MFB for 5s will
• clear the device pairing record and there & white LED will quick flash 3 times
• Step 3: Take out both earbuds from the case, they will now auto pair with each other

LED Indicator Guide

TWS During Pairing Status

| Red and white lights

willflashing alternate

| ****

“Pairing”

TWS Pairing Successful

| Red and white lights will slow

flashing alternate

| ****

“Pairing”

Connected With Device| N/A| “Connected”

Earphone Battery Low

| The red LED flash twice on

every 30 seconds

| ****

“Battery Low”

Earphone Charging

| Red LED will bright all the time

when the earphones is charging

| ****

N/A

Earphone Fully Charged| Red LED will lighting‐off| N/A

Attention Please

Fully charge before use.
Do not press any key for pairing. earphones will go to pairing mode automatically after took out.

Put the earphones in CORRECT POSITION for charging.

•  If the battery is not replaced properly, there will be an explosion risk. The battery can only be replaced with the same type or equivalent type of battery. It is not recommended to replace the battery without permission but can be returned to the manufacturer for replacement.
•  Batteries [battery packs or combination batteries] shall not be exposed to such conditions as lighting, baking, or similar overheating.

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation.

RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Storage & Maintenance

When not using the earbuds, it is recommended that they are stored away in the charging case and placed in a safe, dry location, away from sources of water, light, heat, and dust. They are best stored in an airtight box or bag (not included ).
If the earbuds or case is dirty, wipe it down with a clean microfiber cloth. Do not clean withwater or any sort of cleaning liquid or detergent.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>