QSFPTEK S5310-48P6X Stackable 48 Port Gigabit Ethernet User Guide

**QSFPTEK S5310-48P6X Stackable 48 Port Gigabit Ethernet User Guide

**

Introduction

The QSFPTEK S5310-48P6X has 48x 10/100/1000BASE-T ports supporting IEEE 802.3af/at(30w max) for powering attached wireless access points, IP cameras, or other POE and POE+ standard terminal devices. And 6x 10GE SFP+ uplinks enable establish up to 60 Gbps links with the aggregation layer switch. It supports stacking up to eight S5300 series switches, making them logically regarded as one for interconnection and management.

We appreciate your decision to select S5310-48P6X. This manual is intended to help you become acquainted with the switch design and provide instructions for implementing the switches into your network.

Accessories

• Power Cord x1

• Console Cable x1

• Mounting Bracket x2

• M3 Screw x6

• Rubber Pad x4

Hardware Overview

Front Panel Ports

Front Panel LEDs

Back Panel

Installation Requirements

Tools Preparation

• Screwdriver
• Static-proof wristband
• Bolt
• Ethernet cable
• Other Ethernet terminal devices
• Control terminal

Safety Principles

The safety notices mentioned here means that improper operation may lead to body damage

• Read the installation guide carefully before you operate the system.
• Only professionals are allowed to install or replace the switch.
• Pull out the AC power socket before operating on the machine box or working beside the power source.
• The final configuration of products must comply with relative national laws and regulations.

Site Environment

• Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is provided for device cooling.
• Avoid to damage devices by following the electrostatic discharge prevention procedure.
• Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed because the opened machine box will reverse the cool air flow.

Mounting the Switch

Connecting the Power

1. Plug the AC power cord to the switch power port on the back rear
2. Connect the other end of the power cord to a AC power source equipment.

Connecting the RJ45 Port

1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
2. Connect the other end of the Ethernet cable to the switch RJ45 port.

Connecting the SFP+ Port

1. Insert the SFP+ module into the SFP+ port.
2. Plug a fiber patch cable to the SFP+ transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.

Connecting the Management Ports

Connecting the Console Port

1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.

Configuring the Switch

Configuring the Switch Using the Web-based Interface

Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser
Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any number from 2 to 254) and the subnet mask to 255.255.255.0.

Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.

Configuring the Switch Using the Console Port

Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.

Step 4: Enter the default username and password (admin/admin).

Troubleshooting

Hardware Fault Analysis
Power and cooling systems— power and fan
Port,   cable and connection—ports on the front panel of the switch and the cables connecting these ports

Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:

1. When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
2. If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3
3. Requirements for Common Locations”.
4. If the switch cannot be started and the PWR indicator is off, check the power

Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:

If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.

If the power on-off is at the “ON” location, check the power source and the power cable.
If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.

Support and Other Resources

• Contact us https://www.qsfptek.com/company/contact-us.html
• Email sales@qsfptek.com
• Customer Success https://www.qsfptek.com/resources/customer-success-stories

Product Warranty

S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or e -xchange of your items within 14 days of receiving them.

For more details about applying qualifications, please live chat or email sales@qsfptek.com for support

5 Years Warranty

30-days Return W

www.qsfptek.com

S5310-48P6X Quick Start Guide
48-Port Gigabit Ethernet L3 PoE+ Switch
48x PoE+ Ports@740w , with 6x 10GE SFP+ uplink, Support Stacking

References

• QSFPTEK - Compatible Optical Transceivers Factory Outlet
• Customer Success Stories - QSFPTEK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>