HALO HU30MSCTD09MB LED Undercabinet Light

Product Information

Specifications

• Model Number: IL51888423ML
• INS #: Classified

Product FAQ

• Q: Can the product be used in wet environments?
  • A: No, the product should be kept away from water sources to prevent damage.
• Q: Can I install the product on any surface?
  • A: The product should only be mounted on a structurally sound surface to ensure safety and stability.
• Q: Are the PIR and USB modules included with the product?
  • A: No, the PIR and USB modules are sold separately.

Packaging Contents

ITEMS REQUIRED

(Purchase separately)

• 2 Phillips screwdriver

• Safety glasses

Ordering Information

• 9 inch (22,8 cm) LED Undercabinet Light
  • HU30MSCTD09P (Plain White)
  • HU30MSCTD09MB (Matte Black)
• 18 inch (42,04 cm) LED Undercabinet Light
  • HU30MSCTD18P (Plain White)
  • HU30MSCTD18MB (Matte Black)
• 24 inch (60,9 cm) LED Undercabinet Light
  • HU30MSCTD24P (Plain White)
  • HU30MSCTD24MB (Matte Black)
• 36 inch (82,4 cm) LED Undercabinet Light
  • HU30MSCTD36P (Plain White)
  • HU30MSCTD36MB (Matte Black)
• 48 inch (119,8 cm) LED Undercabinet Light
  • HU30MSCTD48P (Plain White)
  • HU30MSCTD48MB (Matte Black)
• Universal Plug-in USB Charging Port
  • HU30MUNVUP (Plain White)
  • HU30MUNVUMB (Matte Black)
• Universal Plug-in PIR Motion Sensor
  • HU30MUNVMSP (Plain White)
  • HU30MUNVMSMB (Matte Black)

Note:  9 inch fixture will not have any module cover. 18 inch fixture will have one module cover & 24, 36, 48 inch will have 2 module covers.

PIR Motion sensor & USB modules are sold separately. For installation of PIR & USB please follow the respective instructions sheets.

For OPTIONAL ITEMS AND ACCESSORIES

(Purchase separately)

Splice box

• HU109P (white)
• HU109MB (black)

Daisy Chain Connector

• HU101P (white 3” length)
• HU101MB (black 3” length)
• HU102P (white 6” length)
• HU102MB (black 6” length)
• HU1010P (white 12” length)
• HU1010MB (black 12” length)
• HU1011P (white 18” length)
• HU1011MB (black 18” length)
• HU103P (white 24” length)
• HU103MB (black 24” length)
• HU104P (white 120” length)
• HU104MB (black 120” length)

Male-Male Connector

• HU107P (white, 1-1/2” Male-Male Connector)
• HU107MB (black, 1-1/2” Male-Male Connector)

Master Power Switch

• HU10MSP (white)
• HU10MSMB (black)

Power Cord (120V Only)

• HU115P (white 48” length)
• HU115MB (black 48” length)

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For indoor use only.
• This product is not intended to be repaired by service personnel, in case of failure or component defect (unit can be thrown away).
• This product must not be disposed of together with domestic waste. This product has to be disposed at an authorized place for recycling of electrical and electronic appliances.
• Warning: Read and follow these instructions.
• Risk of fire/electric shock. The fixture does not have any user serviceable parts.
• FIXTURE IS NOT WATERPROOF and is not intended for use in showers, saunas, or in potentially wet locations. ALWAYS keep this fixture away from sinks, tubs, showers, etc.

CAUTION

• This fixture IS ONLY FOR USE ON 120-277V AC circuits.
• A hard wired fixture should be installed by a qualified electrician with 120V AC supply only when powered by the HU115 cord.
• This fixture MUST ALWAYS BE USED in accordance with all electrical and safety codes and ordinances, including the most recent National Electric Code (NEC) and with the Occupational Safety and Health Administration (OSHA) Volume 1 on General Industry Standards and Interpretations.
• ALWAYS make certain that the power source conforms to the requirements on the fixture.
• This fixture is intended for use as general indoor lighting. DO NOT use in potentially dangerous locations, such as flammable or explosive atmospheres.

Note: Per local codes and regulations install on circuit with GFCI outlet or AFCI breaker and support all cords or interconnect cables with mounting clips (not provided) every one foot.

FCC STATEMENT

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authorization to operate this equipment.

SAVE THESE INSTRUCTIONS AND WARNINGS.

MOUNTING YOUR FIXTURE AND WIRING

MOUNTING YOUR FIXTURE

WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.

WARNING: Personal injury and damage to the fixture and/or mounting surface may result if the fixture is pulled from the surface. To reduce the likelihood of injury or damage, mount only on a surface that is structurally sound.

1. Remove fixture (A) from a carton. Locate the parts bag containing the (2) mounting screws (B) and set aside until ready to mount the fixture.
2. Hold the fixture up to the undercabinet surface where it will be mounted.Mark the position of the mounting holes with a pencil. Set the fixture aside.
   • Note:  The fixture should be mounted away from the backsplash towards the front side of the cabinet, with the lens pointing towards the backsplash. See Figure 1A and Figure 1B.
3. Drill a small pilot hole in the undercabinet surface at each pencil mark.
4. Place the fixture (A) flush against the under-cabinet surface, lining up the mounting holes in the fixture with the pre-drilled pilot holes.
5. Insert (2) mounting screws into the two mounting holes (Figure 1). Tighten both screws to secure the fixture.

WIRING

Note: If using a splice box, follow the instructions included with the splice box.

CAUTION

• Check electrical power wires for damage or scrapes.

Note: This unit will not operate properly unless connected to a “grounded” electrical circuit. Electrical shock, overheating, low or no light output, and shortened lamp life can result if not properly grounded.

OPTION 1:  PLUG IN CORD (120V ONLY)

1. Connect the power cord (sold separately) to the fixture.
2. Plug the power cord into an outlet. (120V only)

OPTION 2:  WIRING DIRECTLY TO FIXTURE

1. Remove the screws holding the fixture cover to the fixture base. Figure 2
2. Open the fixture cover to a 45degree angle and remove it by gently pulling it out of the fixture base. See Figure 3A.
3. Disconnect the CCT selection switch wire that connects with fixture cover. See Figure 3B.
4. Remove the screws holding the cable clamp cover to the cable clamp base. See Figure 4A and 4B
5. Remove the cable clamp base and cable clamp cover, from the fixture end(s) which will have the wired connection. See Figure 4C.
   • Note: If choosing installation Option 2B-Flexible Armored Cable, discard cable clamp bracket assembly as it is not needed.
   • Note: If using back conduit knockout, simply remove the conduit plug and discard. (Figure 4D)
6. Place a screwdriver on

OPTION 2A:  WIRING DIRECTLY TO FIXTURE -ELECTRICAL WIRE

1. Place the cable clamp base back into its original position shown in Figure 6A.
2. Fit electrical wire through the circular opening of the end cap (created in Option 2, Step 6) from outside the fixture. The electrical wire should also fit through the oval opening of the clamp base. See Figure 6B.
3. Fasten the clamp cover back on with the screws (same that was removed in Option 2, Step 4) to 5.5in-lb. See Figure 7.
4. Once the electrical wire has been secured to the cable clamp bracket wire in the following manner:
   • Using the push-in connectors prewired into the fixture, connect the bare copper wire of the electrical cable to an open position of the push-in connector which has a green (ground) wire already connected to it.
   • Connect the white (neutral) cable wire to an open position of the push-in connector which has a white (neutral) wire already connected to it.
   • Connect the black (hot) cable wire to an open position of the push-in connector which has a black (hot) wire already connected to it.
   • Tuck wires and push-in connectors back into the fixture wiring compartment.
   • Repeat previous steps of Figure 4A through 4B, if also using electrical cable to connect a separate fixture in series.
5. Position fixture cover at 45 degree from horizontal. Place fixture cover back into the fixture base. See Figure 10.
6. Reconnect the CCT selectable switch wire that disconnected in Option 2 Step 3.
7. Using the screws removed in Option 2 step 1, fasten the fixture cover to the fixture base with 2.6-3.5 lb.in torque. See figure 11.

OPTION 2B: WIRING DIRECTLY TO FIXTURE

Flexible Armored Cable (Installation is specific for use with 5/16” armored cable/flexible conduit)

1. Twist conduit connector onto the armored cable end, until a tight fit is reached. See Figure 8.
2. Fit armored cable with conduit connector going in first, through the knock-out hole from outside of the fixture. See Figure 9.
3. Once the electrical wire has been secured to the cable clamp bracket wire in the following manner:

• Using the push-in connectors prewired into the fixture, connect the bare copper wire of the electrical cable to an open position of the push-in connector which has a green (ground) wire already connected to it.
• Connect the white (neutral) cable wire to an open position of the push-in connector which has a white (neutral) wire already connected to it.
• Connect the black (hot) cable wire to an open position of the push-in connector which has a black (hot) wire already connected to it.
• Tuck wires and push-in connectors back into the fixture wiring compartment.
• Repeat previous steps of Figure 4A through 4B, if also using electrical cable to connect a separate fixture in series.

1. Position fixture cover at 45 degree from horizontal. Place fixture cover back into the fixture base. See Figure 10.
2. Reconnect the CCT selectable switch wire that disconnected in Option 2 Step 3.
3. Using the screws removed in Option 2 step 1, fasten the fixture cover to the fixture base 2.6-3.5 lb.in torque. See figure 11.

ADDITIONAL FIXTURE INSTALLATION

Additional fixtures may be wired in a series using the following options:

1. Daisy chain connector (HU101, HU102, HU103, HU104, HU1010, and HU1011).
2. Approved electrical wire, including armored metal cable

DIMMING

The Halo LED luminaire can be dimmed with phase-control dimmers (leading edge and trailing edge phase cut). Refer to product dimming information guide at www.cooperlighting.com; and consult the dimmer manufacturer for their latest dimmer listings, load ratings and product information.

Note

• fixtures with PIR sensor & USB module connected are non-dimmable.

OPTIONAL PIR SENSOR & USB PORT AVAILABILITY

In Rush Current Values| Fixture| Peak Current (120VAC)| Current Width (120VAC)| Peak Width (277VAC)| Current Width (277VAC)
---|---|---|---|---|---
9” Fixture| 0.76| 90| 1.52| 130
18” Fixture| 1.03| 81.2| 1.72| 76
24” Fixture| 1.55| 56| 2.23| 72
36” Fixture| 1.79| 63| 2.54| 46
48” Fixture| 1.93| 60| 2.7| 88
Maximum Wattage         A combination of any number of fixture lengths cannot exceed 440W
Connector Wire Gauge 14-18 AWG
Connector Wire Type      Solid, stranded

LIMITED WARRANTY

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

Cooper Lighting Solutions (“CLS”) warrants to customers that, for a period of five years from the date of purchase, Halo HU30 products will be free from defects in materials and workmanship. The obligation of CLS under this warranty is expressly limited to the provision of replacement products.

This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to CLS. This is required before warranty performance shall be rendered.  This warranty does not apply to CLS products that have been altered or repaired or that have been subjected to neglect, abuse, misuse  or accident (including shipping damages). This warranty does not apply to products not manufactured by CLS which have been  supplied, installed, and/or used in conjunction with CLS products. Damage to the product.

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. CLS warrants to customers that, for a period of five years from the date of purchase, Halo HU30 products will be free from defects in materials and workmanship. The obligation of CLS under this warranty is expressly limited to the provision of replacement products.

This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase is acceptable to CLS. This is required before warranty performance shall be rendered. This warranty does not apply to CLS products that have been altered or repaired or that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by CLS which have been supplied, installed, and/or used in conjunction with CLS products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY

IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS, THEREFORE, EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused. CLS is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.

Reproductions of this document without the prior written approval of CLS are strictly prohibited.

Contact

Cooper Lighting Solutions

• 1121 Highway 74 South Peachtree City, GA 30269
• P: 770-486-4800
• www.cooperlighting.com

© 2023 Cooper Lighting Solutions
All Rights Reserved.
Specifications and dimensions subject to change without notice.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>