KUZCO LP90748 Poplar LED Black Linear Pendant Ceiling Light Installation Guide

KUZCO LP90748 Poplar LED Black Linear Pendant Ceiling Light

START FROM HERE

•  Make sure the power is completely off at the fuse box.
•  Have your fixture installed by a qualified licensed electrician
•  Prepare everything in a clear area.
•  Wear gloves at all times during this installation.
•  Read the instructions carefully before you start assembly.
•  Keep this instruction sheet for future reference.

Please Note

•  This Kuzco LED fixture comes with a pre-wired LED module(s).
•  Unless instructed to do so, please do not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage.
•  For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required.
•  120V input

Technical Support: 1-855-855-8926

1. Remove the fixture from its original packaging

2. Separate the mounting plate (1c) from the canopy (2a) by removing the screws (2c) with the Allen key provided

3. Attach the mounting plate (1c) to the electrical junction box (1a) using the two screws (1d) provided in the hardware package

4.  Thread connector (4b) into the fixture (4a) to secure

5. Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in the hardware package

6. Attach canopy (2a) to mounting plate (1c) with screws (2c) and Allen key provided
   Mark and install aircraft barrel (3b) with screw (3a) and plastic anchor (3c) to the ceiling, opening on aircraft barrel (3b) facing towards canopy (2a). The ideal distance between ceiling anchors (3b) is 41-5/8”

7. Place wire onto pulley (3g), insert into ceiling anchor (3b), and secure with screw (3f) using the Allen key

8. Fine tone wire length if necessary, by push and hold wire gripper (2b) and then adjust the wire to the desired length

START FROM HERE

•  Make sure the power is completely off at the fuse box.
•  Have your fixture installed by a qualified licensed electrician
•  Prepare everything in a clear area.
•  Wear gloves at all times during this installation.
• Read the instructions carefully before you start assembly.
•  Keep this instruction sheet for future reference.

Please Note

•  This Kuzco LED fixture comes with a pre-wired LED module(s).
•  Unless instructed to do so, please do not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage.
•  For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required.
•  120V input

FOR ALTERNATIVE SIDE CANOPY INSTALL

1. Disconnect output wires on the driver (2f)
2. Move wire gripper (2b) to the bottom of the canopy, secure with nut (2g), and close holes on side of the canopy with plugs (2e)
3. Thread connector (4b) into the fixture (4a) to secure
4. Reconnect the driver’s positive wire to the center core of the hanging cable, and negative to meshed conductor
5.  Attach canopy (2a) to mounting plate (1c) with screws (2c) and Allen key provided. Position desired amount of wire by pushing gripper (2b) on the canopy
6. Add plastic anchors (4e) to the ceiling and wood backing and secure aircraft cable barrels (4f) to it with screws (4d) and close with wire gripper (2b)
7. Fine tone wire length if necessary, by push and hold wire gripper (2b) and then adjust the wire to the desired length

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196 W: kuzcolighting.com 2021040120210401

References

• Kuzco Lighting – Modern Contemporary Lighting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>