Sevylor ‎2000014066 SUP and Water Sport Electric Pump

Safety Instruction

• Not a life-saving device.
• Not for use by children without adult supervision.
• Always wear an approved Personal Flotation Device (Life Preserver).
• Do not overload.
• Never tow from another boat or vehicle.
• Use only in water away from debris and obstructions.
• Do not use in high wind, strong currents, open water or dangerous tides.
• Be familiar with the area you intend to use the boat.
• Never allow diving into or from these boats.
• Never leave in or near water when not in use.
• Know and follow local water safety rules and boating regulations.
• Use only in protected waters.
• Do not use this product under the influence of alcohol or drugs.
• Do not overinflate.
• Follow the inflation sequence on the product.

IMPORTANT INFORMATION

The warnings below relate to various situations. Please observe them.
CAUTION! Denotes an imminent hazard that will result in severe injury if you do not comply with the instructions.
WARNING! Reminds you of safety measures that must be observed. Also denotes unsafe practices which could result in personal injury or damage to the product or property, if you do not comply with the instructions.
CAUTION! It is the owner’s responsibility to make sure all users carefully read and follow the instructions for the safe operation of this product. Observe all local and national laws. Always wear a Personal Flotation Device approved by the proper authorities. Please carefully observe the Capacity Plate information which is printed on the product.
WARNING! These boats are not meant for towing because the extreme pressure of the water while towing can tear the eyelets and/or handles. These boats are not meant to be used in whitewater.
CAUTION! Altering the construction of these boats could jeopardize the safety of the occupants and will void the limited warranty.
CAUTION! Keep the boat away from gasoline, battery acid, solvents, etc., as they can damage the boat. These boats are made of the highest quality materials and comply with NMMA (National Marine Manufacturers Association) regulations.

INFLATION INSTRUCTIONS

CAUTION! Do not overinflate. Pressurize the product to “Inflation Pressure” stated in the chart for your specific product.
WARNING! Never use a compressor, CO2 or compressed air to inflate the boat. Do not let your boat come into contact with sharp, pointed objects.

To inflate using any Sevylor® QuickPump™ unit:

• To begin inflation, open the external stopper and pull to extend out.

• When fully inflated, seal the valve by pushing in the pump nozzle to maintain a seal. Gently back pump out of the valve.

• Attach adapter hose to inflation end of QuickPump™ unit. Insert the hose and turn it on.

• Fully remove the adapter and close the external stopper. The valve should appear depressed in itself.

To inflate using the Sevylor® Dual Action Hand Pump or another inflation device:

• To begin inflation, open external stopper and pull to extend out.

• To close the valve: Push in with the inflation device until the stopper has been depressed, sealing the internal stopper.

• Insert the nozzle of the inflation device into the extended valve and turn on or begin pumping.

• Fully remove the adapter and close the external stopper. The valve should appear depressed in itself.

IMPORTANT! Inflate the boat chambers in the following order:

1. Inflate the inside all-around safety chamber.
2. Inflate the floor chamber(s).
3. Inflate the bottom tunnel chambers. (These tubular chambers are only found on Super Caravelle and Fish Hunter™ models.)
4. Inflate the bustling chamber. (This support chamber positioned at the stern is found only on the large Super Caravelle models.)
5. Inflate the outside main chamber.

The chambers on the boat will be numbered to indicate the order of inflation also. This order of inflation will ensure the proper volume and buoyancy of the safety chamber.
Note: To inflate the mini double lock valve, which is used on some of the Sevylor boat floors and seat bottoms, follow the same inflation instructions above, using the mini double lock valve adapter. The mini Double Lock™ valve adapter is included with all Sevylor® pumps. The adapter can be purchased from Customer Service by calling 1-800-835-3278 (Part Number 5010000707).

CAUTION!

Water temperature and weather do affect the pressure in inflatable products. In cold weather, your product will lose some pressure due to the fact the air will contract. If this occurs, you may want to add a little air to improve the performance of your product. However, in hot weather, the air will expand. You must let some air out to prevent your product from failing due to overpressure. You should avoid exposing your product to extreme temperatures (hot or cold).

DEFLATION INSTRUCTIONS

Deflation instructions using any Sevylor® QuickPump™ unit:

Remove the adapter hose from the inflation end and attach to the opposite deflation end of the pump. Repeat the same steps as inflation. This will draw the air out quickly.

Deflation instructions using the Sevylor® Dual Action Hand Pump:

Remove the adapter hose from the inflation port and attach to the deflation port on the pump handle. Repeat the same steps as inflation. This will draw the air out quickly.

Your boat is NMMA certified using the ABYC standard.

WARNING!

Do not exceed the certified maximum capacities under any circumstances!

NMMA (ABYC

Standard)

| Persons Capacity| Maximum Pay- load Capacity| Engine| Inflation Pressure| Inflation Pressure
---|---|---|---|---|---

Model #

|

Persons Only

| Persons, Gear,

Motor

(if applicable)

|

Max. HP Engine

| Main Chamber(s)| Floor Chamber(s)

HUI 100

| 1 Pers. or 190 lbs.|

190 lbs.

|

N/A

|

0.4 PSI

|

0.4 PSI

HUI 200

| 2 Pers. or 370 lbs.|

370 lbs.

|

N/A

|

0.4 PSI

|

0.4 PSI

HUI 400

| 4 Pers. or 650 lbs.|

650 lbs.

|

N/A

|

0.4 PSI

|

0.4 PSI

WARNING!

Do not exceed the certified maximum capacities under any circumstances!

NMMA (ABYC

Standard)

| Persons Capacity| Maximum Pay- load Capacity| Engine| Inflation Pressure| Inflation Pressure
---|---|---|---|---|---

Model #

|

Persons Only

| Persons, Gear,

Motor

(if applicable)

|

Max. HP Engine

| Main Chamber(s)| Floor Chamber(s)
Colossus™ 2 Person Boat| 2 Pers. or

435 lbs.

|

435 lbs.

|

N/A

|

0.5 PSI

|

0.5 PSI

Colossus™ 3 Person Boat| 3 Pers. or

680 lbs.

|

680 lbs.

|

N/A

|

0.5 PSI

|

0.5 PSI

Colossus™ 4 Person Boat| 4 Pers. or

840 lbs.

|

840 lbs.

|

N/A

|

0.5 PSI

|

0.5 PSI

WARNING!

Do not exceed the certified maximum capacities under any circumstances!

NMMA (ABYC

Standard)

| Persons Capacity| Maximum Pay- load Capacity| Engine| Inflation Pressure| Inflation Pressure
---|---|---|---|---|---

Model #

|

Persons Only

| Persons, Gear,

Motor

(if applicable)

|

Max. HP Engine

| Main Chamber(s)| Floor Chamber(s)
Caravelle

2 Person Boat

| 2 Pers. or

300 lbs.

|

360 lbs.

|

N/A

|

0.9 PSI

|

0.9 PSI

Caravelle

3 Person Boat

| 3 Pers. or

550 lbs.

|

600 lbs.

| 12V Electric Motor (Sevylor 2000004144)|

0.9 PSI

|

0.9 PSI

Caravelle

4 Person Boat

| 4 Pers. or

600 lbs.

|

700 lbs.

|

3.0 *

|

0.9 PSI

|

0.9 PSI

Caravelle

5 Person Boat

| 5 Pers. or

800 lbs.

|

900 lbs.

|

3.0 *

|

0.9 PSI

|

0.9 PSI

• Requires 2000004146 Motor Mount Kit (sold separately) for motors other than Sevylor 12 Volt Motor, Model 2000004144

WARNING!

Do not exceed the certified maximum capacities under any circumstances!

NMMA (ABYC

Standard)

| Persons Capacity| Maximum Pay- load Capacity| Engine| Inflation Pressure| Inflation Pressure
---|---|---|---|---|---

Model #

|

Persons Only

| Persons, Gear,

Motor

(if applicable)

|

Max. HP Engine

| Main Chamber(s)| Floor Chamber(s)
Fish Hunter™ 3 Person Boat| 3 Pers. or

450 lbs.

|

600 lbs.

|

2.0 *

|

0.9 PSI

|

0.9 PSI

Fish Hunter™ 4 Person Boat| 4 Pers. or

650 lbs.

|

700 lbs.

|

4.0 *

|

0.9 PSI

|

0.9 PSI

Fish Hunter™ 6 Person Boat| 6 Pers. or

900 lbs.

|

1200 lbs.

|

3.0 *

|

0.9 PSI

|

0.9 PSI

Fish Master™ 4 Person Boat| 4 Pers. or

800 lbs.

|

900 lbs.

|

3.0 *

|

1.5 PSI

|

N / A

• Requires 2000004146 Motor Mount Kit (sold separately) for motors other than Sevylor 12 Volt Motor, Model 2000004144

WARNING!

Do not exceed the certified maximum capacities under any circumstances!

NMMA (ABYC

Standard)

| Persons Capacity| Maximum Pay- load Capacity| Engine| Inflation Pressure| Inflation Pressure
---|---|---|---|---|---

Model #

|

Persons Only

| Persons, Gear,

Motor

(if applicable)

|

Max. HP Engine

| Main Chamber(s)| Floor Chamber(s)
Super Caravelle 2 Person Boat| 2 Pers. or

300 lbs.

|

360 lbs.

| 12V Electric Motor (Sevylor 2000004144)|

0.9 PSI

|

0.9 PSI

Super Caravelle 3 Person Boat| 3 Pers. or

550 lbs.

|

600 lbs.

|

2.0 *

|

0.9 PSI

|

0.9 PSI

Super Caravelle 4 Person Boat| 4 Pers. or

600 lbs.

|

700 lbs.

|

3.5 *

|

0.9 PSI

|

0.9 PSI

Super Caravelle 6 Person Boat| 6 Pers. or

900 lbs.

|

1,100 lbs.

|

3.5 *

|

0.9 PSI

|

0.9 PSI

• Requires 2000004146 Motor Mount Kit (sold separately) for motors other than Sevylor 12 Volt Motor, Model 2000004144

WARNING!

Do not attempt to mount a motor on any boat that does not state a Max. HP Engine rating.

SEVYTEST™ GAUGE

Some of the Sevylor® products are equipped with a Sevytest™ gauge. The Sevytest™ device is a pressure gauge, not an inflation gauge. The Sevytest™ gauge is found on the side wall, inside the main chamber(s). The purpose is to show you when to let some air out after the pressure has increased due to temperature change. The principle of the Sevytest™ gauge is based on the lengthening of the PVC under the influence of pressure. Once the boat is properly inflated, note the position of the Sevytest™ indicator. Then periodically check the Sevytest™ gauge and let out enough air to keep the test strip in the same general area. If the Sevytest™ indicator is in the “+” zone, add pressure to the product. If the Sevytest™ indicator is in “-” zone, release pressure from the product.

OPERATING INSTRUCTIONS

• Follow all local boating regulations and navigation rules. Familiarize yourself with boating conditions where you plan to use the boat. Use common sense and caution when operating in unfamiliar places.
• Observe the maximum weight the boat can carry and do not overload past this limit. Over-loading jeopardizes the safety of the occupants.
• Be sure all accessories and/or equipment (e.g. oars, life jackets) are in proper working condition before using the boat. Each person occupying the boat is to wear an approved Personal Flotation Device (life preserver).
• Sharp objects are not to be carried in the boat without adequate protection or storage.
• When navigating the boat in any water depth, watch for submerged or sharp objects that may damage or pierce the boat’s air chambers.
• Enter the boat from the port (left) or starboard (right) sides – not from the fore (front) or aft (back) sides.
• Never tow with a boat or any other vehicle.

MOTOR MOUNTING

WARNING!

Do not mount a motor on any boat that exceeds the Maximum Horsepower Rating for your specific boat model. All Sevylor® boats that have a Horsepower Rating can accept the Sevylor® 12V Trolling Motor, Model 2000004144 without purchasing any additional mounting hardware. Refer to 12V Trolling Motor mounting instructions.
Mounting any motor other than the Sevylor® 12V Trolling Motor, Model 2000004144, requires the Sevylor® Motor Mount Kit, Model 2000004146, which is sold separately.

CARE & STORAGE

• These boats are made of the highest quality materials and comply with NMMA (National Marine Manufacturers Association) regulations. Altering the construction of these boats will void the limited warranty and could jeopardize the safety of the occupants.
• If your boat has been used in salt water, rinse it off with fresh water as soon as possible.
• Remove tar spots or other soiled areas by using mild soap and rinsing with fresh water.
• Be sure your boat is completely dry before storing.
• The boats may be stored inflated, but do not place any heavy or sharp objects on it. Storage is best in a dry room.

Caravelle Models

Super Caravelle Models

Colossus™ Models

Fish Hunter™ Models

HUI Models

GRAB LINE INSTALLATION

IMPORTANT: To properly install the inflatable boat’s grab line, first inflate the boat. Feed the grab line through the eyelets on each of the rope holders. Then tie the two loose ends in a square knot at the rear of the boat.

OAR ASSEMBLY: (for models with oar included)

Join the two shafts together by screwing them together into the coupler. Attach the blade to the shafts by screwing in into the bottom of the shaft. Replacement Part #2000004151

The assembled oar is to be inserted into the oar locks from the outside of the boat. The oar retainer ring is then placed onto the top half of the assembled oar, from the inside of the boat, to prevent the oar from sliding into the water (see below).

REPAIRING SMALL PUNCTURES

For inadvertent punctures, you can repair them with the included Sevylor® repair patch.

INSTRUCTIONS:

1. Thoroughly clean and dry the damaged area. Completely deflate if an inflatable article.
2. Cut a portion of the patch to cover the puncture, and allow an additional ¼” on all sides. Always cut a round or oval patch. Never leave corners.
3. Be sure the spot is completely dry.
4. Peel the backing from the patch.
5. Adhere the patch to the puncture.
6. Using your thumb or finger apply even pressure across the entire surface of the patch.

The Sevylor® AirSeal repair kit is also another repair option available (Model

2000003730 – not included). Sevylor® AirSeal is a fast, reliable repair for

vinyl inflatables: air mattresses, toys, pools, and boats as well as rainwear, groundsheets, golf bags, etc.

INSTRUCTIONS:

1. Thoroughly clean and dry the damaged area. Completely deflate if an inflatable article.
2. When the damage is small (a pinhole or tear under 2 inches) apply a light coat of AirSeal two or three times. Allow five minutes to dry between each application.
3. For heavier material, e.g. fabric backed vinyl or a vinyl boat, apply up to five coats allowing a five-minute drying period between coats.
4. Ensure the AirSeal is completely dry before resuming the use of the article.
5. When the damage is more extensive, cut a patch (with rounded corners) using any vinyl material. Generously coat the damaged area spreading the AirSeal at least 3/8” from the torn edges. Apply the patch and apply AirSeal to all edges of the patch making a seal between the patch and the item being repaired. Allow the article to dry for at least 10 hours before using.
   Contains sufficient material for several small repairs.

AirSeal is intended for use with 100% PVC (polyvinyl chloride) only.

Do not use any other material.

You may purchase the Sevylor® repair patch (Model # 2000003731) and Sevylor® AirSeal (Model # 2000003730) by calling Coleman Customer Service at 1-800-835-3278 or going to www.sevylor.com.

INFLATABLE BOATS

3600 North Hydraulic • Wichita, KS 67219 U.S.A. 1-800-835-3278 • www.Sevylor.com

Limited 90-Day Warranty

The Coleman Company, Inc. (“Coleman”) warrants that for a period of 90 days from the date of original retail purchase, this product will be free from defects in material and workmanship. Coleman, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, a replacement may be made with a similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of the initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. Coleman dealers, service centers, or retail stores selling Sevylor® products do not have the right to alter, modify or in any way change the terms and conditions of this warranty.

What This Warranty Does Not Cover

This warranty does not cover normal wear of parts, parts that are not genuine Coleman® parts, or damage resulting from any of the following: negligent use or misuse of the product; commercial use of the product; use contrary to the operating instructions; disassembly, repair or alteration by anyone other than Coleman or an authorized service center. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes. Warranty void if damage to the product results from the use of a part other than a genuine Sevylor® part.
COLEMAN SHALL NOT BE LIABLE FOR DEFECTS THAT ARE CAUSED BY THE USE OF UNAUTHORIZED PARTS OR SERVICE. COLEMAN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THE ABOVE WARRANTY OR CONDITIONS. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
How to Obtain Warranty Service
Take the product to an authorized Coleman service center. You can find the nearest authorized Coleman service center by visiting www.coleman.com or calling 1-800-835-3278 or TDD 1-316-832-8707. If a service center is not conveniently located, attach to the product a tag that includes your name, address, daytime telephone number and description of the problem. Include a copy of the original sales receipt. Carefully package the product and send either by courier or insured mail with shipping and insurance prepaid to: The Coleman Company, Inc. 3600 North Hydraulic Wichita, KS 67219
The costs of transporting the product to Coleman or an authorized service center for warranty service is the responsibility of the purchaser.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. If you have any questions regarding this warranty please call 1-800-835-3278 or TDD 1-316-832-8707.

FAQs

Do I need a pump to inflate the boat?****

Yes, you will need a pump to inflate the boat.

How do I know when it is inflated?****

The boat will be fully inflated when there is no more air coming out of the valve.

How do I deflate the boat?****

You can deflate the boat by pressing down on the valve while you roll up the boat.

How do I roll up the boat?****

When you are done using the boat, you can roll it up by following these steps.
1.     Take out all of the air from inside of the boat.
2.     Roll it from one end to another and then roll it up tightly.
3.     Tie a knot at one end and then secure it with a rubber band or string.
4.     Repeat this step for other end of the boat and then store it in a dry place that is away from direct sunlight and moisture.

How long does it take to inflate a SUP with an electric pump?****

The kind of pump you use will determine how long it takes to inflate your SUP. It will take anywhere between 6 and 10 minutes to use a standard hand pump, depending on how quickly you pump. Depending on the size of the board, it will take 6–8 minutes with a reliable SUP electric pump.

Can you use an electric pump on a SUP?****

The most popular electric pump designs for inflatable SUPs include those that plug into your car battery. pumps that are connected to a battery pack outside. pumps that are connected via a built-in rechargeable battery

How do I choose a SUP electric pump?****

Your SUP should be inflated to the recommended pressure of 13-17 psi using an electric paddle board pump, which can accomplish this task in about five minutes. To have more options while travelling, it is best to choose an electric pump that can be powered by a battery, an outlet, or a cigarette lighter in a car.

Do you need an electric pump for SUP?****

The ability to save time and energy is the main benefit of employing an electric pump. If you frequently use your inflatable SUP board, using the manual pump will take more time and effort than using an electric pump. Your SUP will be inflated in a matter of minutes thanks to the electric pump.

Why is my SUP pump not working?****

If a sump pump won’t operate, there may be a power issue, a jammed float switch or impeller, a damaged part, or the pump itself needs to be replaced. Verify that the device is powered. By using the main electrical panel in the house, verify that it is plugged in and that the circuit is powered.

Can you use air compressor for SUP?****

You may quickly inflate your SUP with a compressor while still getting it to the necessary rigidity for performance.

Video

Download PDF Link;Sevylor SUP and Water Sport Electric Pump pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>