MOUNT-IT MI-2757 Freestanding Monitor Arm with Height Adjustment Instruction Manual

: June 17, 2024
: Mount-It

Table of Contents

Thank you for choosing Mount-It
Mount and Accessories
Mounting Hardware
DIMENSIONS & WEIGHT CAPACITY
Instruction For Use
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MOUNT-IT MI-2757 Freestanding Monitor Arm with Height Adjustment

MOUNT-IT MI-2757 Freestanding Monitor Arm with Height
Adjustment

Thank you for choosing Mount-It

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-It! for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Please closely follow the assembly instructions. Improper installation may result i171 damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

Mount and Accessories

A (x1)
Stand Arm
B (x1)
Stand Base
C (x4)
M6x12
Bolt
D (x1)
4mm
Hex Wrench
E (x1)
5mm
Hex Wrench

Mounting Hardware

M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation.

CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.

Missing Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.

DIMENSIONS & WEIGHT CAPACITY

Rated weight capacity is 17.6lbs.
Caution:
Ensure all mounting surfaces are capable of holding the weight of your mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

Dimensions & Weight Capacity

Instruction For Use

Step 1

Connect the Base and Arm

Connect the Stand Base (#B) to the bottom of the Stand Arm (#A) using the Bolts (#C) and tighten until secure using the 4mm Hex Wrench (#D)

Step 2

Attach the Monitor

Select the appropriate size mounting bolt (#M-A or M-B) and washer (#M-C) for your monitors mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your monitor user manual or contact the monitor manufacturer for sizing information.
Partially install the top 2 VESA bolts, leaving a gap of approximately 0.1” between the monitor and the back of the bolt head.

Step 3

Attach the Monitor

Hang the monitor onto the top of the VESA Plate as shown here, then secure the monitor to the bottom 2 bolt holes and tighten all bolts until secure.
Monitor cables can be routed through the cable clip on the back of the arm.

Step 4

Final Adjustments

Final Adjusments

To properly balance the arm with monitors mounted, adjust the spring tension using the supplied Allen Key as follows:

First, position and firmly hold the arm horizontally as shown. Ask for assistance should you require it.

Symbols

CAUTION: To avoid damage to monitors or mount, always keep the arm in a horizontal position while making adjustments. Again, ask for assistance if required.

If the arm drops, turn the adjustment screw clockwise until it stays in a horizontal position.

If the arm rises, turn the adjustment screw counter-clockwise until it stays in a horizontal position.

CAUTION: DO NOT over tighten the screws.

The Monitor can be turned left to right +/- 25°, tilted forward or back +10°/-15° and rotated 90° to alternate between landscape and portrait orientations.