KUZCO VM40440-5CCT Hillmont LED Vanity Mirror Instruction Manual

KUZCO VM40440-5CCT Hillmont LED Vanity Mirror

Specifications

• Model: VM40440-5CCT
• Dimensions: [Insert Dimensions]
• Color Temperature Options: [Insert Color Temperature Options]

Product Usage Instructions

Installation:

1. Remove the mirror from its original package.
2. Measure and mark the location of the wall bracket (2a) on the wall. Mount the bracket to the wall using screws (2c) and anchors (2b). Ensure proper distance measurement based on Illustration 3. Make sure all screws are attached directly to a stud or structure.
3. Make proper electrical connections by connecting the black wire to the hot L, the white wire to the neutral N, and the ground wire to GND. Use the wire nuts (1a) provided in the hardware package. Connect the wires to an ON/OFF wall switch (wall switch provided separately). Note: The wall ON/OFF switch must be used to ensure proper operation of the LED mirror.

Securing the Mirror:

4. Bend both tabs of the wall bracket (2a) back to prevent the mirror from sliding side to side. Refer to Illustration 2 for guidance.
5. Align the mirror’s mounting bracket (3a) with the wall bracket (2a) to secure them together. Refer to Illustration 1 for guidance.

Adjusting Color Temperature and Dimming:

6. Gently tap the mirror switch (3b) to choose the desired color temperature. Hold the switch to dim the mirror up and down.

Frequently Asked Questions (FAQ):

• Q: What should I do if the mirror doesn’t turn on?
  A: Please ensure that the mirror is properly installed and that the electrical connections are correctly made. Also, make sure that the wall ON/OFF switch is turned on.

• Q: Can I install the mirror without using a stud or structure?
  A: No, it is important to attach all screws directly to a stud or structure to ensure proper installation and prevent any accidents or damage.

• Q: How do I choose the color temperature?
  A: You can choose the color temperature by gently tapping the mirror switch. Keep tapping until you reach your desired temperature. You can also hold the switch to adjust the brightness of the mirror.

START FROM HERE

• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your mirror installed by a certified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all times during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference

Important:
The installer and/or user must read, understand and follow these instructions before installing the product. This product must be properly installed before it is used. If instructions are not followed, the manufacturer will not be held responsible for any problems or product malfunction. Failure to follow installation and/or operating instructions voids the warranty.

Technical Support: 1-855-855-8926

Please Note:

• This Kuzco LED mirror comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
• For Indoor Use Only
• Touch Dimming
• Do not use alcohol or solvents to clean the mirror
• For your convenience, assembly by two people is a must

INSTALLATION INSTRUCTION

1. Remove mirror from its original package

2. Measure, mark location of wall bracket (2a) location, mount to wall with screws (2c) and anchors (2b) (See Illustration 3 for ideal distance measurement) (Note: All screws must be attached directly to stud/structure)

3. Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1a) provided in hardware package to ON/OFF wall switch (wall switch provided by others)
   NOTE : Wall ON/OFF Switch must be used to ensure proper operation of LED mirror

4. Bend both wall bracket (2a) tabs back to prevent mirror from sliding side to side (See Illustration 2). Align mirror (3a) mounting bracket to wall bracket (2a) to secure (See Illustration 1)

5. Tap mirror switch (3b) to choose color temperature and hold to dim up and down

Note : Ideal distance of drill holes for mirror installation

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196 W: kuzcolighting.com
20240109

References

• Kuzco Lighting – Modern Contemporary Lighting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>