signify ALKCO IB51999323 DCL LED Installation Guide

: June 16, 2024
: signify

Table of Contents

signify ALKCO IB51999323 DCL LED
Product Information
Product Usage Instructions
FAQ
Installation Instructions
WIRING
FCC STATEMENT
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

signify ALKCO IB51999323 DCL LED

Product Information

Specifications

Model Number: IB51999323
Brand: ALKCO
Installation: Must be performed by a qualified electrician
Power: Requires connection to a power source
Color: Black
Material: Housing Door, Lens
Dimensions: Not specified

Product Usage Instructions

Installation

Ensure installation is performed by a qualified electrician familiar with the product and its hazards.
Before installation or maintenance, make sure the power is OFF by disconnecting it at the fuse or circuit breaker.
Allow the fixture to cool down before handling or servicing.
Handle the product with care due to sharp edges.
If power tools are used during installation, exercise caution to avoid thread/gasket damage or lens breakage.
Failure to comply with these instructions may result in death, serious bodily injury, and property damage.

Thermal Protector Installation

Identify the thermal protectors on one side of the fixture as shown in Figure 3.1.
Remove the split ring bushing and discard it as shown in Figure 3.2.
Push the thermal protector into the hole until it snaps into place as shown in Figure 3.3.

FAQ

Q: Who should install this product?
A: Installation and maintenance of this product must be performed by a qualified electrician.
Q: What precautions should be taken during installation or maintenance?
A: Before starting installation or maintenance, ensure that the power is OFF by disconnecting it at the fuse or circuit breaker. Also, allow the fixture to cool down before handling or servicing.
Q: What should I do if I encounter sharp edges while handling the product?
A: Handle the product with care to avoid any risk of personal injury.
Q: Can power tools be used during installation?
A: Yes, power tools can be used, but it is important to be very careful. Uncontrolled torque settings may lead to thread/gasket damage or lens breakage.

WARNING

Risk of Fire, Electrical Shock, Cuts, or Other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed under the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at the fuse or circuit breaker.
Risk of Fire- Minimum 90°C supply conductors.
Risk of Burn- Disconnect power and allow a fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Must be very careful if power tools are used to install the fixture. Uncontrolled torque settings may lead to thread/gasket damage or lens breakage.
Failure to comply with these instructions may result in death, serious bodily injury, and property damage.

DISCLAIMER OF LIABILITY: ALKCO assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling, or use of this product.
IMPORTANT: Read carefully before installing the fixture. Retain for future reference.
NOTICE: These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, or to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for the user’s purpose, please contact your nearest representative.
NOTICE: Proper grounding is required to insure personal safety. Carefully observe the grounding procedure under the installation section.
NOTICE: The fixture may become damaged and/or unstable if not installed properly.
Note: Specifications and dimensions are subject to change without notice.
GENERAL: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier.
Compare the catalog description listed on the packing slip with the fixture label on the housing to ensure you have received the correct merchandise.

Installation Instructions

GRID INSTALLATION
Install the luminaire by placing it in the ceiling grid location as shown in Figures 1.1 and 1.2.

WIRING

Make supply connections through the access plate provided at the top of the luminaire. Wires are attached to the access plate for line (black), neutral (white), and ground (green) as shown in Figure 2.

Note: For fixtures with the LVC/LVD option, there will be additional wire connections required for the low-voltage controller function. The number of additional wire connections depends on the configuration of the luminaire (i.e., the number of circuits connected to the low-voltage controller). Wire colors could be a combination of the following: RED, BLUE, BLACK, and BROWN. For the LVC there will be a black & brown wire with no quick disconnect. For the LVD, all (4) colors may be present and will be identified as follows:

AMBIENT (Circuit A)
EXAM (Circuit B)
NIGHT LIGHT
READING LIGHT

The manufacturer spec sheet for each controller will be provided for additional explanation of the LVC/LVD functions.

THERMAL PROTECTOR INSTALLATION

Identify thermal protectors on one side of the fixture (Figure 3.1), remove split ring bushing and discard (Figure 3.2), and push thermal protector in the hole until it snaps into place (Figure 3.3).

FCC STATEMENT

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, according to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.