American Standard 7390.713 Hampton Bidet Faucet Transfer Valve Instruction Manual

American Standard 7390.713 Hampton Bidet Faucet Transfer Valve

Instructions

Bidet Faucet and Transfer Valve with EverClean™ Finish & SpeedConnect™ Drain
Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain, two features found only on American Standard faucets.

EverClean Finish

• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful for the life of the faucet
• EverClean TM available on: Polished Chrome, Satin Nickel,
• Stainless Steel, Polished Brass (or any combination of these finishes)

SpeedConnect Drain

• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

BIDET FAUCET INSTALLATION

• Place RUBBER RING (10) into ESCUTCHEON (4).
• Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of the mounting surface, install VALVE BODY (3, 3a) through valve mounting until snug against the internal stop. If necessary, adjust LOCKNUT (1).
• Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a).
• Remove ESCUTCHEON (6), WASHER (7) and UPPER GASKET (8) from TRANSFER VALVE (9). Insert TRANSFER VALVE (9) into the center forward hole of BIDET.
• Replace UPPER GASKET (8) and WASHER (7) and ESCUTCHEON (6) until it locks against the internal stop. Position the side-threaded outlet rearward and secure MOUNTING NUT (11).

SPRAY INSTALLATION

• Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NÚT (3).
• Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1) Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8).
• Thread SPRAY CAP (9) onto SPRAY BODY (1).

POP-UP DRAIN

• Remove CLEAR PLASTIC COVER (1).
• Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3).
• Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B.

 REMOVE FLANGE

•  Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A.
• Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.

INSTALL DRAIN FROM BELOW FIXTURE

• From under side of BIDET install DRAIN BODY (1) up through drain outlet. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the BIDET.
• Install FOAM GASKET (3) and FLANGE (4) onto drain body from above BIDET and tighten FLANGE (4) firmly.

TIGHTEN LOCKNUT

• lighten LDCKNUT  firmly with an Adjustable Wrench or Channel Locks.

FLANGE GASKET

• Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET (1) is fully compressed and not visible. Fig. A. POP-UP ROD ASSEMBLY
• Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR (2) through rear hole, making sure SEAL WASHER (3) is properly seated. Fig. B.
• From below slip slot in MOUNTING NUT (4) over CABLE (5) Thread NUT (4) onto lift rod guide shank to secure ROD GUIDE (1) to bidet. Hand tighten only. Fig. B.

ATTACH CABLE CONNECTOR

• POP-UP KNOB (1) must be fully down. Fig. A.
• Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. B.
  • Your new POP-UP DRAIN installation is now complete. Fig.
  • C. Note: Tailpeice on pop-up drain is 1-1/4″ O.D. Fig. C.

CHECK OPERATION OF POP-UP

• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. INSTALL DIVERTER KNOB
• Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2).
• Push on RING (3) and tighten with SCREW (4).
• Press on KNOB CAP (5). Note: The screwdriver gap is for disassembling and should point downwards.

TEE AND HOSE CONNECTION

• Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to side of TRANSFER VALVE (3).
• Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2).
• Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tainted.

WATER SUPPLY CONNECTION
NOTE
FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY

• Connect water supply to VALVE BODIES (7,7a) with 1/2″ IPS FLEXIBLE SUPPLIES (8) or 3/8″ O.D. BULL-NOSE RISERS (9). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply wher bending. Use tubing cutter to cut to proper length.
• Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.
• Connect 1-1/4″ O.D. tailpiece on POP-UP DRAIN to waste outlet.

INSTALL HANDLES (Lever)

• Turn VALVE into OFF position.
• Push ADAPTER (1) into HANDLE BASE (2) in a way that the male square on the ADAPTER (1) fits in the female square of the HANDLE BASE (2).
• Push HANDLE BASE (2) and ADAPTER (1) onto VALVE STEM (5).
• Check alignment, if not satisfactory aligned;
  • Push out ADAPTER (1) carefully.
  • Turn ADAPTER (1) either 45° or 90° so that the male square on ADAPTER (1) catches the different female square in HANDLE BASE (2).
• Secure HANDLE BASE (2) with HANDLE SCREW (3).
• Push INDEX CAP (4) in hole of LEVER BALL (6).

INSTALL HANDLES (Cross)

• Turn VALVE into OFF position.
• Push ADAPTER (1) into HANDLE square on the ADAPtER mile in the female square of the HANDLE BASE (2).
• Push HANDLE BASE (2) and ADAPTER (1) onto VALVE STEM (5)
• Check alignment, if not satisfactory aligned;
• Secure HANDLE BASE (2) and METAL CROSS (6) or PORCELAIN CROSS (7) with HANDLE SCREW (3).
• Push INDEX CAP (4) in hole of METAL CROSS (6) or PORCELAIN CROSS (71.

TEST INSTALLED FITTING

• With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks.
• Operate both HANDLES (1) to flush water lines thoroughly.
• Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation.

CHECK DRAIN CONNECTIONS

• Pull up POP-UP KNOB (3) and fill Bidet with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Bidet. If STOPPER (4) does not seal properly. please refer to
• “Troubleshooting Guide” in these instructions. Push POP-UP KNOB (3) down and check all drain connections and “P” trap for leaks. Tighten if necessary.

EverClean™ Finish Care Instructions

• American Standard’s EverClean finish will wipe clean with a soft, dry cloth.
• A soft cloth with clean water may also be used, if desired.
• No additional cleaning products are required.
• DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.

SERVICE

To change the direction of handle rotation, proceed as follows:

• Turn valve to OFF position
• Remove INDEX (1) and HANDLE SCREW (2). Pull HANDLE (3) off. Remove ADAPTER (4). Remove SPRING CLIP (5). 7
• Lift STOP WASHER (6), turn 90* and replace.
• Replace SPRING CLIP (5). Replace ADAPTER (4), HANDLE (2), SCREW (2), and INDEX (1).
• If spout drips, operate handles several times from OFF to ON position.
• Do not farce . handles turn only ON°

If spout drips, operate handles several times from OFF to ON position. Do not force – handles turn only 90°

SpeedConnect™ Drain

• If sink does not hold water even though Stopper is in the “down” position:
  • Follow CABLE ADJUSTMENT PROCEDURE.
• If sink does not hold water even though Stopper is in the “down” position:
  • Follow CABLE ADJUSTMENT PROCEDURE.
• If you need to remove the Stopper:
  • Follow STOPPER REMOVAL PROCEDURE.
• If you would like the ability to remove your Stopper simply by lifting it out of the drain:
  • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• • Loan the lustration. Pig. Body where the Cable was attached and locate the component labeled as
• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C.
• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
• Bruit on the hele to the and handy Cation A2) by threading the Cable Connector (1) clockwise onto the Drain Body Connection (2) and hand-tighten. Fig. A.

STOPPER REMOVAL PROCEDURE

• Disconnect the Cable from the Drain by threading the Cable Connector 111 counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as ·cam· and “Cam Cap· in the illustration. Fig. B.
• Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
• The Stopper can now be removed by lifting it out of the Drain. Fig. F.

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, 11Lacked11 Made (Stopper cannot be removed) or 11Unlack11 Made (Stopper is removable). Lacked Made:

• Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G.
• To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.Fig. G.
• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in Troubling Shooting Guide to complete installation. Stopper will be in “Locked” mode and not be removable.

Unlocked Made:

• Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H.
• To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H.
• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in ‘Troubling shooting Guide” to complete installation. Stopper will be in “Unlocked” mode and removable

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>