TESY GH 200/ GH 200 B 2-8 Glass Panel Heater Instruction Manual

TESY GH 200/ GH 200 B 2-8 Glass Panel Heater

IMPORTANT SAFETY PRECAUTIONS

WARNING

• Please read this manual before operating the appliance and keep it at a safe place for future reference. In case the appliance is obtained by a new owner, it should be transferred together with its manual.

• CAUTION: Children under 3 years of age should be kept away from the appliance unless they are under constant supervision.
  Children from 3 to 8 years of age are allowed to operate the on/off button ONLY, provided that the appliance is installed and ready for operation and such children have been supervised and instructed in safe operation of the appliance and they understand all related risks.
  Children from 3 to 8 years of age MUST NOT: connect the plug to power sockets, make adjustments, clean it or carry out user maintenance operations.
  This appliance can be used by children older than 8 years of age and by people with reduced physical, sensor and mental capabilities, as well as by people with insufficient experience and knowledge provided they are supervised or instructed in safe operation of the appliance and understand the related risks. Children should not be allowed to play with the appliance. Cleaning and user maintenance operations must not be carried out by children without supervision.

• CAUTION: Some of the appliance parts may get very hot during operation and thus cause burns to users. In case there are children and vulnerable people in the room, special attention should be paid.

• WARNING: In order to avoid overheating, do not cover the appliance!

• The appliance should not be positioned close under power sockets!

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Before connecting the fan heater, you should check if the voltage on the technical information plate corresponds to the voltage of the main electrical system of the place of use /at home or in the office/. The appliance is intended for the voltage, shown on the technical information plate.

• GH 200/ GH 200 B glass panel heater must be installed in accordance with the good professional practices and in accordance with the legislature of the particular state (Electricity Directive of EU and requirements for special installations and places of installation including bathroom or shower box HD60364-7-701:2007(IEC 60364-7- 701:2007)).

• The heater is classified as class II and is provided with IPX4 water protection. For that reason it must be mounted
  in position (VOLUME) 2. That prevents the chance of reach to the control board (switch and thermostat) of the fan heater by a person who is in a shower or in a bath. Minimum permissible distance between the appliance and a water source must not be less than 1 meter! The appliance is to be mounted on a wall only!

This appliance must be used only with its main function, which it was intended for, i.e. heating of domestic premises. Every different usage is considered incorrect and hence dangerous. The manufacturer does not assume responsibility for break-downs, caused by incorrect and unreasonable usage. Non-adherence to the safety precautions will render the guarantee invalid

• Do not leave your home, while the appliance is turned on: assure that the switch is in position OFF(0) (turned-off) and the thermostat switch is in position – minimum. Always disconnect the plug of the device from the socket.
• Keep inflammable objects as furniture, cushions, bedding, paper, clothes, curtains etc. at a distance of minimum 100 cm away from the fan heater.
• Do not use the device in areas of usage and storage of inflammable substances. Do not use the device in combustible areas /for example near inflammable gases and aerosols/ – there is a great risk of explosion and fire!
• Do not insert or allow any objects to get into the ventilation openings (inlets and outlets), because that can cause break-down of the appliance or any other damages.
• The appliance is not suitable for animal breeding and is intended only for domestic use!
• Keep the air outlet free from any objects: you should keep a clear distance of at least 1m in front the heater. Do not allow any objects to get into in the air inlet or outlet because that can cause electrical shock, fire or damage of the heating element.
• The most common reason for over-heating is the accumulation of dust and dirt in the appliance. You should clean regularly ventilation openings with a vacuum cleaner. Before cleaning you must disconnect the appliance from the mains. Keep the fan heater always clean.
• You should never touch the appliance with wet or moist hands – there is danger for your life!
• In order to disconnect the plug from the socket outlet when necessary the socket should be accessible all the time!
• You must never pull the electric cord or the appliance itself when disconnecting from the mains
• Warning! The air outlet gets hot when the appliance is operating (more than 80°С).
• Do not cover the appliance. If the appliance is covered there is danger of overheating.
• The electrical system to which the appliance is connected must be provided with automatic safety fuse. The distance between the sockets and the appliance (in turned-off state) must be at least 3mm.
• Grounding is forbidden! After unpacking and before use you must check if the mechanical parts and their gear are in a good state. If you have any doubts you should not use the appliance and search advice from a qualified electrician.
• If the appliance is damaged or not functioning properly you must stop it and not try to repair it yourself. For any type of repairs you must consult the Service Center for post-sale help. There you will have your damaged part replaced with an original spare one. Not obeying this instruction will compromise the appliance safety.
• If you decide to stop using an appliance of that kind it is recommended to make it unusable as you cut the electric cord, after you have disconnected it from the mains. It is also recommended all hazards, related to the appliance to be checked. That is very important if there is a chance the discarded appliance to be used for play by children.
• You should never keep the appliance unnecessarily plugged-in. Disconnect the appliance from the mains if you do not intend to use it for a long time.
• In order to avoid any overheating of the electric cord it is recommended to unreel the whole electric cord.
• Warning: Do not use this appliance with a programmer, counter or another device which can automatically turn it on because if the appliance is covered or incorrectly positioned there is a danger of fire.
• Place the electric cord in such a way that it does not hamper the movement of people and not to be stepped on! You must use only approved connection blocks, which are suitable for the appliance, i.e. there is a sign of compliance!
• The electric cord must not be in touch with the hot parts of the appliance!
• You must never move the appliance by pulling it by its electric cord. You must never use the electric cord for moving of other objects.
• Do not reel the electric cord round the appliance! Do not use the appliance with its electric cord reeled – this is also valid if a cable drum is used!
• Do not press the cord and do not stretch it by sharp edges. Do not place the cord over hot plates or in open fire!
• This appliance is intended only for drying textiles washed in water.

PACKAGE

• After unpacking the appliance you should check if it is not damaged during transportation and if all the components are included! In case that you find out any damage or incomplete package you should connect with your authorized retailer!
• Do not discard the original packing box! It could be used to store the appliance during transportation in order damages to be avoided!
• The disposal of the packing material should be done in the appropriate way! Children should be prevented from playing with the polyethylene bags!

MOUNTING ON A WALL

1. Please ensure that the walls of the installation location without wires, pipes, etc., to ensure that the device can be securely mounted on the wall
2. The appliance is intended only for vertical wall mounting! Floor or ceiling mounting is forbidden!
3. Never position the appliance right below a socket outlet!
4. The appliance should be assembled and connected by a qualified electrician. The installation process should be isolated from the mains before electrical connection works are to be done.
5. Position the power cord so that it does not hamper free movement of people and not to be stepped on! Use only approved extensions, which are proper to the appliance, i.e. they have a compliance sign!
6. The power cord should not be in touch with hot parts of the appliance!
7. Do not use the appliance in rooms smaller than 4 square meters.
8. The appliance inlet and outlet openings must not be blocked! Distance between the appliance and the ceiling is at least 0.2m. Distance on both sides of the appliance to the wall is at least 0.25m. Distance between the outlet and the bottom is min 0.5m.

FIXATION OF THE APPLIANCE ON WALL

1. Choose a wall on which there is enough space
2. Use a Ø6 drill to drill 4 holes according to following positions:
3. Fit the pegs from the accessory bag in these holes.
4. Detach the up-hook from the back of the appliance and put it in the position of the two pegs at the top. Fix the up-hook on wall with two ST4X35 screws.
5. Insert the two filters in the left and right card slot, tighten them with two ST3X10 screws (notice for the screw position).
6. Put the two Z wall hanging brackets on the back of the appliance with two M4X8 screws, put the small towel rack into the fixed slot and lock with four M4X16 screws, and then put the big towel rack into the fixed slot and lock with four M4X16 screws.
7. Assemble the appliance on the up-hook, tighten two M4X10 screws on the right side and two M4X10 screw on the left side to fix the appliance (two people to assemble).
8. Fix the Z wall hanging brackets on the wall with two ST4X35 screws.
9. Use the cloth to clean the surface.
   We thank you for choosing GH 200/ GH 200 B glass panel heater. The appliance will provide long-life service if being correctly maintained and taken care of in accordance with the manual.

INSTRUCTION FOR USE

Connect to supply power, push the ON/OFF (0/I) button located at the left side of the appliance to switch on the appliance. Buzzer will have a short “D” sound and full screen display will light up for 1 min, then automatically switch to standby mode. Push ON/OFF button again, if you want to switch off.

Set date and time:
The date and time setting can be done only when the appliance is in standby mode.

Press SET, the day icon flashes. Use + and – to set current day. Then press OK, the hour icon flashes. Use + and – to set hour. Then press OK, the minute icon flashes. Use + and – to set minute. In the end, press OK to confirm and finish day and time setting. (Once day is set, the current day will be highlighted.)

Manual mode:
Press .

start at 1800W (screen display ), the following operation could be conducted

1. Temperature setting

   • Press SET once, the screen will flash 20°C (default temperature is 20°C)
   • Use + or – to set temperature (5-40°C) and then press OK to confirm setting
   • Heater will stop heating when ambient temperature reaches the set temperature. When ambient temperature is 2°C lower than the set temperature, heater will restart heating.
     When temperature setting finish: the screen will automatically display the setting temperature in working mode (SET icon and the setting temperature will light up). Press OK to read room temperature. It will automatically switch back to setting temperature in 5 seconds. The screen will display room temperature in standby mode or towel heating mode. (SET icon will not light up when room temperature is displayed only)

2. Mode Switch
   Press once to switch mode among 1800W ( ), 900W and cooling fan in cycle. The relevant icon will light up during mode switch.

Towel Heating Function

• Connect to supply power, press once to switch on towel heating function, to press  it again to switch it off. During towel heating mode, icon lights up all the time. Towel heating working power is 200W.
• Towel heating function works individually. It could be conducted when the appliance is in standby mode. Working period is 2 hours each time. It will automatically switch off in 2 hours when nobody switches it off manually.

Note: The temperature SET should be higher than the room temperature (the temperature icon on the left). Otherwise, the appliance will not start heating.

Program mode:

In standby mode, long press   for 3 seconds, flashes until program setting finishes:

Set Wake Up Time and Temperature:

Screen full displays, which mean you are setting wake up time for the whole week, use + and – to set current day, the selected day will flash, press ok to confirm. Then hour icon will full display (one box stands for one hour, totally 24 boxes for 24 hours). Use + and – and/or SET button to set hour, the selected box will flash. You may set the start hour or a working time range.

For example:

1. Set the heater to start at 8:00 a.m., use + and – to select the 8th box, it will flash, press OK to confirm it.
2. Set the heater to start work at 8:00 am and stop at 10:00 a.m., firstly use + and – to select the 8th box, then press SET, use + and – to select the 9th box, these 2 boxes will flash, press OK to confirm it.

Then the SET temperature 20°C (default temperature is 20°C) flashes. Use + and – to set target wake up temperature (5-40°C).
Then press OK to move on to the next day wake up time and temperature setting in the same way.
In the end, press OK to confirm and end the setting. All icons will stop flashing.
(During the setting, you can press SET to activate/shut down the wake up program for week-days.)

Note:

1. when week timer is set, icon will display all the time. If you don’t need week timer, press once to switch it off, the icon on screen will disappear at the same time.
2. In week timer program, press to switch off the current day program mode. It will works automatically in next day as pre-set program.

Body Detector (Motion Sensor)
Body detector only works when wake up time and temperature are set. It starts to scan the surroundings when the preset wake-up time comes and heater starts heating.

1. When nobody is detected, heater will stop heating in 15 mins.
2. When somebody is detected, heater will keep heating until the room is detected to be empty. It will stop heating 15 mins later after that.
3. When somebody is detected again, heater will recover to work again.

Intelligent Window Open Detection

Long press   for 3 seconds to switch on window open detection mode. It will work and start to count once ambient temperature is found to drop as much as 5°C within 10 minutes. 30 minutes later

1. If ambient temperature is lower than / or the same as before, heater will switch to standby mode automatically.
2. If ambient temperature is higher than before, detection will go on.

Press   again to switch off the window open detection

Note : Intelligent window open detection mode cannot work under program mode.

Nute

1. In manual mode and program mode, press , to stop working. Towel heating function will not be affected by this operation.
2. The appliance will not work when setting temperature is lower than ambient temperature. Towel heating function and cooling fan function will not be affected by this operation.
3. The heater is switch off under whatever mode, motor impeller will keep moving for extra 60 seconds to release internal heat before stop.
4. In whatever working mode, display screen and pilot lamp become dark in 1 minutes when no operation is conducted. Press any button to activate the screen and pilot lamp to go on operation.
5. Long press SET for 5 seconds to recover factory setting, which mean setting week and time recover to factory setting.

Filter clean
Filter becomes dirty during use or after 720 hours (month) use, the display flashes CL. Press OK. Turn the appliance off, then remove the filter on the back of the appliance. Clean the filter directly under water. Do not use caustic or abrasive material during cleaning, as this can damage the filter. Then, have the filter dried naturally.

Then reassemble the filter according to the reference line (see below drawing).
Push the filter to the end until it cannot move anymore.

OVERHEATING PROTECTION

The in-built overheating protection automatically turns the appliance off in case of an error! In that situation the plug must be disconnected from the mains and the control switch put in position “0”. After a short period of cooling the appliance is ready for operation (in about 10-15 minutes)! If that error is repeated – consult an authorized service at your location!

CLEANING

• You must first turn off the appliance and disconnect its plug from the socket. Do not use abrasive detergents!
• Clean the body with wet cloth, vacuum cleaner or a brush!
• You must never submerge the appliance under water – there is life danger!
• If the appliance should not be used for a certain period of time it must be secured from excessive dirt and dust by placing it in its original package.
• You must never place the hot appliance in its package!

Instructions for environment protection
Electric appliances out of use contain valuable materials and hence must not be disposed in domestic dumbs! We kindly ask you for cooperation and active role in preservation of natural resources by disposing the appliance to the organized buy-back locations (if there are any).

TABLE 2: INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS Model identifier(s): 1.GH 200/ GH 200 B 2000W/230-240V~ 50Hz

charge control, with room and/or outdoor temperature feedback heat charge control, with integrated thermostat| [yes/no]
Auxiliary electricity consumption| | | | Fan assisted head output| [yes/no]
At nominal heat output| elmax| N/A| kW| Type of heat output/room temperature control (select one)| –
At minimum heat output| elmin| N/A| kW| Single stage heat output and no room temperature control| [no]
In standby mode| el SB| 0.0009| kW| Two or more manual stages, no room temperature control| [no]
| With mechanic thermostat room temperature control| [no]
With electronic room temperature control| [no]
With electronic room temperature control plus day timer| [no]
With electronic room temperature control plus week timer| [yes]
Other control options (multiple selections possible)|
Room temperature control, with presence detection| [yes]
Room temperature control, with open window detection| [yes]
With distance control option| [no]
With adaptive start control| [no]
With working time limitation| [yes]
With black bulb sensor| [no]

TESY Ltd – Head office
1166 Sofia, Sofia Park,
Building 16V, Office 2.1. 2nd Floor PHONE: +359 2 902 6666,
FAX: +359 2 902 6660,
office@tesy.com
8 Usage and Storage Instructions

References

• TESY Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>