TESY CN03 YYZ MIS F Portable Electric Convector Heater User Manual

June 1, 2024
TESY

TESY CN03 YYZ MIS F Portable Electric Convector Heater

This product is only suitable for well-insulated spaces or occasional use.

IMPORTANT SAFETY MEASURES AND INSTRUCTIONS

WARNING!

  • Please read this manual before operating the appliance and keep it in a safe place for future reference. In case the appliance is obtained by a new owner, it should be transferred together with its manual.
  • CAUTION: Children under 3 years of age should be kept away from the appliance unless they are under constant supervision.
  • Children from 3 to 8 years of age are allowed to operate the on/off button ONLY, provided that the appliance is installed and ready for operation such children have been supervised and instructed in the safe operation of the appliance and they understand all related risks.
  • Children 3 to 8 years of age MUST NOT: connect the plug to power sockets, make adjustments, clean it, or carry out user maintenance operations.
  • This appliance can be used by children older than 8 years of age and by people with reduced physical, sensor, and mental capabilities, as well as by people with insufficient experience and knowledge provided they are supervised or instructed in the safe operation of the appliance and understand the related risks. Children should not be allowed to play with the appliance. Cleaning and user maintenance operations must not be carried out by children without supervision.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
  • CAUTION: Some of the appliance parts may get very hot during operation and thus cause burns to users. In case there are children and vulnerable people in the room, special attention should be paid.
  • WARNING: Do not cover the appliance to prevent overheating!
  • The appliance must not be placed right under a socket box!
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
  • Before connecting the appliance to the mains, check if the voltage indicated on its technical plate corresponds to the voltage of the electricity, supplied to your house.
  • This appliance shall be used only for the purpose it has been designed and intended for, i.e. heating of domestic premises. The appliance is not intended for commercial/industrial applications. Every other use is to be considered improper, and therefore dangerous. The manufacturer doesn’t bear responsibility for damages arising from improper and irrational use. Non-adherence to these instructions would render the warranty invalid!
  • Do not leave your home while the portable electric convector heater is operating: make sure that the power switch is in the OFF position (Portable electric convector heaters with mechanical control).
  • Keep inflammable objects, such as furniture, pillows, bedding, paper, clothes, curtains, etc. at a safe distance of at least 100 cm away from the convector.
  • Do not operate the appliance in areas of use or storage of combustible substances. Do not operate the appliance in areas of combustible media (for example near inflammable gases or aerosols) – there is a great risk of explosion and fire!
  • Do not insert and do not allow foreign objects to enter the ventilation openings (inlet and outlet) because this will cause electric shock, fire, or damage to the appliance.
  • The appliance is not suitable for animal breeding. The portable electric convector heater is intended for domestic/indoor operation only.
  • When positioning the appliance, do not cover the safety grilles; do not hamper the incoming and outgoing airflow. All objects must be at a safe distance of at least 1 meter away from the appliance front and sides.
  • The most common reason for overheating is dust and fluff deposits in the appliance. Clean the ventilation openings regularly with a vacuum cleaner, but before that, it is very important to disconnect the portable electric convector heater from the mains.
  • Never touch the appliance with wet or moist hands – there is a risk for your life!
  • The power socket should be accessible all the time to disconnect the power plug when needed as fast as possible! Never pull the power cord or the appliance itself to disconnect it from the mains.
  • PAY ATTENTION! Outgoing air gets heated during appliance operation (up to more than 100°С).
  • If you decide to stop using an appliance of this kind, it is recommended to make it unusable by cutting its power cord after you have disconnected it from the mains. It is advisable all possible risks related to the appliance to be secured, especially in relation to children that may play with out-of-use appliances.
  • WARNING: Do not use this appliance with a programmer, counter or any other mechanism which could automatically turn on the portable electric convector heater – if the appliance is covered or positioned incorrectly there is a risk of fire.
  • Position the power cord in such a way that it does not obstruct the free movement of people and cannot be stepped on! Use only approved extension cords, which are suitable for this appliance, i.e. they have a compliance sign!
  • Never move the appliance by pulling its power cord; do not use the power cord for carrying other objects!
  • Do not bend the power cord and do not pull it against sharp edges; do not place the power cord on hot surfaces or open fire!
  • WARNING: To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1m from the air outlet.
  • Do not use this portable electric convector heater in the immediate surroundings of a bath, a shower or a swimming pool.
  • Do not use this portable electric convector heater if it has been dropped.
  • Do not use if there are visible signs of damage to the portable electric convector heater.
  • Use this portable electric convector heater on a horizontal and stable surface, or fix it to the wall, as applicable.
  • WARNING: Do not use the portable electric convector heater in small rooms, when they are occupied by persons not capable of leaving the room in their own, unless constant supervision is provided.

TECHNICAL PARAMETERS – SEE ANNEX I PACKING

  • After unpacking the appliance, check if its contents are intact and if it has not been damaged during transportation! In case a damaged or incomplete delivery is found, contact your authorized retailer!
  • Do not dispose of the original packing box! It could be used for storage and transportation purposes to avoid damages during transportation!
  • Disposal of packing material should be done appropriately! Children must be prevented from playing with polyethylene bags!

OPERATION AND INSTALLATION OF FEET SET

This portable electric convector heater is designed to be used indoors.

Dimensions of heated volume and heated area of a room/appliance models (fig.1)

TESY-CN03-YYZ-MIS-F-Portable-Electric-Convector-Heater-
fig-1

Model Heated volume Heated area
CN 03 050 MIS F – 500W 10* – 15 m3 4* – 6 m2
CN 03 100 MIS F – 1000W 20* – 30 m3 8* – 12 m2
CN 03 150 MIS F – 1500W 30* – 45 m3 12* – 18 m2
CN 03 200 MIS F – 2000W 40* – 60 m3 16* – 24 m2
CN 03 250 MIS F – 2500W 50* – 70 m3 20* – 28 m2
CN 03 300 MIS F – 3000W 60* – 80 m3 24* – 32 m2
  • Minimum guaranteed heated volume (area) for heating at an average capacity of heat transmission factor λ=0.5 W/(m2K) for a heated room. Higher values of heated volume (area) can be achieved at an average value of λ=0.35 W/ (m2K). Standard height of heated rooms – 2.5 meters.
    • By Regulation EU 2015/1188 implementing Directive 2009/125/EC this electric heating appliance is not intended for wall installation!

Important: In premises bigger than 45 m3, it is recommended to use a combination of 2 or more portable electric convector heaters.

  • Do not position the portable electric convector heater under a power socket or electricity connection box.
  • DO NOT install/operate the portable electric convector heater:
  1. in places where a draught is present, which could influence the control settings;
  2. right under a power socket;
  3. in “Volume 1” for bathrooms;
  4. in “Volume 2” if the control board can be reached by a person who is in a shower or in a bathtub;
    • Before starting the set installation check if the portable electric connector heater is disconnected from the power socket!
    • The feet are to be installed at the air inlets – it is correct for them to be installed at the two sides ends of the portable electric convector heater symmetrically – at the same distance from the sides ends of the portable electric convector heater. For installation purposes – all portable electric connector heaters have two 2×2 openings. (fig. 2a)
    • Mount the first foot – by inserting the higher part of the foot into the portable electric convector heater (you should stand opposite the face of the portable electric convector heater) – the part is lower than the front metal panel. Then you should take a Phillips screwdriver (not included in the product set) and screw in the two 3.5×9,5mm securing screws. The screw goes through the plastic foot and gets screwed into place in the metal body of the portable electric convector heater. You should repeat the same operation for the second foot. (fig. 2b)
    • The joint is secure in case the portable electric convector heater stands horizontally on the floor after its feet installation has been completed. Do not use the power cord as a pulling rope in order to move the portable electric convector heater; any movement of the portable electric convector heater should be done when it is cold.
    • Position the portable electric convector heater with installed feet on the floor and before connecting it to the power socket check if all instructions from the very beginning of this manual have been followed correctly (Important instructions and safety measures). The correct position is – the control electric should be at the top of the appliance and the feet – on the floor!TESY-CN03-YYZ-MIS-F-Portable-Electric-Convector-Heater-fig-2

BATHROOM OPERATION

  • The portable electric convector heater must be installed by the normal trade practices and in compliance with the national legislation (EU electricity directives and regulations concerning special installations and places of operation including bathrooms, shower cabins HD60364-7-701(IEC 60364-7- 701)). (fig. 3)TESY-CN03-YYZ-MIS-F-Portable-Electric-Convector-Heater-fig-3
  • In case this portable electric convector heater is to be used in a bathroom or other similar room, the following installation requirements must be observed: the portable electric convector heater has IP24 protection (water drops protection). Hence it can be installed in “Volume 2” (see the diagram below) to avoid the risk of the control board (power switch and thermo regulator) being reached by a person who is in a shower or a bathtub. The minimum distance between the appliance and a water source should be not less than 1 meter! If you do not feel sure about the installation of this portable electric convector heater in a bathroom, we recommend you consult a professional electrician.

Note: If the above-mentioned instructions cannot be implemented, it is recommended to install the appliance in “VOLUME 3”.

  • In wet premises, the power source must be installed at a height of at least 25 cm above the floor (bathrooms and kitchens).
  • The installation must be equipped with a safety fuse, and the distance between the fuse contacts in disconnected condition should be at least 3 mm.

Thank you for choosing the CN03 portable electric convector heater. This is a product providing heating in winter depending on the consumers’ needs for comfortable room temperature. If operated and taken care of properly by these instructions, the appliance will provide you with many years of useful operation.

OPERATION INSTRUCTIONS

MECHANICAL CONTROL

Operation modes – (fig. 4)

Turn the portable electric convector heater on by pushing the switch in position “I” (turned-on), then turn the regulator to the desired level (1 to 6) as you take into account the following relation between the power levels:

  • anti-freezing mode/ enabled when the room temperature falls below 5°C
  1. – economy mode/ it maintains low room temperature/This mode is recommended to be used at night and when there are no people present in the room. This mode permits to maintain the set room temperature while saving energy.
  2. – comfort mode/ it maintains moderate room temperature/This mode is recommended to be used to maintain a relatively high comfortable room temperature during the day.
  3. – maximum power mode / it maintains HIGH room temperature/This mode is recommended to be used when you need maximum high room temperature

Important: Thermo Regulator digits do not correspond to certain room temperature levels, but they can be used by users to memorize the relation between room temperature and the thermoregulator settings. When the room temperature is lower than the temperature that you have set by the thermo regulator, the portable electric convector heater starts its operation and will operate until the room temperature reaches the set temperature level of the unit. When the room temperature is higher than the adjusted temperature of the appliance, the portable electric connector heater will automatically go into “Stand by” mode.

PROTECTION

  • The appliance is equipped with a safety thermal turn-off device, which automatically turns the portable electric convector heater off in cases of extreme temperature of the portable electric convector heater /i.e. overheating of the appliance/.
  • The safety thermal turn-off device will automatically restore the portable electric convector heater operation when the temperature of the appliance falls below the permissible ultimate values.

TIP-OVER PROTECTION

This portable electric convector heater is protected with a safety switch that turns off the appliance automatically when the portable electric connector heater falls over or is at an excessive angle from the horizontal. This helps prevent accidents, and the portable electric convector heater will back to last set mode when it is put back upright.

CLEANING

  • It is compulsory first to turn off the appliance through its power switch and to disconnect it from the power socket. Before starting the cleaning session you should wait until the portable electric convector heater cools down in a disconnected state.
  • Clean the portable electric convector heater body with a damp cloth, vacuum cleaner or a brush.
  • Never immerse the appliance in the water – there is danger for your life from electric shock!
  • Never use gasoline, thinner or hard abrasive products to clean the appliance, because they will damage the appliance coating.

STORAGE

  • Before putting the portable electric convector heater away let it cool down after you have disconnected it from the power socket
  • Use the appliance’s original packing to store it, if the portable electric connector heater will not be in use for a long period. By storing the product in its original packing you protect it from excessive dirt and dust accumulation.
  • Never put a hot portable electric convector heater in its packing!
  • It is necessary the product to be stored at a dry and dark place, protected from direct sunlight.
  • It is explicitly forbidden to store the portable electric convector heater in damp premises.

MAINTENANCE OPERATIONS OF THE APPLIANCE

  • In case of appliance malfunction, please contact the authorized service center closest to your location. /service centers are indicated in appliance warranty documents/.
  • Important: In case of a claim and/or violation of your consumer rights, please contact the supplier of this appliance at the indicated locations or via the Internet page of the company: www.tesy.com

Environment protection instructions
Obsolete electric appliances contain valuable materials and consequently, they should not be treated as domestic waste! We ask for your cooperation and your active contribution to protect the resources and the environment. Please submit your out-of-use appliances to the organized buy-back stations (if there are such).

TROUBLESHOOTING

Prior to contacting the Customer Service Center, please check the items in the table below.TESY-CN03-YYZ-MIS-F-Portable-Electric-Convector-Heater-
fig-6

TABLE 2 : INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Model identifier(s)

  • Model identifier(s):/

TESY-CN03-YYZ-MIS-F-Portable-Electric-Convector-Heater-
fig-8TESY-CN03-YYZ-MIS-F-Portable-
Electric-Convector-Heater-fig-9TESY-CN03-YYZ-MIS-F-Portable-Electric-Convector-Heater-
fig-10TESY-CN03-YYZ-MIS-F-Portable-
Electric-Convector-Heater-fig-11

  • **P*** – EN Item/
  • TESY Ltd. Shumen, 9700, 48 Blvd. Madara,
  • PHONE: +359 54 859 129, office@tesy.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals