HALO AL7550LPCGY LED Area Light Instruction Manual

: June 16, 2024
: HALO

Table of Contents

HALO AL7550LPCGY LED Area Light
Product Information
Product Usage Instructions
PACKAGING CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
MOUNTING AND WIRING YOUR FIXTURE
TROUBLESHOOTING
5-YEAR LIMITED WARRANTY
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

HALO AL7550LPCGY LED Area Light

HALO-AL7550LPCGY-LED-Area-Light-product-image

Product Information

Specifications :

Model: AL7550LPCGY (Gray), AL7550LPCBZ (Bronze)
Packaging Contents:
- A. Light fixture
- B. Access cover
- C. (3) Mounting screws
- D. Pole mounting clamp
- E. (3) Wire connectors
Light Sensor: Included
Conduit Connection: Yes
Weatherproof Rating: Suitable for wet locations
UL Listing: cULus Listed suitable for wet locations
Power Source: Requires connection to an outlet on a separate circuit

Product Usage Instructions

Mounting and Wiring Your Fixture:
NOTE: This fixture is intended to be conduit connected to a properly installed and properly grounded metal weatherproof junction box (not included). All conduit connectors, conduit, and junction boxes (sold separately) should be cULus Listed suitable for wet locations.

Turn off the power at the main fuse/breaker box.
Using the pattern on the box, mark and drill holes for mounting. Mount this fixture in an upright and level position.
Install the two bottom mounting screws (C) first, leaving enough room between the mounting screws and the mounting surface to accommodate mounting the fixture.
Screw the top mounting screw (C) into the predrilled hole and back the screw out. This will leave the hole threaded and make installation of the fixture easier.
Remove cover plate by loosening the two screws inside the cover plate. Do not remove the screw.
Remove access cover (B) from fixture (A). Install the first conduit connector and conduit (sold separately) into the access cover (B).
Feed supply wires into conduit. Attach ground wire that is attached to fixture housing (A) to the junction box earth ground wire.
Connect the black fixture wire to the black supply wire (hot) with UL-approved wire connector (E). Connect the white fixture wire to the white supply wire (neutral) with UL-approved wire connector (E).
Make sure no bare strands of wire extend from the wire nut or other approved wire connectors (E).
Attach access cover (B) to the light fixture (A) using the two access cover mounting screws provided (F).
Make sure all wiring is placed into the arm prior to tightening the access cover screws.
Place the fixture (A) on the two lower mounting screws (C) and install the upper mounting screw (C). Tighten all mounting screws to secure the fixture (A).
Reinstall the cover plate, making sure to tighten the two screws to secure the lens to the fixture (A).
Install photo control by inserting into socket and turning clockwise until prongs lock into place.

Frequently Asked Questions:

Q: What is included in the packaging?
A: The packaging includes a light fixture, access cover, (3) mounting screws, pole mounting clamp, light sensor, and (3) wire connectors.
Q: What is the weatherproof rating of this fixture?
A: This fixture is suitable for wet locations and has a cULus Listing for wet locations.
Q: How should I connect the fixture to the power source?
A: The fixture should be conduit connected to a properly installed and properly grounded metal weatherproof junction box. Make sure to follow the provided wiring instructions and consult a professional if needed.

Instruction Manual Questions?

PACKAGING CONTENTS

$HALO-AL7550LPCGY-LED-Area-Light-01 $2$$

ITEMS REQUIRED
(Purchase separately)

Phillips screwdriver
Adjustable wrench or ratchet wrench with 10mm socket
Drill with 3/16 in. drill bit
1/2 in. diameter conduit (if applicable, length depends on application)
1/2 in. watertight conduit connectors (if applicable)
Wire connectors

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

Heed all warnings, including below warnings AND those included on product.
Save these instructions and warnings.
For outdoor use only.
cULus LISTED for wet location use.

Warning

Read and follow these instructions.
Disconnect at fuse or circuit breaker before installing or servicing.
Edges may cut. Handle with care.

CAUTION

Connect fixture to a 120V-277V, 60 Hz power source. Any other connection voids the warranty.
Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
Upside down installation can result in overheating or accumulation of water in fixture. Install right side up.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authorization to operate this equipment.

SAVE THESE INSTRUCTIONS.

MOUNTING AND WIRING YOUR FIXTURE

NOTE: This fixture is intended to be conduit connected to a properly installed and properly grounded metal weatherproof junction box (not included). All conduit connectors, conduit, and junction boxes (sold separately) should be cULus Listed suitable for wet locations.

Turn off the power at the main fuse/breaker box.
Using the pattern on the box, mark and drill holes for mounting.
NOTE: Mount this fixture in an upright and level position.
Install the two bottom mounting screws (C) first, leaving enough room between the mounting screws and the mounting surface to accommodate mounting the fixture.
Screw the top mounting screw (C) into the predrilled hole and back the screw out. This will leave the hole threaded and make installation of the fixture easier.
Remove cover plate by loosening the two screws inside the cover plate. Do not remove the screw.
Remove access cover (B) from fixture (A). Install the first conduit connector and conduit (sold separately) into the access cover (B) (Fig. 1).
Feed supply wires into conduit. Attach ground wire that is attached to fixture housing (A) to the junction box earth ground wire.
Connect the black fixture wire to the black supply wire (hot) with UL-approved wire connector (E). Connect the white fixture wire to the white supply wire (neutral) with UL-approved wire connector (E). NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire extend from the wire nut or other approved wire connectors (E).
Attach access cover (B) to the light fixture (A) using the two access cover mounting screws provided (F) (Fig. 1).
NOTE: Make sure all wiring is placed into the arm prior to tightening the access cover screws.
Place the fixture (A) on the two lower mounting screws (C) and install the upper mounting screw (C). Tighten all mounting screws to secure the fixture (A).
Reinstall the cover plate, making sure to tighten the two screws to secure the lens to the fixture (A)
Install photo control by inserting into socket and turning clockwise until prongs lock into position. Photo control sensor window should aim North for best performance. To aim photo control, loosen the two screws on the socket cover and rotate socket until the arrow on the socket aligns with North. Tighten the socket screws to lock in place and install the photo control.
Connect second conduit and conduit connector at the junction box (Fig. 1).
NOTE: This fixture can be mounted on 1-5/8 in. diameter extension arms (sold separately). When installing fixture onto an extension arm, remove the access cover (B) and use the included pole mounting clamp (D) and access cover mounting screws (F).
14. Turn power back ON.

TROUBLESHOOTING

*Problem*	*Cause*	*Solution*
Light does not come on or light comes on for only a few seconds.	No
power to the fixture.

Check if circuit breaker tripped.
Confirm wall switch is ON.

Light sensor is not working properly.| Check if light is being reflected into the sensor, causing the fixture to turn off.
Wiring to the unit is loose.| TURN OFF POWER BEFORE CONTINUING.
Confirm wiring is properly secured.
Light does not shut off during daytime.| Light sensor is not receiving enough light to trigger switch.| Shine a flashlight into the light sensor for 2-3 minutes. The fixture should switch off after two minutes. This means the sensor is not receiving enough light; reposition or relocate the fixture.
Light cycles on and off.| Light sensor is sensing reflected light.| Cover light sensor with a piece of black electrical tape. The fixture should turn on after a slight delay. This means that extraneous or reflected light from the fixture is causing the sensor to turn the unit off. Install fixture where there is no reflective light.

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions (“CLS”) warrants to customers that, for a period of five years from the date of purchase, CLS products will be free from defects in materials and workmanship. The obligation of CLS under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to CLS.
This is required before warranty performance shall be rendered. This warranty does not apply to CLS products that have been altered or repaired that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by CLS which have been supplied, installed, and/or used in conjunction with CLS products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:

IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact CLS at 1-800-334-6871, press option 2 for Customer Service, or via e-mail [email protected] and include the following information:
- Name, address and telephone number
- Date and place of purchase
- Catalog and quantity purchase
- Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused. CLS is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim ﬁled with them.
Reproductions of this document without prior written approval of CLS are strictly prohibited.