TELTONIKA OTD140 4G Outdoor Router User Guide
- June 17, 2024
- teltonika
Table of Contents
OTD140
DATASHEET // OTD140
HARDWARE
FRONT VIEW
- Mobile connection strength LEDs
- SIM1/SIM2 slots
- Reset button
- Mobile connection type LEDs
- Mounting Bracket
- ETH ports
- ETH status LEDs
RJ45 LED MEANING
- Orange LED on: link established 10/100 Mbps
Orange LED blinking: active connection
FEATURES
MOBILE
Mobile module| 4G (LTE) – LTE Cat 4 150 Mbps DL, 50 Mbps UL; 3G – 21 Mbps DL,
5.76 Mbps UL; 2G – 236.8 kbps DL, 236.8 kbps UL
---|---
SIM switch| 2 SIM cards, auto-switch cases: weak signal, data limit, SMS
limit, roaming, no network, network denied, data connection fail, SIM idle
protection
Status| Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes
sent/received, connected band, IMSI, ICCID
SMS| SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to
SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP
USSD| Supports sending and reading Unstructured Supplementary Service Data
messages
Black/White list| Operator black/white list
Band management| Band lock, Used band status display
APN| Auto APN
Bridge| Direct connection (bridge) between mobile ISP and device on LAN
Passthrough| Router assigns its mobile WAN IP address to another device on LAN
ETHERNET
LAN| 2 x ETH ports (can be configured as WAN), 10/100 Mbps, compliance with
IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover
---|---
POE IN
| PoE ports | 1 x PoE In |
|---|---|
| PoE standards | 802.3af/at |
POE OUT
| PoE ports | 1 x PoE Out |
|---|---|
| PoE standards | 802.3af |
| PoE Max Power per Port (at PSE) | 15 W (only available if device is powered by |
802.3at PoE In)
NETWORK
Routing| Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP,
NHRP), Policy based routing
---|---
Network protocols| TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP,
FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP,
SNMP, MQTT, Wake On Lan (WOL)
VoIP passthrough support| H.323 and SIP-alg protocol NAT helpers, allowing
proper routing of VoIP packets
Connection monitoring| Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP
for link inspection
Firewall| Port forward, traffic rules, custom rules
Firewall status page| View all your Firewall statistics, rules, and rule
counters
Ports management| View device ports, enable and disable each of them, turn
auto-configuration on or off, change their transmission speed, and so on
Network topology| Visual representation of your network, showing which devices
are connected to which other devices
DHCP| Static and dynamic IP allocation, DHCP Relay
QoS / Smart Queue Management (SQM)| Traffic priority queuing by
source/destination, service, protocol or port, WMM, 802.11e
DDNS| Supported >25 service providers, others can be configured manually
Network backup| VRRP, Wired options, each of which can be used as an automatic
Failover
Hotspot| Captive portal (Hotspot), internal/external Radius server, SMS
authorization, internal/external landing page, walled garden, user scripts,
URL parameters, user groups, individual user or group limitations, user
management, 9 default customizable themes and option to upload and download
customised hotspot themes
SSHFS| Possibility to mount remote file system via SSH protoco
SECURITY
Authentication| Pre-shared key, digital certificates, X.509 certificates,
TACACS+, Radius, IP & Login attempts block
---|---
Firewall| Pre-configured firewall rules can be enabled via WebUI, unlimited
firewall configuration via CLI; DMZ; NAT; NAT-T
Attack prevention| DDOS prevention (SYN flood protection, SSH attack
prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-
RST, X-mas, NULL flags, FIN scan attacks)
VLAN| Port and tag-based VLAN separation
Mobile quota control| Mobile data limit, customizable period, start time,
warning limit, phone number
WEB filter| Blacklist for blocking out unwanted websites, Whitelist for
specifying allowed sites only
Access control| Flexible access control of SSH, Web interface, CLI and Telnet
VPN
OpenVPN| Multiple clients and a server can run simultaneously, 27 encryption
methods
---|---
OpenVPN Encryption| DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC
192, DESX-CBC 192, BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64,
AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128,
AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192,
AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192,
AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256,
AES-256-OFB 256, AES-256-CBC 256
IPsec| IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128,
AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12,
AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)
GRE| GRE tunnel, GRE tunnel over IPsec support
PPTP, L2TP| Client/Server instances can run simultaneously, L2TPv3, L2TP over
IPsec support
Stunnel| Proxy designed to add TLS encryption functionality to existing
clients and servers without any changes in the program’s code
DMVPN| Method of building scalable IPsec VPNs
SSTP| SSTP client instance support
ZeroTier| ZeroTier VPN client support
WireGuard| WireGuard VPN client and server support
Tinc| Tinc offers encryption, authentication and compression in it’s tunnels.
Client and server support
OPC UA
| Supported modes | Client, Server (planned) |
|---|---|
| Supported connection types | TCP |
MODBUS
| Supported modes | Server, Client |
|---|---|
| Supported connection types | TCP |
| Custom registers | MODBUS TCP custom register block requests, which read/write |
to a file inside the router, and can be used to extend MODBUS TCP Slave
functionality
Supported data formats| 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB
first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian),
CDAB, BADC), HEX, ASCII
DATA TO SERVER
| Protocol | HTTP(S), MQTT, Azure MQTT |
|---|---|
| Data to server | Extract parameters from multiple sources and different |
protocols, and send them all to a single server
MODBUS MQTT GATEWAY
Modbus MQTT Gateway| Allows sending commands and receiving data from MODBUS
Master through MQTT broker
---|---
DNP3
| Supported modes | Station, Outstation |
|---|---|
| Supported connection | TCP |
DLMS
| DLMS Support | DLMS – standard protocol for utility meter data exchange |
|---|
MONITORING & MANAGEMENT
WEB UI| HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event
log, system log, kernel log
---|---
FOTA| Firmware update from server, automatic notification
SSH| SSH (v1, v2)
SMS| SMS status, SMS configuration, send/read SMS via HTTP POST/GET
Call| Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a
timer
TR-069| OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS,
LibCWMP, Friendly tech, AVSystem
MQTT| MQTT Broker, MQTT publisher
SNMP| SNMP (v1, v2, v3), SNMP Trap
JSON-RPC| Management API over HTTP/HTTPS
MODBUS| MODBUS TCP status/control
RMS| Teltonika Remote Management System (RMS)
IoT PLATFORMS
Cloud of Things| Allows monitoring of: Device data, Mobile data, Network info,
Availability
---|---
ThingWorx| Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name,
Mobile Signal Strength, Mobile Network Type
Cumulocity| Allows monitoring of: Device Model, Revision and Serial Number,
WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator,
Signal Strength
Azure IoT Hub| Can send device IP, Number of bytes send/received, Temperature,
PIN count to Azure IoT Hub server, Mobile connection state, Network link
state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State,
PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ,
CELL ID, Operator, Operator number, Connection type
SYSTEM CHARACTERISTICS
| CPU | Mediatek, 580 MHz, MIPS 24KEc |
|---|---|
| RAM | 128 MB |
| FLASH storage | 16 MB |
FIRMWARE / CONFIGURATION
WEB UI| Update FW from file, check FW on server, configuration profiles,
configuration backup
---|---
FOTA| Update FW
RMS| Update FW/configuration for multiple devices at once
Keep settings| Update FW without losing current configuration
FIRMWARE CUSTOMIZATION
| Operating system | RutOS (OpenWrt based Linux OS) |
|---|---|
| Supported languages | Busybox shell, Lua, C, C++, and Python, Java in Package |
manager
Development tools| SDK package with build environment provided
GPL customization| You can now create your own custom firmware and web page
application, with some examples to make the creation process easier; and brand
our firmware by changing colours, logos, and so on to fit your or your
clients’ needs
INPUT / OUTPUT
| Events | Email, RMS, SMS |
|---|
POWER
| Connector | RJ45 Socket |
|---|---|
| Input voltage range for PoE | 42.5–57.0 VDC, reverse polarity protection, |
voltage surge/transient protection
Power consumption| Idle: < 2.5 W / Max: < 6 W / PoE Max < 21 W
PHYSICAL INTERFACES
| Ethernet | 2 x RJ45 ports, 10/100 Mbps |
|---|---|
| Status LEDs | 3 x Mobile connection type, 3 x Mobile connection strength, 4 x |
ETH status LEDs
SIM| 2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V
Power| RJ45, PoE In, 42.5 – 57.0 VDC
Antennas| 2 x Internal antennas
Reset| Reboot/User default reset/Factory reset button
PHYSICAL SPECIFICATION
| Casing material | Plastic (PC+ASA) |
|---|---|
| Dimensions (W x H x D) | 110 x 49.30 x 235 mm |
| Weight | 855 g |
| Mounting options | Mounting Bracket (for vertical flat surface or pole |
mounting)
OPERATING ENVIRONMENT
| Operating temperature | -40 °C to 75 °C |
|---|---|
| Operating humidity | 10% to 90% non-condensing |
| Ingress Protection Rating | IP30 |
REGULATORY & TYPE APPROVALS
| Regulatory | CE, UKCA, EAC, UCRF, RCM |
|---|
STANDARD PACKAGE*
- OTD140 Router
- Router Holder
- QSG (Quick Start Guide)
- Packaging Box
OTD140 ROUTER
|
ROUTER HOLDER
|
QSG (QUICK START GUIDE)
---|---|---
- Standard package contents may differ based on standard order codes.
CLASSIFICATION CODES
HS Code: 851762
HTS: 8517.62.00
For more information on all available packaging options please contact us directly.
AVAILABLE VERSIONS
HARDWARE VERSION| SUPPORTED FREQUENCIES| STANDARD ORDER CODE /
PACKAGE CONTAINS
---|---|---
OTD140 0***
Australia, Europe, Asia-Pacific| 4G (LTE-FDD): B1, B3, B5, B7, B8, B20,
B28
4G (LTE-TDD): B38, B40, B41
3G: B1, B5, B8
2G:** B3, B8| OTD140 000000 / Standard Package
The price and lead-times for region (operator) specific versions may vary. For more information please contact us.
1 – Regional availability – excluding Russia & Belarus
2 – For more detailed information about certified carriers, visit our Wiki
page
OTD140 SPATIAL MEASUREMENTS & WEIGHT
MAIN MEASUREMENTS
W x H x D dimensions for OTD140:
Device housing*:| 110 x 49.30 x 235 mm
Box:| 355 mm x 175 mm x 60 mm
*Housing measurements are presented without antenna connectors and screws; for measurements of other device elements look to the sections below.
TOP VIEW
The figure below depicts the measurements of OTD140 and its components as seen from the top:
RIGHT VIEW
The figure below depicts the measurements of OTD140 and its components as seen from the right side:
FRONT VIEW
The figure below depicts the measurements of OTD140 and its components as seen from the front panel side:
MOUNTING SPACE REQUIREMENTS
The figure below depicts an approximation of the device’s dimensions when cables and antennas are attached:
Copyright © 2024, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>