VITEK VT-EPH-HDA5 12 Megapixel Network Indoor Mini Board Camera Instruction Manual

VITEK VT-EPH-HDA5 12 Megapixel Network Indoor Mini Board Camera

Specifications :

• Model: VT-EPH-HDA5
• Camera Type: Covert Pinhole Camera
• Resolution: 2.0 MegaPixel
• Video Encoder Resolution: 5.0 MegaPixel
• Features: Alarm Interface, 2-Way Audio In/Out, Intelligent Analytics

Product Usage Instructions

Installation:
Camera Installation:

1. Secure bracket to the wall with the provided screw.
2. Route and connect the cables.
3. Fasten the camera to the bracket with screws.
4. Adjust the viewing angle before tightening.
5. Firmly tighten screws to finish installation.

Encoder Server Installation:

1. Drill screw holes into the wall according to the template.
2. Insert two screw anchors.
3. Secure bracket to the wall with two screws.
4. Install bracket on the device with two screws.
5. Hook the device onto the bracket until it locks with a click.

Connection:
Connect the camera and encoder to LAN/WAN/PoE for network access. Use the provided LAN configuration for proper setup.

Accessing the Camera:
The camera can be accessed on the local network using the IP-Tool or directly through a web browser.

Accessing via IP-Tool:

1. Ensure camera and PC are connected to LAN.
2. Download and install IP-Tool from the provided link.
3. Modify camera’s IP address to match the local network segment.
4. Use default admin password (123456) for modifications.
5. Double-click IP address to open in web browser, input username and password to log in.

Direct Access via Web Browser:
Manually set PC’s IP address to match camera’s default settings. Open a web browser and enter camera’s IP address to log in using default credentials.

FAQ:

• Q: Where can I find the complete user guide and software updates?
  A: The user guide, software, tools, and updates are available online at http://www.vitekcctv.com/Downloads or by scanning the QR code provided.

Transcendent 2.0 MegaPixel Covert Pinhole Camera with 5.0MP Video Encoder Server

FEATURES

• inhole 2.8mm Fixed Iris Lens Camera
• 1/2.8” 2.0 MegaPixel Progressive Scan CMOS Image Sensor
• p to 30fps @ 2MP (1920 × 1080)
• Included IP Video Encoder Server supports up to 5.0 MegaPixel Cameras!
• H.265+ / H.265 / H.264+ / H.264 / MJPEG encoding
• GEN IV Advanced Analytics: Intrusion Detection, Line Crossing, Target Counting [All by Human / Motor Vehicle Classification], Face Detection, Scene Change, Video Blur,
• Abnormal Color Detection, Heat Map
• Audio: 1 Channel Input, 1 Channel Output*
• Alarm Interface (8-ch In/4-ch Out)
• MicroSD Card Slot (256GB)
• 12VDC + PoE Operation
• 3-Year Warranty

Please research local, state and federal laws regarding the implementation of audio surveillance.

PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads

Components and Accessories

Overview

Installation (Camera)

1. Secure bracket to the wall with the screw provided.

2. Route and connect the cables.

3. Fasten the camera to bracket with screws as shown below.
   Adjust the viewing angle of the camera before tightening.

4. Firmly tighten screws to  finish installation.

Installation (Encoder Server)

1. Drill screw holes into the wall according to the template.
2. Insert two screw anchors.
3. Secure bracket to the wall with two screws.
4. Install bracket on the device with two scews as shown here.
5. Hook the device onto bracket. It will lock when a click is heard.

Connection

LAN Configuration

The camera can be accessed on the local network either using the IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Soft-ware/Transcendent-IPTool_v2.0.2.zip  then install on the PC. Open the installed application.
3.  Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
   • For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click “Modify” button to modify the setting.
   • Default admin password: “123456″.
4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM. The browser will download the Active X control. After downloading the Active X control, a login window will pop up as shown below:

Input the user name and password to log in.

• Default user name: admin / Default password: 123456.
• Directly Access Through a Web Browser
• The default network settings are as shown below:
• IP address: 192.168.226.201 HTTP: 80
• Subnet Mask: 255.255.255.0 Data Port: 9008
• Gateway: 192.168.226.1
• You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.
   Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

2.  Open the Browser and input the default address of IP-CAM and confirm. The browser will download the Active X control.

3.  After downloading the Active X control, a login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. 1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and au to Svstem Confirms → Network Confirm → Port  menu to set up the port number.
2.  Enter System Config → Network Config → IP Address menu to modify the 1D address
3.  Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.
4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM.
5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.

DETAILED SPECIFICATIONS VT-EPH-HDA5

59°, Diagonal FoV: Approx.117°
Min. Illumination| 0.05lux @ F2.2, AGC ON
WDR| 120Db (Camera)
Other Features| BLC, HLC, De-Fog
DNR| 2D/3D NR
DORI| Detect: 125ft (38m), Observe: 49ft (15m), Recognize: 26ft (8m), Identify 13ft (4m)
Video Compression| H.265+ / H.265 / H.264+ / H.264 / MJPEG
H.264 Compression Std.| Baseline Profile / Main Profile / High Profile
Bit Rate (Type)| 64Kbps ~ 6Mbps (VBR/CBR)
Resolution| 1080P(1920×1080), 720P(1280×720), D1, CIF, 480×240
Main Stream| 60Hz: 1080P/720P/D1 (1~30fps), 50Hz: 1080P/720P/D1 (1~25fps)
Sub Stream| 60Hz: 720P/D1/CIF (1~30fps), 50Hz: 720P/D1/CIF (1~25fps)
Third Stream| 60Hz: D1/CIF/480×240 (1~30fps), 50Hz: D1/CIF/480×240 (1~25fps)
Image Setting| Saturation, Hue, Brightness, Contrast, WDR, Sharpness, NR, Image Mirror / Flip, Adjustable Through Client or Web Browser
Audio Compression| G711A/U
Network| 100M RJ45
Audio| 1 CH 3.5mm Audio Input, 1CH 3.5mm Audio Output*
Two-Way Audio| YES
Video| 1CH BNC Video Input Connector
Storage| 1 MicroSD Card Slot, up to 256G
Alarm| 8CH Alarm Input, 4CH Alarm Output
Remote Monitoring| Web browser / Vitek VMS / NVR / Mobile APP
Online Connection| Supports Simultaneous Monitoring of up to 8 Users, Supports Multi-stream Real Time Transmission
Network Protocol| UDP, IPv4/6, DHCP, NTP, RTSP/MP, PPPoE, DDNS, SMTP, FTP, SNMP, 802.1x, UPnP, HTTPS, HTTP POST, Qos
Interface Protocol| ONVIF
Smart Alarm| SD Card Full, SD Card Error, IP Address Conflict, Cable Disconnection, Sensor Alarm, Motion Alarm
Intelligent Analytics| Intrusion Detection, Line Crossing, Target Counting [All by Human / Motor Vehicle Classification], Face Detection, Scene Change, Video Blur, Abnormal Color Detection, Heat Map
General Function| Watermark, IP Address Filtering, Video Mask, Heartbeat, Illegal Login, Corridor Pattern
PoE| Yes, IEEE802.3af
Power| DC12V/PoE
Power Consumption| < 5.5W
Environmental Protection| RoHS 2.0, REACH, WEEE, Directive 94/62/EC
Environmental Conditions| Working: -22° ~140°F (-30°~60°C) / < 95% Humidity, Storage: -22° ~149°F (-30°~65°C) / < 95% Humidity
Dims Camera D × W × H Server L × W × H|

• Camera: 1.97” × 1.24 × 1.97” (31.6 × 30.4 × 31.6mm)
• Server: 4.27” × 3.46 × 1.10” (108.3 × 87.8 × 28mm)

Weight| Camera: 1.8oz (52.4g), Server: 9.57oz (271.4g), TOTAL COMBINED Weight: 11.37oz (322.3g)

Please research local, state and federal laws regarding the implementation of audio surveillance.

DIMENSIONS

OPTIONAL ACCESSORIES AND RELATED PRODUCTS FOR NDAA COMPLIANT TRANSCENDENT IP CAMERAS

TTRRAANSCENDENNSCENDENTT N NVVRRss!! A Standalone Solution with GEN. IV Advanced Analytic Support and NDAA Compliance!

• 8MP (4K) HDMI Output
• H.265S / H.265+ / H.265 / H.264 Video Compression
• GEN IV Analytic Support Including Face Detection, Target Counting, Heat Map, and More!
• Available in 8, 16, 32, 64, and 128 Channels
• Up to 192TB Depending on Model (12TB per HDD)
• PoE Support Available (Model Dependent)

• Also Consider Vitek NDAA Compliant Wireless
• Bridge Products to Reduce Costly Cable Installation!
• VT-WB1150, VT-WB2150, and VT-WB5900 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, High Speed Transmission, and Point-to-Multi-Point (P2MP) Topology

• With wireless ranges of 3000ft. (VT-WB1150), 1.25 miles
• (VT-WB2150), and 3 miles (VT-WB5900) these products eliminate the need for expensive and troublesome long-distance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight and durable units are easy to install and easy to use with an innovative and straight forward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with over 100 IP Group Configurations.

LIMITED PRODUCT WARRANTY

• VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
• The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
• The product must not have been tampered with in any way or the guarantee will be considered null and void.
• This guarantee does not affect your statutory rights.
• Contact your local VITEK Reseller should servicing become necessary.
• VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.

28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.COM
Version 1.0 Jan 2024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>