Immax 07229L Neo Pinna LED Wall Lamp Installation Guide
- June 16, 2024
- immax
Table of Contents
Installation manual for wall lamp
Immax NEO PINNA 80cm 34W 2378lm black Zigbee3.0
07229L Neo Pinna LED Wall Lamp
The
technical parameters for a given model can be found on the label on the
package or on the website www.immax.eu under the
catalogue number of the product.
ASSEMBLY INSTRUCTIONS
a) Switch off the fuses before installing the luminaire.
b) A minimum of 2 people is required to safely install this product.
c) Electrical installation work may only be carried out by a qualified worker.
d) Unpack the luminaire from the packaging and lay the luminaire on a soft
surface
e) If you have made sure that the electricity is safely switched off, you can
start the installation of the luminaire itself. When mounting, follow the
enclosed original pictorial instructions from the manufacturer.
f) Improper installation or manipulation of the luminaire will void the
luminaire warranty
A. Only for the light with diffuser: Diffuser installation:
When installing the diffuser or removing the plastic diffuser from the
luminaire, please take extra care! Increased contact can damage the surface
finish of the luminaire or diffuser. This mechanical damage is not covered by
the warranty! Thank you for understanding.
B. only for PENDANT LIGHT
Final adjustment to the height of the hanging
chandelier: First, install the hanging chandelier on the ceiling, according to
the instructions above. For the final adjustment of the height of the hanging
chandelier, it is sufficient to adjust the length of the suspension cables.
Shortening the cable length: release the lock and slowly slide the cables
upwards towards the base of the hanging chandelier. The cable will then remain
fixed in the position you have selected.
Extending the cable length: if you have installed the hanging chandelier cable
too high, you must first release it by releasing the lock (located inside the
luminaire base) at the upper end of the cable. This will allow the cable to be
released and then adjusted to the position of your choice. You may then adjust
all cables one by one. Thank you for understanding
C. Maintenance:
Construction doesn´t need any special maintenance. Use only wet or dry cloth
to wipe the surface of the light unit.
D. PAIRING – to pair the luminaire with the remote control, see the
manual in the remote control.
If the luminaire cannot be paired with the remote control, reset both the
remote control and the luminaire. Only then try pairing the luminaire with the
remote control again.
E. PAIRING MODE – the luminaire is in pairing mode for 30 seconds after
switching on
F. LAMP RESET – reset the luminaire only if the luminaire cannot be
paired with a gate or remote control.
LAMP RESET:
a) ON – 1s – OFF 2s
b) ON – 1s – OFF 2s
c) ON – 1s – OFF 2s
d) ON = 1s – OFF 2s
e) ON – the lamp flashes for 5 seconds
f) then confirm the reset – OFF 2 seconds – ON
HELP: point a) to d) ON-OFF in rhythm of the first letter of morse code ;
‘alpha’.
USER MANUAL
Manufacturer and importer:
IMMAX, Pohoří 703, 742 85 Vřesina, EU |
www.immaxneo.cz |
www.immaxneo.com
Made in P.R.C.
Immax NEO Smart remote v2 Zigbee 3.0
LIGHTING DEVICES CONTROL VIA APP
- When initially power on the Lighting device:
– Lighting Device will start breathing smoothly in cold white color, and wait to be connected to Gateway via App (During this breathing time, Lighting device can NOT be paired directly to the remote).
– After been successfully connected to Gateway, Light will stay in steady cold white and brighter. Now user can use app to control the Light normally!
LIGHTING DEVICES CONTROL VIA REMOTE
Connecting Process:
We provide 3 flexible methods for consumers to use Remote to control Light(s).
Below Method A and Method B is when user ALREADY add the Light into app.
Method X is for those Light(s) which has NOT been added to App.
METHOD A (ONLINE PAIRING MODE)
Step 1: On the remote control, long press the “ON” and “OFF” buttons
simultaneously for 5 seconds, the LED indicator of the remote control will
start to flash slowly.
Step 2: In the Immax NEO PRO app, under the Home tab, click “+” to select the
option to add a new product. Select the remote control from the list of
devices. Then follow the instructions in the app.
Step 3: Then open the remote tab in the app and click on the icon on the top
right – assign lights to the remote.
Step 4: Press “+” and “-” on the remote at the same time, the LED indicator
will flash.
METHOD B (OFFLINE PAIRING MODE)
Put the remote VERY close to the bulb and long press “ON” button of the remote
until Light breath for 3 times. Then the light will be removed in the gateway
and link directly to the remote.
Note: Method B can only pair ONE Light at a time, and can maximumly connect
and control 30 lights.
– Method X (No App connected): Before you try Method X, please make sure the
Light NOT in continuously breathing status.
We can always use Remote to connect to Light by long pressing “ON”button until
it breath for 3 times.
CONTROL PROCESS
Please see below snapshot of 4 simple functions that our remote now supported
after you connected the Light to the Remote.
DISCONNECT PROCESS
- If user previously used Method A and already added both Remote and Lights to the App, then user can directly edit to delete the light in the Remote page.
- If user previously used Method B or Method X for connecting, Then he need to put the Remote very close to the Light and long press “OFF”button until Light breath smoothly for 3 times, which proves disconnecting completed.
DOWNLOAD THE IMMAX NEO PRO APPLICATION
https://smartapp.tuya.com/immaxneosmart
Vyrobce / Dovozce: IMMAX, Pohori 703, 742 85 Vresina, EU
www.immax.cz | www.immax.eu |
Vyrobeno v PRC
Manufacturer and importer:
IMMAX, Pohori 703, 742 85 Vresina, EU
www.immaxneo.cz |
www.immaxneo.com
Made in P.R.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>