KUZCO CF91954 Thalia Ceiling Fan Instruction Manual

KUZCO CF91954 Thalia Ceiling Fan

SAFETY INFORMATION

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. CAUTION : Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.
4. WARNING : To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed control device.
5. WARNING : To reduce the risk of fire, electric shock, or personal injury, mount to UL Listed outlet box marked “acceptable for fan support of 15.9 kg (35 lbs) or less” and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of light fixtures are not acceptable for fan support and may need to be replaced. Due to the complexity of the installation of this fan, a qualified licensed electrician is strongly recommended.
6. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 50 pounds.
7. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor. The tip of the fan blade to the nearest wall/obstruction: 30 inches.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
11. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment- grounding conductor on one side of the outlet box.
12. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL and cUL Listed and marked suitable for use with the model fan you are installing. Switches must be UL and cUL General Use Switches. Refer to the Instructions packaged with the light kits and switches for proper assembly.
13. Note : Suitable for use in damp locations. Use only with light kits marked “Suitable for use in damp locations.”
14. Do not operate reversing switch while fan blades are in motion. Fan must be turned off and blades stopped before reversing blade direction.

WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH AN ISOLATING WALL SWITCH.
WARNING : TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN INSTALLING THE BRACKETS, BALANCING THE BLADES OR CLEANING THE FAN.

TOOLS NEEDED

• Phillips screwdriver
• Flathead screwdriver
• Step ladder
• Wire cutter

HARDWARE INCLUDED

• Bracket Mounting Hardware
  • wood screws (1a)
  • screws (1b)
  • wire nuts (1c)
  • lock washers (1d)
  • flat washers (1e)
• Blade to Motor Screws and Lock Washers (2a)
• Balance Kit (3a)
• Fan Mounting Hardware
  • cotter pin (4a)
  • clevis pin (4b)

PACKAGE CONTENTS

PREPARING THE MOUNTING HARDWARE

Outlet Box Mounting Options
If there isn’t an existing UL Listed octagonal mounting box marked “Acceptable for Fan Support” follow the instructions below.
( REMINDER : an electrical junction box for use with luminaires is not acceptable for this application)

• Before you begin installing the mounting box, shut off the power at the circuit breaker of the fuse box.
• Secure the box directly to the building structure. The figures below show 3 example methods.

INSTALLING THE HANGING BRACKET

CAUTION : TO AVOID POSSIBLE ELECTRICAL SHOCK, BE SURE ELECTRICITY IS TURNED OFF AT THE MAIN POWER BOX BEFORE WIRING. ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES AND THE CEILING FAN MUST BE GROUNDED AS A PRECAUTION AGAINST POSSIBLE ELECTRIC SHOCK.

1. Loosen the two mounting screws in the outlet box. Pass the 120-Volt supply wires through the center hole in the slide-on mounting bracket.
2. Slide the slide-on mounting bracket on to the mounting screws and center the slide-on mounting bracket in relation to the outlet box. If necessary, use leveling washers (not included) between the slide-on mounting bracket and the outlet box. The flat side of the slide-on mounting bracket should face toward the outlet box, as shown.
3. Securely tighten the two mounting screws.

INSTALLING THE BLADES

1. Insert the blade through the slot cut-off in the center flywheel, align the three screw holes in the blade with the screw holes in the flywheel and secure with the screws and lockwasher provided.
2. Repeat for the remaining blades.

PREPARING THE MOTOR

1. Loosen the collar set screws from the motor collar.
2. Take out the set screw located in the hanger ball, lower the hanger ball and remove the cross pin. Remove the hanger ball from the hanger ball/downrod assembly.

ASSEMBLING THE FAN

WARNING : Failure to properly install the cotter pin could result in the fan becoming loose and possibly falling.

1. Carefully feed the motor wires and safety cable up through the downrod. Thread the downrod into the collar until the holes at the bottom of the downrod align with the holes in the collar.
2. Carefully insert the clevis pin through the holes in the collar and downrod. Insert the cotter pin through the hole, near the end of clevis pin until it snaps into its locked position.
3. Slip the coupling cover, the canopy screw cover, and the canopy onto the downrod.
4. Carefully reinstall the hanger ball onto the downrod. Being sure that the cross pin is in the correct position, the set screw is tightened and wires are not twisted.

HANGING THE FAN

WARNING : The tab in the ring must rest in the groove of the hanger ball/downrod assembly. Failure to properly seat the tab in the groove could cause damage to the wiring.

1. Carefully lift the fan motor assembly up to the mounting bracket and seat the hanger ball/downrod assembly in the mounting bracket socket. Make sure the tab on the mounting bracket socket is properly seated in the groove in the hanger ball/downrod assembly. This will help to balance the ceiling fan.

INSTALLATION OF THE SAFETY CABLE SUPPORT

1. Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten). Slide the cable clamp onto the safety cable from the fan. Loop the safety cable around the wood screw that was just attached to ceiling joist. Feed the end of the cable into the clamp and pull as much cable through as possible. Firmly tighten screw in the clamp. Cut off excess cable.

INSTALLING THE RECEIVER

1. Position the house supply wires to one side of the slide-on mounting bracket; position the fan wires to the opposite side.

2. Insert the receiver (as shown, flat side toward ceiling) into the slide-on mounting bracket until it rests on top of the ball/downrod assembly.

ELECTRICAL CONNECTIONS

WARNING : To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before installation.
WARNING : Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.
CAUTION : To reduce the risk of electric shock, this fan must be installed with an isolating, general-use wall control/ switch.
NOTE : Control must be installed within 30 feet of fan.

1. Make wire connections from the fan to the receiver unit. For this step use the bundle of 3 wires on the receiver.
   • Connect the BLUE fan wire to the BLUE receiver wire.
   • Connect the BLACK fan wire to the BLACK receiver wire.
   • Connect the WHITE fan neutral wire to the WHITE receiver neutral wire.
2. Connect the wiring from the ceiling to the receiver unit. For this step use the bundle of 2 wires on the receiver. Secure with supplied wire nuts.
   • Connect the BLACK building supply wire to the BLACK receiver wire.
   • Connect the WHITE receiver neutral wire to the WHITE building neutral wire.
   • Connect the COPPER building ground wire to the 2 GREEN ground wires from the fan.

INSTALLING THE CANOPY

WARNING : When using the standard ball/downrod mounting, the tab in the ring at the bottom of the mounting bracket must rest in the groove of the hanger ball. Failure to properly seat the tab in the groove could cause damage to the wiring.
NOTE : The magnet is pre-attached on the canopy bottom cover for you to remove and install easily.

1. Align the locking slots of the canopy with the two screws and alignment post (in the slide-on mounting bracket).
2. Push up the canopy and turn it until the alignment post engages to the round hole and the screws engage to the key slots.
3. Firmly tighten the two mounting screws.
4. Align the oval shape on the canopy with canopy bottom cover.
5. Push up the canopy bottom cover until the screw heads engage to the slots on the canopy bottom cover so that the magnetic canopy bottom cover can be attached to the bottom of the canopy properly.

INSTALLING THE LIGHT KIT PAN

CAUTION : To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit.

1. Loosen but do not remove two of three mounting screws from the fan motor assembly; Remove one mounting screw.
2. Push the light kit pan up to the fan motor assembly so that the two loosened screw heads fit into the keyhole slots. Turn the light kit pan, tighten the screws.
3. Re-install the screw that was removed in step 1 and tighten firmly.

INSTALLING THE LED ASSEMBLY

CAUTION : To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit.

1. Remove one screw from the light kit pan and loosen, but do not remove, the other two screws.
2. Connect the wires from the light kit fitter assembly to the wires from the fan motor assembly by connecting the molded adaptor plugs together. Carefully tuck all wires and splices into the switch cap.
3. Push the light kit assembly up so that the two loosened screw heads fit into the keyhole slots.
4. Turn the light kit assembly, tighten the screws. Reinstall the screw that was removed in step 1 and tighten firmly.

INSTALLING THE GLASS SHADE

1. Place the glass shade into the light kit pan, aligning the three flat areas on the top of the glass shade with the three raised dimples in the light kit pan. Turn the glass shade until it stops.

INSTALLING THE REMOTE CONTROL HOLDER

1. Remove the remote control holder cover from the remote control holder.
2. Attach the remote control holder with the two remote control holder mounting screw provided.
3. Replace the remote control holder cover into remote control holder.

OPERATION

IMPORTANT : If you have two or more fans, please follow steps below to control each fan independently. Also follow steps below to re-pair the remote and the receiver when needed.

Install battery (included). To prevent damage to transmitter, remove the battery if not used for long periods of time.

1. 1, 2 and 3 buttons:
   These three buttons are used to set the fan speed as follows:

   • 1 = minimum speed
   • 2 = medium speed
   • 3 = high speed

2. Power button :
   This button turns the fan off.

3. Breeze button :
   This button turns on “breeze” option.

4. Light button :
   This button controls the light “ON/OFF” and “Dimmable” options.

5. 2H, 4h and 8H buttons:
   These three buttons are used to set the fan timer as follows:

   • 2H = 2 hour timer
   • 4H = 4 hour timer
   • 8H = 8 hour timer

SET code setting button:
Follow the below steps to set the remote control:

• With the fan’s power off, press and release the “Learn” button located in the remote’s battery compartment within 30 seconds of turning the electrical power to the fan on. If pairing is successful, the fan’s light kit will flash, the blades will begin to spin and the fan and light kit will turn off within 30 seconds.

NOTE : If the self calibration test failed, turn the AC power off; restore power and process the self calibration test again.
NOTE : The learning frequency function and self calibration test will continue to retain the last set frequency and calibration set even when the AC power is shut off. If the frequency is changed the self calibration test will occur again

Summer Mode and Winter Mode Operation
The fan shipped from the factory with the reversing switch positioned to circulate air downward. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning, then slide the reversing switch (located at the top of the motor housing, refer to page 7) to opposite position, and turn fan on again. The fan blades will turn in the opposite direction and reverse airflow.

Speed settings for warm or cold weather depend on factors such as room size, ceiling height and number of fans.

OPERATING CEILING FAN WITH THE BOND APP

1. Download the BOND HOME app

   • Using your smart device, navigate to the application store (Apple App Store or Google Play). Download the free BOND Home app and create an account.

2. Connect to the BOND receiver
   NOTE : Confirm that your smart device (phone/tablet) is connected to your WiFi network before proceeding.

   • Ensure the fan and receiver are receiving power from the house supply by using the remote control to turn the fan and light on and off.
   • Open the BOND Home app on your smart device and follow the instructions included in the app to add your fan.

CARE AND CLEANING

• Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges.
• When dusting the blades, you must support the blade to prevent bending – no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.

TROUBLESHOOTING

when pushing a button, it is
| | not transmitting a signal. Please check battery, power to wall control/circuit breaker and all
| ****

3.

| electrical connections.

Assure there are no more than 2 fans operating on a circuit through the wall control. Assure that

| | there are no more than 12 fans operating on a circuit through an on/off wall switch or a breaker
| ****

4.

| (not through a wall control).

Assure that the fan is within range of the wall control (30 ft.).

FAN SOUNDS NOISY| 1.| Allow a 24-hour “breaking-in” period. Most noise associated with a new fan will disappear during
| ****

2.

| this time.

Make sure all motor housing screws are securely fastened.

| 3.| Make sure the screws that attach the fan blade to the fan are tight.
| 4.| Make sure your ceiling box is secure and rubber isolator pads are used between the mounting
| | bracket and outlet box.
FAN WOBBLES| 1.| Check that all blade to motor and blade arm screws are secure.
| 2.| If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
| ****

3.

| redistribute the weight and possibly result in smoother operation.

Make sure the mounting plate is securely fastened to the ceiling outlet box.

| 4.| Make sure ceiling box is secure.

KUZCO GROUP CEILING FAN LIFETIME LIMITED WARRANTY

Kuzco Group products are warranted against defects in materials and construction, subject to conditions and exclusions, for a period of one (1) year from the date of product shipment to the customer. Kuzco Group warrants the original owner that the motor in the fan will be free from defects for the lifetime of the fan. This warranty does not apply to fans which have been damage because of improper installation, removed from the original installation or subjected to use for which the fan was not designed. The customer is responsible for any cost of removing the old fan, installing a new fan or any other costs. This limited lifetime warranty is in lieu of all other expressed warranties. Kuzco Group shall not be liable for any incidental or consequential damages.

Below is a detailed list of items warranted:

What is covered?

• Parts that arrive damaged
• Parts missing from the box
• Parts that do not function properly
• Parts that have ceased proper functioning within warranty limits

Wha t is not covered?

• Installation costs
• Parts worn down with regular usage
• Parts damaged in installation
• Modified parts
• Parts out of warranty

WARRANTY APPLIES ONLY TO ORIGINAL PURCHASER FROM AN AUTHORIZED KUZCO GROUP DISTRIBUTOR.

How to Activate your Smart Fan on a Android device

Step 1: Using your smart device, scan the QR code below to go to the application Store to download the free Bond Home app.

Step 2: Check that your fan and receiver are securely connected to the house supply: Using your fan’s remote control, turn the fan and the light on and off.

Step 3: Open the Bond Home App on your mobile device and follow the step- by-step instructions in the app to add your ceiling fan.

• Create an account or login to your existing account.
• You will be prompted to allow permissions to the Bond Home App. These permissions are needed to set up new devices.
• Select “+” to add a new device In the bottom
• Select the “Smart by Bond” ceiling fan option

Step 4: Follow the prompt to go to your device’s settings
If you do not see the Bond Config Wi-Fi network listed, press and hold the power button on your ceiling fan’s remote control for 10 seconds. Additionally, you can try refreshing your Wi-Fi list. Go back to the Bond Home app.

Step 5: A Confirmation will appear on-screen to let you know that your ceiling fan has been successfully connected to the Bond Home App. Click CONTINUE to proceed with setting up your ceiling fan.

Step 6: Test your ceiling fan according to the app’s prompts to toggle the fan and lights.

Step 7: Name your ceiling fan:

• Choose a location from the predefined list add your own location.
• Choose a device name.
• This name will be used for integrations and voice commands, so we recommend choosing a simple and descriptive name.

Step 8:

Connect to Wi-Fi:

• Select your desired Wi-Fi network and enter password if necessary.
• Once the connection is made, select DONE. If your fan does not appear, try swiping down to refresh.

Step 9: Setup complete! Your fan should appear in the app. Sit back, relax, and enjoy your new ceiling fan!

If you need assistance at any time during the setup process, please visit the Help section of the Bond Home App, located in Settings. Select from either “Open a Ticket” or “Live Chat” to connect
with a member of the Bond Support Team.

How to Activate your Smart Fan on a iOS device

Step 1: Using your smart device, scan the QR code below to go to the application Store to download the free Bond Home app.

Step 2: Check that your fan and receiver are securely connected to the house supply: Using your fan’s remote control, turn the fan and the light on and off.

Step 3: Open the Bond Home App on your mobile device and follow the step- by-step instructions in the app to add your ceiling fan.

• Create an account or login to your existing account.
• You will be prompted to allow permissions to the Bond Home App. These permissions are needed to set up new devices.
• Select “+” to add a new device In the top-right corner
• Select the “Smart by Bond” ceiling fan option.

Step 4: Follow the prompt to go to your device’s settings and connect to the bond config Wi-Fi network. If you do not see the Bond Config Wi-Fi network listed, press and hold the power button on your ceiling fan’s remote control for 10 seconds. Additionally, you can try refreshing your Wi-Fi list. Go back to the Bond Home app.

Step 5: A confirmation will appear on-screen to let you know that yourceiling fan has been successfully connected to the Bond Home App. Click CONTINUE to proceed with setting up your ceiling fan.

Step 6: Test your ceiling fan according to the app’s prompts to toggle the fan and lights.

Step 7: Name your ceiling fan:

• Choose a location from the predefined list or add your own location.
• Choose a device name. This name will be used for integrations and voice commands, so we recommend choosing a simple and descriptive name.

Step 8: Connect to Wi-Fi:

• Select your desired Wi-Fi network and enter password if necessary.
• Once the connection is made, select DONE. If your fan does not appear, try swiping down to refresh

Step 9: Setup complete! Your fan should appear in the app. Sit back, relax, and enjoy your new ceiling fan!

If you need assistance at any time during the setup process, please visit the Help section of the Bond Home App, located in Settings. Select from either “Open a Ticket” or “Live Chat” to connect with a member of the Bond Support Team.

Troubleshooting

To perform a Factory Reset:
The Factory Reset will erase all fan settings, schedules, and disconnect from your Wi-Fi network. However, the fan will remain paired with the remote control.

1. Turn off the breaker or wall switch.
2. Turn the breaker/switch back on.
3. Immediately press and hold the Fan Speed 1 button on your ceiling fan’s remote control for 20 seconds, or until the ceiling fan light flashes five times.
   ( Note: You must start holding the  button within 15 seconds of turning the breaker or wall switch back on.)

FAN SLOPE CEILING ADAPTOR ACCESSORY

1. Install mounting plate to outlet box in ceiling using the screws and washers provided with your outlet box. Remove the two canopy mounting screws 180 degrees apart on outside edge of mounting plate. Loosen the two remaining screws. This will make the installation of the canopy easier in Step 5 and 6 (Fig 1).
2. Remove the downrod ball that was supplied with your ceiling fan by loosening the set screw. Slide the downrod ball off the downrod. Be sure to keep the crosspin supplied with your fans downrod to use with the slope ceiling adaptor ball (Fig 2).
3. Install the slope ceiling adaptor ball to the existing downrod or new longer downrod with the crosspin from your existing downrod. Push ball up until it engages the crosspin and tighten set screws (Fig 3).
4. Feed motor lead wires through downrod/canopy assembly and insert downrod into motor yoke. Make sure that the tab in the canopy engages the notch in the downrod ball. Install downrod to fan using instructions provided with your fan as this may vary from model to model (Fig 4).
5. Carefully hang fan onto hook in mounting plate using one of the two holes in the canopy. This will allow hands-free wiring. Refer to your ceiling fan owners manual for wiring instructions (Fig 5)
6. Carefully lift fan from mounting plate hook, making sure not to break any wire connections. The canopy has two mating slots and two mating holes. Position both slots in canopy directly under and in line with two mounting plate screws and lock washers. Lift fan until mounting plate screws are seated in bottom of slots in canopy (Fig 6).
7. Rotate canopy clockwise until both mounting screws drop into slot recesses. Tighten screws securely. Install third and fourth screws with lock washers into mating holes and tighten (Fig 6).

FAN DOWNROD ACCESSORY INSTALLATION SHEET

MODEL :

• X-RD34-12 FAN
• X-RD34-18 FAN
• X-RD34-24 FAN
• X-RD34-36 FAN
• X-RD34-48 FAN
• X-RD34-60 FAN

FAN DOWNROD ACCESSORY

1. Remove the hanger ball that was supplied with your ceiling fan by loosening the set screw. Slide the hanger ball off the original downrod.
2. Carefully feed the motor wires and safety cable up through the new downrod. Thread the new downrod into the collar.
3. Align the holes and replace the clevis pin and cotter pin. Tighten the two collar set screws.
4. Slip the coupling cover, the canopy screw cover, and the canopy onto the new downrod.
5. Carefully reinstall the hanger ball onto the new downrod. Being sure that the cross pin is in the correct position, the set screw is tightened and wires are not twisted.
6. Refer to specific model ceiling fan installation instructions to install ceiling fan.

References

• Kuzco Lighting – Modern Contemporary Lighting.
• Fan Resources – Kuzco Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>