KUZCO LP90404-UB LED Linear Pendant Mason Installation Guide

Table of Contents

KUZCO-LP90404-UB-LED-Linear-Pendant-Mason-PRO

Specifications:

Step 1: Preparation

Remove the fixture from its original package.
Attach the strap plate (3c) to the base plate (3d) using screws (3b) after pulling the strap (6a) through.

Step 2: Mounting

Mount the inner ceiling barrel (4b) to the mounting surface with the anchor (4a) and screw (4c).
Attach the outer ceiling barrel (4d) to the inner ceiling barrel (4b) with screws (4e).
Pull the strap (6a) to the desired length, cut off any excess, and loop it through the buckle (4g) on the non-power side. Secure with a screw (4f).

Step 3: Assembling Pendant

Pull the strap (6a) through the pendant cap (5a) and loop it around the strap disc (5c).
Secure the disc (5c) to the pendant (5d) with screws (5b), followed by attaching the pendant cap (5a) to close.

Step 4: Electrical Connections

Make proper electrical connections – black to hot L, white to neutral N, ground to GND – using wire nuts (1b) provided in the hardware package.

Step 5: Final Installation

Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws provided in the hardware package.
Secure the canopy (2a) to the base plate (3d).

Frequently Asked Questions (FAQ):

Q: What should I do if I encounter flickering lights after installation?
A: Flickering lights can be caused by improper electrical connections. Double- check all connections and ensure they are secure and correctly matched (black to hot L, white to neutral N, ground to GND).
Q: Can I adjust the length of the pendant?
A: Yes, you can adjust the length of the pendant by pulling the strap to your desired length and cutting off any excess before securing it with a screw.

START FROM HERE:

Make sure POWER is COMPLETELY OFF at the fuse box
Have your fixture installed by a qualified licensed electrician
Prepare everything in a clear area
Wear gloves at all times during this installation
Read instructions carefully before you start assembly
Keep this installation sheet for future reference
Technical Support: 1-855-855-8926

Please Note:

This Kuzco LED fixture comes with pre-wired LED module(s)
Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required
120V input

Remove fixture from its original package
Attach strap plate (3c) to base plate (3d) with screws (3b) after pulling strap (6a) through. Attach mounting plate (1c) base plate (3d) with screws (3a) (See Illustration 2)
Mount inner ceiling barrel (4b) to mounting surface with anchor (4a) and screw (4c). Attach outer ceiling barrel (4d) to inner ceiling barrel (4b) with screws (4e). Pull strap (6a) to desired length and cut off any unwanted length and loop it through buckle (4g) on non-power side. Secure with screw (4f) (See Illustration 3)
Pull strap (6a) through pendant cap (5a) and loop it around strap disc (5c). Secure disc (5c) to pendant (5d) with screws (5b), followed by pendant cap (5a) to close (See Illustration 4)
Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package
Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package. Secure canopy (2a) to base plate (3d) (See Illustration 1)

KUZCO-LP90404-UB-LED-Linear-Pendant-Mason-1