KUZCO VM40432-5CCT LED Vanity Mirror Instruction Manual

: June 16, 2024
: KUZCO

Table of Contents

KUZCO VM40432-5CCT LED Vanity Mirror
Product Usage Instructions:
LED Vanity Mirror VM40432
INSTALLATION SHEET
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KUZCO VM40432-5CCT LED Vanity Mirror

LED Vanity Mirror

Specifications

Model : VM40432
Dimensions : 6-1/8″ x 6-1/8″
Color Temperature : Adjustable
Power Source : Electrical

Product Usage Instructions:

Remove mirror from its original package
Take the mirror out of its original packaging.

Mounting the wall bracket

Measure and mark the desired location for the wall bracket (2a).
Mount the bracket to the wall using screws (2c) and anchors (2b).
Make sure to attach the screws directly to a stud or structure.
Refer to Illustration 3 for the ideal distance measurement.

Electrical connections
Make the proper electrical connections. Connect the black wire to the hot L, the white wire to the neutral N, and the ground wire to GND. Use the wire nuts (1a) provided in the hardware package. Connect the other end of the wires to an ON/OFF wall switch (wall switch provided by others). Note that the wall switch must be used to ensure proper operation of the LED mirror.

Note
Failure to follow installation and/or operating instructions voids the warranty.

Securing the mirror
Bend both tabs of the wall bracket (2a) back to prevent the mirror from sliding side to side. Align the mirror’s mounting bracket (3a) with the wall bracket (2a) and secure them together. Refer to Illustration 1 for visual guidance.

Adjusting color temperature and dimming
Tap the mirror switch (3b) to choose the desired color temperature. Hold the switch to dim the mirror up and down.

Frequently Asked Questions:

Q: What is the ideal distance for drilling holes for mirror installation?
A: The ideal distance for drilling holes is shown in Illustration 3.
Q: Do I need to use the wall switch provided by others?
A: Yes, the wall ON/OFF switch must be used to ensure proper operation of the LED mirror.
Q: What happens if I don’t follow the installation and operating instructions?
A: Failure to follow the instructions voids the warranty, and the manufacturer will not be held responsible for any problems or product malfunction.
Q: How can I contact technical support?
A: For technical support, please call 1-855-855-8926.

LED Vanity Mirror VM40432

VM40432

INSTALLATION SHEET

START FROM HERE

Make sure POWER is COMPLETELY OFF at the fuse box
Have your mirror installed by a certified licensed electrician
Prepare everything in a clear area
Wear gloves at all times during this installation
Read instructions carefully before you start assembly
Keep this installation sheet for future reference

Important
The installer and/or user must read, understand and follow these instructions before installing the product. This product must be properly installed before it is used. If instructions are not followed, the manufacturer will not be held responsible for any problems or product malfunction. Failure to follow installation and/or operating instructions voids the warranty.

Technical Support : 1-855-855-8926

Please Note

This Kuzco LED mirror comes with pre-wired LED module(s)
Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
Touch Dimming
Do not use alcohol or solvents to clean the mirror
For your convenience, assembly by two people is a must

Remove mirror from its original package
Measure, mark location of wall bracket (2a) location, mount to wall with screws (2c) and anchors (2b) (See Illustration 3 for ideal distance measurement) (Note: All screws must be attached directly to stud/structure)
Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1a) provided in hardware package to ON/OFF wall switch (wall switch provided by others)
NOTE : Wall ON/OFF Switch must be used to ensure proper operation of LED mirror
Bend both wall bracket (2a) tabs back to prevent mirror from sliding side to side (See Illustration 2). Align mirror (3a) mounting bracket to wall bracket (2a) to secure (See Illustration 1)
Tap mirror switch (3b) to choose color temperature and hold to dim up and down