Kuzco Lighting VL62248 LED Vanity Light Installation Guide

Kuzco Lighting VL62248 LED Vanity Light

Product Information

Specifications:

• Model: VL62248
• Type: LED Vanity Light
• Installation Types: Octagon Junction Box Install, Single Gang Box Install
• Manufacturer: Kuzco Lighting

Product Usage Instructions

Octagon Junction Box Install:

1. Remove the fixture from its original package.
2. Separate mounting plate from canopy and backplate by removing screws.
3. Attach mounting plate to the electrical junction box using provided screws.
4. Make proper electrical connections (black to hot L, white to neutral N, ground to GND) with provided wire nuts.
5. Attach canopy, followed by backplate to mounting plate. Attach fixture to backplate and canopy assembly and adjust as necessary and secure with fixture screws.

Single Gang Box Install:

1. Remove the fixture from its original packaging.
2. Remove the backplate from within the fixture by removing fixture screws.
3. Make proper electrical connections (black to hot L, white to\ neutral N, ground to GND) with provided wire nuts.
4. Attach the backplate to the single gang box using provided screws. Secure backplate to mounting surface with anchors and screws.
5. Attach fixture to the backplate and adjust as necessary and secure with fixture screws.

Frequently Asked Questions (FAQ)

Q: What should I do if the light is not turning on after installation?
A: Double-check all electrical connections and ensure they are properly secured. If the issue persists, contact technical support for assistance.

Q: Can this LED Vanity Light be dimmed?
A: Please refer to the product specifications or consult the manufacturer to determine if this specific model is dimmable.

START FROM HERE

• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference

Please Note:

• This Kuzco LED fixture comes with pre-wired LED module(s).
• Unless instructed to do so, please do not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage.
• For dimming, an ELV (Electronic Low Voltage) type of dimmer is required.
• 120V input

INSTRUCTION

(Octagon junction box install)

1. Remove fixture from its original package
2. Separate mounting plate (1c) from canopy (2a) and backplate (2b) by removing screws (1d)
3. Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package
4. Make proper electrical connections (black to hot “L”,white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package
5. Attach canopy (2a), followed by backplate (2b) to mounting plate (1c) with screws (1d). Attach fixture (3a) to backplate and canopy assembly (2a/2b) and adjust as necessary and secure with fixture screws (3b)

(Single gang box install)

1. Remove the fixture from its original packaging. Remove the backplate (2b) from within the fixture (3a) by removing fixture screws (3b). Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package. Attach the backplate (2b) to the single gang box (1a), using screws (1d) provided in the hardware package. Secure backplate (2b) to mounting surface with anchors (1f) and screws (1g)
2. Attach fixture (3a) to the backplate ((2b) and adjust as neccessary and secure with fixture screws (3b)

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
20240109

References

• Kuzco Lighting – Modern Contemporary Lighting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>