KUZCO EG64816 LED Exterior Garden Installation Guide

EG64816 LED Exterior Garden
Installation Guide

LED Exterior Garden

START FROM HERE

• Make sure the POWER is COMPLETELY OFF
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all times during this installation
• Read instructions carefully before you start the assembly
• Keep this installation sheet for future reference
  Technical Support: 1-855-855-8926

Please Note:

• This Kuzco LED fixture comes with pre-wired LED module(s)

• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
  contact with the module could cause permanent damage

• 12V input with Outdoor Rated Low Voltage Transformer (Transformer supplied by others)

• Non-Dimming

• For typical ground stake mounting

• Luminaires shall not be installed within 10 feet of the pool, spa, or fountain

1. Remove the fixture from its original package

2. Run fixture wire (1b) from the canopy (1a) through the mounting hole on top of the ground stake (3a)

3. Run transformer wire (provided by others) to the location of the intended install
   Note : the low-voltage wires are intended for shallow burial – less than 6 inches

4. Align fixture thread (1d) (Note: fixture thread (1d) is 1/2-14 NPT) with a hole on the mounting base (1f) and secure to ground stake (3a) by threading clockwise until it fits snuggly. Secure mounting base (1f) to fixture (1a) with set screws (2b) and Allen key

5. Fill outdoor-rated wire nuts (2a) with silicone sealant (not provided). Cut and strip fixture wires (1b) and connect to transformer wire using outdoor rated wire nuts (2a) provided (Illustration 1)
   Note : for multiple low-voltage garden light installations daisy-chain low-voltage wire to each fixture from a 12V transformer

6. Place stake (3a) in the desired position and insert it into the ground until the flange of the stake is flush with the ground

Hardscape Mounting

START FROM HERE

• Make sure the POWER is COMPLETELY OFF
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all times during this installation
• Read instructions carefully before you start the assembly
• Keep this installation sheet for future reference
  Technical Support: 1-855-855-8926

Please Note:

• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
• 12V input with Outdoor Rated Low Voltage Transformer (Transformer supplied by others)
• Non-Dimming
• Hardscape Mounting
• Luminaires shall not be installed within 10 feet of the pool, spa, or fountain

1. Remove the fixture from its original package

2. Drill holes in the hardwood and secure the mounting base (1f) with screws (not provided) (Illustration 2)

3. Run wire (1b) from the canopy (1a) and through the mounting hole on top of the ground

4. Fill outdoor-rated wire nuts (2a) with silicone sealant (not provided). Cut and strip fixture wires (1b) and connect to transformer wire using outdoor rated wire nuts (2a) provided (Illustration 1)
   Note : for multiple low-voltage garden light installation daisy-chain low-voltage wire to each fixture from a 12V transformer

5. Secure canopy (1a) to mounting base (1f) with set screw (2b) and Allen key provided
   

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO
F: 604 538 7196
W:kuzcolighting.com
20210427

Documents / Resources

| KUZCO EG64816 LED Exterior Garden [pdf] Installation Guide
EG64816 LED Exterior Garden, EG64816, LED Exterior Garden, Exterior Garden, Garden LED, Exterior LED, LED
---|---

References

• Kuzco Lighting – Modern Contemporary Lighting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>