LNC LFMZ773525549C Mouillure 5-Light 35.4-in L Matte Black and Polished Gold Instruction Manual

June 15, 2024
LNC

LNC LFMZ773525549C Mouillure 5-Light 35.4-in L Matte Black and Polished

Gold

Specifications:

  • Item Number: A05255
  • Voltage: 120V
  • Maximum Wattage: Type T, Max 60W per bulb

Product Usage Instructions

Safety Precautions:

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

Mounting Surface Preparation:

Before installation, make sure the mounting surface meets the following requirements:

  • Clean, dry, flat, and strong enough
  • 1/4 larger than the canopy on all sides
  • Any gaps between the mounting surface and canopy exceeding 3/16 should be corrected as required.

Weight Capacity Check:

Ensure that the ceiling or wall can stand the weight of the lampbefore installation.

Lamp Voltage and Bulb Replacement:

  • Make sure the voltage you are using is 120V.
  • The maximum wattage is Type T, Max 60W per bulb.
  • Keep the lamp away from acidic and alkaline substances to prevent damage to the lamp’s surface.
  • When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.

Electrical Wiring:

  1. Follow the provided charts to connect wires correctly:
    • Connect Black or Red Supply Wire to the OUTLET BOX GROUND or GREEN GROUND SCREW.
    • Connect White Supply Wire to the OUTLET BOX GROUND or FIXTURE GROUND.
    • Never connect other wires to ground wires.
  2. Make sure to use the appropriate wire connectors provided (A) to secure the connections.

Assembly and Installation:

  1. Carefully remove the fixture from the carton and ensure all parts and accessories are included.
  2. Screw tubes (I) to the nipple of body (J) and close quick links (G).
  3. Mounting Plate (C) should be installed with the side marked GND facing out.
  4. Follow the provided charts to connect wires correctly.
  5. Use the mounting screws (B) to secure the assembled screws on mounting plate (C).
  6. Double-check that everything is installed properly before turning on the light.

FAQ:

Q: What tools are required for assembly and installation?
A: The following tools are needed (NOT INCLUDED):

  • Ladder
  • Philips Head or Flat Blade Screwdriver
  • Electrical Tape
  • Pliers
  • Wire Cutter/Stripper

Q: How many parts and accessories are included?
A: The following parts and accessories are included:

  • (C) Mounting plate – Quantity: 1
  • (D) Green ground screw – Quantity: 1
  • (E) Canopy – Quantity: 1
  • (F) Loop – Quantity: 4
  • (G) Quick link – Quantity: 2
  • (H) Ball nut – Quantity: 2
  • (I) Tube
  • (J) Body – Quantity: 1

Q: How do I connect the ground wires?
A: Connect the ground wires according to the provided chart.

Q: What should I do if the mounting surface is not large enough?
A: Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.

Q: Can I use bulbs with wattage higher than 60W?
A: No, the maximum wattage per bulb is 60W.

Q: Can I connect other wires to ground wires?
A: No, never connect other wires to ground wires.

Q: Can I install the lamp without shutting off the electricity?
A: No, always shut off the electricity before starting any work.

Q: Can I use the lamp with voltages other than 120V?
A: No, the lamp is designed for use with 120V voltage only.

Q: Can I use the lamp in areas with acidic or alkaline substances?
A: No, keep the lamp away from acidic and alkaline substances to prevent damage to the lamp’s surface.

Item Number : A05255
WARNING (To reduce the risk of fire, electric shock, or personal injury):

INSTRUCTION

  1. We suggest installation by a licensed electrician.

  2. Please read the instruction carefully and save it as you may need it at a later time.

  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.» Go to the main fuse, or circuit breaker, box in your home.
    Place the main power switch in the “OFF” position.» Place the wall switch in the “OFF” position.

  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

  6. Make sure the voltage you are using is 120V. The maximum wattage is Type T, Max 60W per bulb.

  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

  • (C) Mounting plate(1)
  • (D) Green ground screw (1)
  • (E) Canopy (1)
  • (F) Loop (4)
  • (G) Quick link (2)
  • (H) Ball nut (2)
  • (I) Tube
  • (J) Body (1)

ACCESSORIES & QTY ENCLOSED:

  • (A) Wire connector (3)
  • (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Make pre-installation

  3. Step A1 » 1) Carefully pass the fixture wires through one side of tubes (I) and loops (F). 2) Screw tubes (I) to nipple of body (J).

  4. Step A2 » Open quick links (G). Attach quick links (G) to loops (F) on canopy (E) and on the top of tubes (I). Close quick links (G).

  5. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

  6. Go to the main fuse, or circuit breaker, box in your home.
    Place the main power switch in the “OFF” position.

  7. Place the wall switch in the “OFF” position.

  8. Make installation
    Step B1 » Unscrew ball nuts (H) from mounting plate (C).
    Step B2 » Attach mounting plate (C) to the outlet box with mounting screws (B).
    Note : the side of mounting plate (C) marked “GND” must face out.
    Step B3 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.
    Step B4 » Make wire connections
    Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES
    Connect ground wires according to the chart below
    Connect wires according to the chart below
    Twist wires together with plastic wire connectors until tightly joined.
    Wrap each connector with approved electrical tape and sure that no wire strands are exposed.
    Carefully tuck all wires into the outlet box
    Step B5 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening ball nuts (H) onto pre-assembled screws on mounting plate (C).

  9. NOTE: canopy (E) should be snug against the ceiling with ball nuts (H).
    If not, remove canopy (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):

  10. First, unscrew the pre-assembled hex nuts.

  11. Then, screw the pre-assembled mounting screws in or out of the mounting plate (C).

  12. When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step B5.
    Step B6 » Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

  13. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals