THE GALLEY IWA 30S Series DryDock 12 in stock Instruction Manual

THE GALLEY IWA 30S Series DryDock 12 in stock

Product Information

Specifications

• Model: IWA-30-S-DD-12-S-WA
• Material: American Black Walnut / Graphite Resin+
• Basin: KSO-30-S-DS-12-S-SS
• Stainless Steel: 16GA 316L
• Indoor/Outdoor: Yes
• Sound Reduction Technology: SilentArmorTM
• Finish: Angel finish
• Design: Three-tier design
• Drain: Reversible side drain
• Warranty: Limited Lifetime Warranty
• Made in: USA
• Certifications: ASME A112.19.3/CSA B45.4 certified, cUPCTM certified

Product Usage Instructions

Installation
To install the product, follow these steps:

1. Measure and mark the desired location for the product.
2. Cut out the countertop according to the provided dimensions.
3. Install a support cleat lower than the top of the cabinet by 1/16 inch (2mm).
4. Ensure a minimum of 2 1/8 inch (54mm) height clearance below the countertop.
5. Refer to the DWG and DXF templates available on TheGalley.com/specification-library for detailed installation instructions.

Customization
You can customize your galley by adding various accessories:

• Add 7-12 length
• Add 1-6 length
• Add 18 DryDock
• Add 12 DryDock
• Add Apron front

Maintenance
To keep the product in good condition, follow these maintenance tips:

• Use stainless steel clean + polish to clean the surface.
• Use wood condition + protection to maintain the wood components.
• Apply wood finishing balm for additional protection and shine.

FAQ

• Q: What is the warranty for the product?
  A: The product comes with a Limited Lifetime Warranty.

• Q: Can the product be used both indoors and outdoors?
  A: Yes, the product is suitable for both indoor and outdoor use.

• Q: Are there any certifications for the product?
  A: Yes, the product is ASME A112.19.3/CSA B45.4 certified and cUPCTM certified.

• Q: How can I contact customer care for additional assistance?
  A: You can contact The Galley’s Customer Care Department at 800.375.4255.

• Q: Where can I find templates for installation?
  A: DWG and DXF templates are available on TheGalley.com/specification-library.

Models

Specifications

Single Bowl

• Users: 1
• Wash Tools included: Four
• DryDock Tool included: One
• Galley BarTap® recommended: One
• Outside dimensions: 39 1/2” x 19 1/2” x 2 1/16”
• Interior dimensions: 38” x 17” x 2”
• Countertop cutout: 38 1/2” x 18”
• Minimum cabinet size: 42” or 107cm
• Minimum clearance required for DryDock below countertop: 2”
• DryDock location: Drain side (S)

Basin (KSO-30-S-DS-12-S-SS)

• 16GA 316L stainless steel indoor/outdoor
• SilentArmor™ sound reduction technology
• Angel finish
• Three tier design
• Star™ groove pattern
• Reversible side drain
• Drain cover included
• Limited Lifetime Warranty
• Made in the USA
• ASME A112.19.3/CSA B45.4 certified cUPC™ certified

Customize Your Galley

• Add 7-12” length
• Add 1-6” length
• Add 18″ DryDock
• Add 12″ DryDock
• Apron front
• 9” depth
• Center drain
• ThinTop™
• WorkTop™
• Color-coded labels available

Tools

Wash Tools included (WKT-4T)

DryDock Tool included (DR-12)

Upper Deck

Recommended Basin Accessories & citrine

Tap Hole Specifications

SUGGESTED GALLEY TAP PLACEMENT GUIDE

• Suggested maximum inside corner radius of countertop cutout 3/8”
• T. Galley BarTap® 1 3/8” min to 1 1/2″ max hole diameter
• Center Tap hole diameters 2” behind cutout
• Note: Galley Hot & Cold Tap requires a minimum 8″ clearance to the centre if installed to the right of the Galley Tap
• Note: Tap Placements are for right-hand or left-hand drain orientation

Call 800.375.4255 or email [email protected] for additional guidance on Tap and Tap Accessory placements.

Countertop Cutout Plan

STAINLESS STEEL COMPLIANCE ASME A112. 19.3-2008/CSA B45.4-08
WE RESERVE THE RIGHT TO MAKE REVISIONS WITHOUT NOTICE IN THE DESIGN OF PRODUCTS OR IN PACKAGING UNLESS THIS RIGHT HAS SPECIFICALLY BEEN WAIVED AT THE TIME THE ORDER IS ACCEPTED.

DWG and DXF templates are available on our website:
TheGalley.com/specification-library.

Tap Hole Specifications

SUGGESTED GALLEY TAP PLACEMENT GUIDE

• Suggested maximum inside corner radius of countertop cutout 3/8”
• T. Galley BarTap® 1 3/8” min to 1 1/2″ max hole diameter
• Center Tap hole diameters 2” behind cutout
• Note: Galley Hot & Cold Tap requires a minimum 8″ clearance to the centre if installed to the right of the Galley Tap
• Note: Tap Placements are for right-hand or left-hand drain orientation

Countertop Cutout Plan

STAINLESS STEEL COMPLIANCE ASME A112. 19.3-2008/CSA B45.4-08
WE RESERVE THE RIGHT TO MAKE REVISIONS WITHOUT NOTICE IN THE DESIGN OF PRODUCTS OR IN PACKAGING UNLESS THIS RIGHT HAS SPECIFICALLY BEEN WAIVED AT THE TIME THE ORDER IS ACCEPTED.

DWG and DXF templates are available on our website:
TheGalley.com/specification-library.

Questions

For additional assistance, please contact The Galley’s Customer Care Department at 800.375.4255

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>